Tally Dascom 7206 Series Manual de usuario
– 1 –
Installation and 7106 7206
User Guide Auto Cutter
– 2 –
©
August 2010 DASCOM Europe GmbH
– 3 –
Installation Guide
Installing the cutter stand unit
(1) Check to make sure that the printer’s power switch is turned off, then
disconnect the power cord.
(2) Open the top cover.
(3) Lift and remove the front cover from the printer. (Keep the removed
cover in a safe place, because it is used when the auto cutter has been
removed.)
– 4 –
(7) Feed the cable, in 6, so that it lies along the printer’s case. When
replacing the connector cover and the motor cover, take care that the
covers do not pinch the cable.
(8) Set the cutter-stand-unit to the front of the printer with the screw (2)
provided.
Cable
– 5 –
(4) Remove the screw (1) fastening the motor cover, and then lift and
remove the motor cover. Take care that the screw does not fall inside
the printer chassis.
(5) Remove the screw (1) fastening the optional unit connector cover, and
then remove the optional unit connector cover.
(6) Plug the connector of the cutter-stand-unit cable into the optional
connector on the printer.
– 6 –
Installing the cutter unit
(9) Plug the connector of the cutter-unit cable into the connector on the
cutter stand unit.
(10) Align the indentations (2) at the bottom of the cutter unit with the
protrusions (2) on the
cutter stand unit, and
then fasten the slotted
head screw on the
cutter unit with a
flat-blade screwdriver.
Take care that the
cutter unit does not
pinch the cable.
(11) After the cutter unit is
installed, reinstall the
motor cover and the
optional unit
connector cover on
the printer.
Note Be very careful as
the motor may be
hot.
(12) Close the top cover.
(13) Connect the power cord and turn on the
power switch of the printer.
Note Removing the cutter unit
To remove the cutter unit from the printer,
follow the installation steps in reverse order.
Hold the end of the cutter unit by your
hand in order that the cutter unit does not
fall from the printer when removing the
fastening screw.
– 7 –
User Guide
Contents
Notice
···················································
8
SAFETY SIGNS that must be strictly observed!
·········
10
1.
Function
·········································
11
2.
Main specifications of auto-cutter
················
11
3.
Checking items inside the accessory box
··········
·
·
·
·
12
4.
Auto-cutter settings
·······························
13
5.
Cut position
·······································
14
6.
Cut settings
·······································
15
7.
Auto cut-length detection
··························
16
8.
User maintenance
·································
17
9.
Troubleshooting
···································
18
·
·
·
·
– 8 –
Notice
1. Before use, be sure to read this manual and understand. And
keep it handy for reference when needed.
2. Do not handle, disassemble or repair any parts other than those
specified in this manual.
3. The contents of this manual may be changed without prior
notice.
4. Reproduction, transfer or transmission of the contents of this
manual without prior consent is strictly prohibited.
5. We are not liable for any damage resulting from the use of this
manual, regardless of omissions, errors or misprints.
6. We are not liable for any problems resulting from the use of
optional products or consumable supplies other than those
specified in this manual.
7. Please contact us if there are any mistakes or ambiguities within
this manual.
8. If there are missing or incorrectly collated pages in this manual,
contact us to obtain a new manual.
– 9 –
SAFETY SIGNS
that must be strictly observed!
To prevent personal injury or property damage, the following must be
strictly observed.
The degree of possible injury and damage due to incorrect use or
improperly following instructions specified is described below.
WARNING
CAUTION
This is a mark to call attention to the reader.
WARNING
Do not perform the following. If ignored, these may cause
damage to the auto-cutter, breakdown, overheating, smoke, fire
or electric shock. If the auto-cutter is damaged or breaks down,
turn off the power to the printer and remove the power cord from
the outlet and then consult your supplier.
Do not open the auto-cutter during operation.
The cutting blade can be very dangerous. Also, this can cause
damage.
Prevent foreign matter from entering small openings
of the auto-cutter
Inserting your finger or other foreign matter in the small
openings of the auto-cutter can be extremely dangerous and
can damage the cutter.
The user should never install or remove the auto
cutter.
Indicates a situation which, if not
observed and handled properly,
could result in death or serious
injury.
Indicates a situation which, if not
observed and handled properly,
could result in personal injury or
property damage.
– 10 –
CAUTION
Avoid the following conditions to ensure proper
operation of the auto-cutter.
The cutting blade can be very dangerous. Also, this can
cause damage.
Room temperature is less than 5°C or more than 40°C.
Humidity is less than 30% or more than 80%.
Dusty
Direct sunlight
Chemicals
Vibrations or impacts
When cutting media (paper)
Do not operate auto-cutter without loading paper. This can
cause damage to the cutter.
Use the standard media (paper). Otherwise, problems such
as paper jams may occur.
Remove any dust or particles from the paper guide and path
periodically.
When auto-cutter is cleaned, turn off the power to the
printer and remove the power cord from the outlet
beforehand.
Clean the main body of the auto-cutter with a soft cloth
that is soaked in a thinned neutral detergent. Do not use
volatile solvent such as benzene and thinner, which can
cause discoloration.
When the cutter blade becomes dirty, contact your
supplier or a service representative.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Cortador de otras marcas
Milwaukee
Milwaukee HEAVY DUTY M12 FCOT Manual de usuario
Makita
Makita DCS552 Manual de usuario
SignWarehouse.com
SignWarehouse.com Bobcat BA-60 Manual de usuario
Makita
Makita 4112HS Manual de usuario
GEISMAR STUMEC
GEISMAR STUMEC MTZ 350S Manual de usuario
Hitachi
Hitachi CM 4SB2 Guía de solución de problemas
