tams elektronik FCS-4 Manual de usuario
n
n
n
FCS-4 n
n
n
Einsatzfahrzeug-Modul
für Faller* Car-System n
n
Emergency vehicle module
compatible to the
Faller* Car-System nAnleitung
nManual
Module pour véhicule
d'intervention
du Faller* Car-System nMode d´emploi
nHandleiding
Module voor
hulpverleningsvoertuigen
voor het Faller* Car System n
n
Art.-Nr. 22-01-071-4 n
n
n
n
n
nDeutsch 3
nEnglish 19
nFrançais 33
nNederlands 48
n
n
n
n
n
n
n
n
© 07/2005 Tams Elektronik GmbH
Alle Rechte, insbesondere das Recht
der Vervielfältigung und Verbreitung
sowie der Übersetzung vorbehalten.
Vervielfältigungen und Reproduktionen
in jeglicher Form bedürfen der
schriftlichen Genehmigung durch die
Tams Elektronik GmbH.
Technische Änderungen vorbehalten.
© 07/2005 Tams Elektronik GmbH
All rights reserved. No part of this
publication may be reproduced or
transmitted in any form or by any
means, electronic or mechanical,
including photocopying, without prior
permission in writing from Tams
Elektronik GmbH.
Subject to technical modification.
© 07/2005 Tams Elektronik GmbH
Tout droits réservés, en particulier les
droits de reproduction et de diffusion
ainsi que le traduction. Toute
duplication ou reproduction sous
quelque forme que ce soit nécessite
l´accord écrit de la societé Tams
Elektronik GmbH.
Sous réserve de modifications
techniques.
© 07/2005 Tams Elektronik GmbH
Alle rechten voorbehouden. Niets uit
deze publicatie mag worden
vermenigvuldigd opgeslagen of
openbaar gemaakt, zonder
voorafgaande schriftelijke toestemming
van Tams Elektronik GmbH.
Technische wijzigingen voorbehouden.
n
FCS-4 English
Page 19
Table of contents
How to use this manual 19
Intended use 20
Safety instructions 20
EMC declaration 22
Summary of operation 22
Technical specifications / Circuit Diagram(Fig. 1) 24
Checking the package contents 24
Required tools and materials 25
Safe and correct soldering 25
Special features of the additional components 26
Mounting the FCS-4 27
FAQ 30
Manufacturer's note 31
Certification 31
Conditional warranty 31
Connections (Fig. 2) II
(Page II in the centre of this handbook is removeable.)
How to use this manual
If you have no specialist technical training, this manual gives step-by-
step instructions for safe and correct fitting of the module, and
operation. Before you start, we advise you to read the whole manual,
particularly the chapter on safety instructions and the FAQ chapter. You
will then know where to take care and how to prevent mistakes which
take a lot of effort to correct.
Keep this manual safely so that you can solve problems in the future. If
you pass the module on to another person, please pass on the manual
with it.
English FCS-4
Page 20
!
Intended use
Caution:
Integrated circuits are very sensitive to static electricity. Do not touch
components without first discharging yourself. Touching a radiator or
other grounded metal part will discharge you.
The module can be used according to the specifications of this manual
in a vehicle compatible to the Faller* Car-System. The stored software
is designed for controlling a emergency vehicle with siren.
The module is not suitable for children under the age of 14.
Reading, understanding and following the instructions in this manual
are mandatory for the user.
Any other use is inappropriate and invalidates any guarantees.
Safety instructions
Mechanical hazards
Cut wires can have sharp ends and can cause serious injuries. Watch
out for sharp edges when you pick up the PCB.
Visibly damaged parts can cause unpredictable danger. Do not use
damaged parts: recycle and replace them with new ones.
Electrical hazards
§Touching powered, live components,
§touching conducting components which are live due to malfunction,
§short circuits,
§connecting the circuit to another voltage than specified,
§impermissibly high humidity,
§condensation build up
can cause serious injury due to electrical shock. Take the following
precautions to prevent this danger:
§Never perform wiring on a powered module.
FCS-4 English
Page 21
§Mounting the module should only be done in closed, clean, dry
rooms. Beware of humidity.
§Only use low power for this module as described in this manual and
only use certified transformers.
§Connect soldering irons only in approved mains sockets installed by
an authorised electrician.
§Observe cable diameter requirements.
§After condensation build up, allow a minimum of 2 hours for
dispersion.
§Use only original spare parts if you have to repair the kit or the
ready-built module.
Fire risk
Touching flammable material with a hot soldering iron can cause fire,
which can result in injury or death through burns or suffocation.
Connect your soldering iron or soldering station only when actually
needed. Always keep the soldering iron away from inflammable
materials. Use a suitable soldering iron stand. Never leave a hot
soldering iron or station unattended.
Thermal danger
A hot soldering iron or liquid solder accidentally touching your skin can
cause skin burns. As a precaution:
§use a heat-resistant mat during soldering,
§always put the hot soldering iron in the soldering iron stand,
§point the soldering iron tip carefully when soldering, and
§remove liquid solder with a thick wet rag or wet sponge from the
soldering tip.
Dangerousenvironments
A working area that is too small or cramped is unsuitable and can cause
accidents, fires and injury. Prevent this by working in a clean, dry room
with enough freedom of movement.
English FCS-4
Page 22
Other dangers
Children can cause any of the accidents mentioned above because they
are inattentive and not responsible enough. Children under the age of
14 should not be allowed to work with this module.
Little children can swallow small components with sharp edges, with
fatal results! Do not allow components to reach small children.
In schools, training centres, clubs and workshops, assembly must be
supervised by qualified personnel.
In industrial institutions, health and safety regulations applying to
electronic work must be adhered to.
EMC declaration
This product is developed in accordance with the European standards
EN 55014 and EN 50082-1, tested corresponding to the EC - directive
89/336/EWG (EMVG of 09/11/1992, electromagnetic tolerance) and
meets legal requirements.
To guarantee the electromagnetic tolerance you must take the
following precautions:
§Make no changes to the original parts and accurately follow the
instructions, circuit diagram and connections diagrams included
with this manual.
§Use only original spare parts if you have to repair module.
Summary of operation
The module is particularly designed for the use in vehicles compatible
to the Faller* car system, that are run with two accumulator batteries. It
has six in- and outputs for the connection of LEDs, motor, reed contact
and a loudspeaker. Additional white LEDs for the front lighting can be
connected to the additional output. It is not necessary to use all
outputs. The in- and outputs are controlled from the software stored in
the IC. The software is designed for controlling an emergencyvehicle.
The voltage of 2,4 V that is provided by the vehicle accumulator batteries, is
doubled by the module. This enables white and blue LEDs to be connected,
FCS-4 English
Page 23
which normally need a voltage of more than 2,4 V. Red and yellow LEDs
may be connected directly via series resistors to the accumulator batteries,
provided they are not to be controlled by the software.
Front lighting
There can be connected up to two additional white LEDs for the front
lighting to the additional output. These LEDs are not controlled by the
software.
N.B. In contrast to the LEDs connected to the outputs controlled by the
software these should be connected via series resistors. Otherwise the
connected LEDs are damaged and the circuit may not work as intended.
Back lighting
It is possible to connect two red LEDs to one output of the module for
the back and stop lights. While breaking and some seconds after
stopping, the back lights are switched brighter, provided that the reed
contact existing in the vehicle is connected to the module.
Flashing lights
It is possible to connect two LEDs to one output of the module for the
flashing lights. These flash shortly two times each alternately and go off
again for a short time. The flashing lights are in operation as long as
the vehicle is supplied with voltage.
Siren
It is possible to connect a loudspeaker to one output of the module
which is switched on and off in short intervalls while the vehicle is in
motion. If the reed contact existing in the vehicle is connected to the
module the loudspeaker is switched off when the vehicle stops and
switched on while starting.
Driving of the motor
The reed contact that is in the vehicle can be connected to the module.
The module then influences the motor: After a stop it starts gently.
Additionally the back lights are switched brighter while the vehicle is
stopping and a few seconds after a halt and the siren is switched off.
English FCS-4
Page 24
Technical specifications
Supply voltage 2 to 3 Volt D.C.
Current consumption
(without connected loads) approx. 4 mA
Max. total current 80 mA
Max. current per output 20 mA
Protected to IP 00
Ambient temperature in use 0 - + 60 °C
Ambient temperature in storage -10 - + 80 °C
Comparative humidity allowed max. 85 %
Dimensions approx. 12 x 18 x 2,1 mm
Weight approx. 0,5 g
Fig. 1:
Cicuit Diagram
Checking the package contents
Check the contents of the package for completeness after unpacking:
§one module,
§additional components: one resistor 10 kΩ, one diode 1N4148, two
transistors BC 327, a loud speaker,
§one manual.
FCS-4 English
Page 25
!
Required tools and materials
Make sure you have the following tools and materials ready for use:
§an electronic soldering iron (max. 30 Watt) with a fine tip,
§a soldering iron stand,
§a tip-cleaning sponge and a heat-resistant mat,
§a small side cutter and wire stripper,
§a pair of tweezers,
§tin solder (0,5 mm. diameter),
§enamelled copper wire or thin connecting wire,
§LEDs for the lights,
§if necessary: series resistors for the front lights.
Safe and correct soldering
Caution:
Incorrect soldering can cause dangers through fires and heat. Avoid
these dangers by reading and following the directions given in the
chapter Safety instructions. If you have had training in soldering you
can skip this chapter.
§Use a small soldering iron with max. 30 Watt. Keep the soldering tip
clean so the heat of the soldering iron is applied to the solder point
effectively.
§Only use electronic tin solder with flux.
§When soldering electronic circuits never use soldering-water or
soldering grease. They contain acids that can corrode components
and copper tracks.
§Solder quickly: holding the iron on the joints longer than necessary
can destroy components and can damage copper tracks or
soldering eyes.
§Apply the soldering tip to the soldering spot in such a way that the wire
and the soldering eye are heated at the same time. Simultaneously add
solder (not too much). As soon as the solder becomes liquid take it
English FCS-4
Page 26
away. Hold the soldering tip at the spot for a few seconds so that the
solder flows into the joint, then remove the soldering iron.
§The joint should be held still for about 5 seconds after soldering.
§To make a good soldering joint you should use a clean and
unoxidised soldering tip. Clean the soldering tip with a damp piece
of cloth, a damp sponge or a piece of silicon cloth.
§After soldering check (preferably with a magnifying glass) tracks for
accidental solder bridges and short circuits. This would cause faulty
operation or, in the worst case, permanent damage. You can
remove excess solder by putting a clean soldering tip on the spot.
The solder will become liquid again and flow from the soldering
spot to the soldering tip.
Special features of the additional components
Resistors
Resistors reduce current. Their mounting orientation is of no
importance. The value of resistors for smaller power ratings
(under 5 W) is indicated through colour rings. Every colour
stands for another figure. The added resistor has a value of
10 kΩ (colour rings brown - black – orange – gold).
Diodes
Diodes allow the current to pass through in one direction only
(forward direction). The diode type is printed on the body.
Diodes must be mounted in a given direction. The negative
end is marked with a ring.
Transistors
Transistors are current amplifiers which convert low signals
into stronger ones. They have three contacts. As they are
polarized, they have to be mounted in a certain direction. Die
BC-Types have a housing in form of a half cylinder (SOT-
housing). The three connecting points are called basis (B),
collector (C) and emitter (E).
Tabla de contenidos
Otros manuales de Accesorios para automóviles de tams elektronik
