TagMaster S1566 Manual de usuario

TagMaster AB
TagMaster AB
TagMaster S1566 Heavy Duty
HW Installation Guide
Manual issue 01

TagMaster AB
HW Installation Guide TABLE OF CONTENTS Manual issue 01
2
Disclaimer
The information in this document is subject to change without notice. While the information
contained herein is assumed to be accurate, TagMaster AB assumes no responsibility for any
errors or omissions.
Copyright
The copyright of this document is and will remain ours. No part of this document may be
reproduced or transmitted in any form or by means, electronic or mechanical, for any purpose,
without the express written permission of TagMaster AB.
FCC ID: M39S15XX
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
Caution
Information to user.
Changes or modifications not expressly
approved by the party responsible
for compliance could void the
user’s authority to operate the equipment.
Reg. No. 03-074
TagMaster AB
Electrum 410
S-164 40 KISTA
Sweden
Tel: +46-8-632 19 50, Fax: +46-8-750 53 62

TagMaster AB
HW Installation Guide TABLE OF CONTENTS Manual issue 01
3
1 TABLE OF CONTENTS
1TABLE OF CONTENTS...................................................................................................... 3
2REVISIONS........................................................................................................................... 5
3ASSOCIATED DOCUMENTATION ................................................................................. 5
4INTRODUCTION................................................................................................................. 6
4.1 Audience.......................................................................................................................... 6
4.2 System Block Diagram.................................................................................................... 7
4.3 Definitions....................................................................................................................... 8
4.4 References ....................................................................................................................... 8
5SAFETY NOTICE ................................................................................................................ 9
5.1 General ............................................................................................................................ 9
5.2 Specific warning and caution statements are used throughout this manual.................. 10
5.3 Installation..................................................................................................................... 10
6SYSTEM COMPONENTS................................................................................................. 11
6.1 Communicators ............................................................................................................. 11
6.2 ID Tags.......................................................................................................................... 11
7ENVIRONMENTAL CONSIDERATIONS ..................................................................... 12
7.1 General .......................................................................................................................... 12
7.2 Electromagnetic immunity ............................................................................................ 12
8ELECTRICAL REQUIREMENTS................................................................................... 13
8.1 Temperature .................................................................................................................. 13
8.1.1 Communicators ..................................................................................................... 13
8.1.2 Tags ....................................................................................................................... 13
8.2 Supply Voltage.............................................................................................................. 13
8.3 Radio Interface .............................................................................................................. 13
9MECHANICAL INSTALLATION ................................................................................... 15
9.1 General .......................................................................................................................... 15
9.2 Readers .......................................................................................................................... 15
9.2.1 Mounting ............................................................................................................... 15
9.2.2 Connecting Cable recommendation ...................................................................... 16
9.3 ID-Tags.......................................................................................................................... 17
10 ELECTRICAL CONNECTIONS.................................................................................. 18
11 EARTHING REQUIREMENTS ................................................................................... 19
12 START-UP....................................................................................................................... 20
12.1 General .......................................................................................................................... 20
12.2 Inspection ...................................................................................................................... 20
12.3 Verifying communication ............................................................................................. 20
12.3.1 Serial host communication.................................................................................... 20
12.3.2 Reader - Tag communication ................................................................................ 20
13 TROUBLE SHOOTING................................................................................................. 22
13.1 An S1566 Reader malfunction ...................................................................................... 22
13.2 Unsuitable interface converters..................................................................................... 22

TagMaster AB
HW Installation Guide TABLE OF CONTENTS Manual issue 01
4
13.3 Interference.................................................................................................................... 22
13.4 Using wrong address ..................................................................................................... 22
13.5 Forgetting the free-wheel diode across inductive loads ................................................ 22
13.6 Using different data speed in the Tag(s) and in the Reader(s). ..................................... 22
13.7 Using an unsuitable power supply ................................................................................ 23

TagMaster AB
HW Installation Guide REVISIONS Manual issue 01
5
2 REVISIONS
Document revision history.
Revision Date Issued by Comment
01 2003-04-30 Dev. Dept. First issue
This document follows the TagMaster documentation version numbering standard to
identify the document version. This standard uses the form P01A, P01B to P01n for
draft versions (not for customer issue) then 01 for a released version (reviewed; can be
given to the customer). Subsequent issues use 02, 03, 04 etc and are changed via the
formal change control process.
3 ASSOCIATED DOCUMENTATION
51027803 TagMaster AB TagMaster HW Installation Guide
51021106 TagMaster AB Confident Programmer's Guide

TagMaster AB
HW Installation Guide INTRODUCTION Manual issue 01
6
4 INTRODUCTION
This manual describes the installation requirements and user information for the TagMaster
S1566 Heavy Duty Reader (HD-Reader).
4.1 Audience
The intended audience for this document is system integrators, installation engineers, contractors
or the like who have the task to install and commission the TagMaster systems. The audience is
expected to have adequate experience and education in the field of installation and
commissioning of control and identification systems and to be qualified for electrical
installations.

TagMaster AB
HW Installation Guide INTRODUCTION Manual issue 01
7
4.2 System Block Diagram
Microwaves
S1566 HD Reader
Interface cable
ID-Tag
Host
Diagram to show system and interconnections with a host and relation with tag.

TagMaster AB
HW Installation Guide INTRODUCTION Manual issue 01
8
4.3 Definitions
Reader Device (e.g. S1566) used to read and write Tags in the TagMaster system.
ConfiLib The CONFIDENT Library Software (ConfiLib) is the uniting name of the
device drivers that are included in all S1500/S1501/S1566 host C-language
software modules.
ConfiTalk Standard communication protocol. Used by Pyramid and Solid. Included
in ConfiLib.
Host IBM PC or compatible used as master computer in a TagMaster system.
Pyramid Pyramid is the S1500 standard software delivered from factory. S1500
with Pyramid is capable of taking decisions on its own when a Tag has
been read or when a movement has been detected. Refer to the S1500
datasheet for further details.
Solid Solid is the S1501 and S1566 standard software delivered from factory.
This software receives ConfiTalk commands on the serial port and
executes them. This is the same as the ConfiTalk only mode of the S1500.
Tag ID-carrier (e.g. ScriptTag S1251) in the CONFIDENT system which is
read/writable via microwaves, using a Communicator.
4.4 References
Communicator S1500&S1501 data sheet DS1500
Communicator S1503 data sheet DS1503
Communicator S1566 data sheet DS1566
ScriptTag S1251 data sheet DS1251
ScriptTag HD S1450 data sheet DS1450
ScriptTag HT S1350 data sheet DS1350
MarkTag S1255 data sheet DS1255
MarkTag HD S1455 data sheet DS1455
Card holder WinFix S1951 data sheet DS1951
Card holder Cardkeep S1953 data sheet DS1953
Mounting bracket S1952 data sheet DS1952
RS232/RS485 converter S1942 DS1942
Confident Programmer’s Guide 510211
Confident HW Installation Guide 51027802

TagMaster AB
HW Installation Guide SAFETY NOTICE Manual issue 01
9
5 SAFETY NOTICE
5.1 General
This Installation Manual shall be carefully read before any installation works is performed.
Special attention shall be paid to this page and the statements in boxes throughout the manual.
The contents of this document are not binding. If any significant difference is found between the
product and this document, please contact TagMaster AB for further information
We reserve the right to modify products without amending this document or advising the user.
We recommend using personnel authorised by TagMaster for all installation, service and repair
and the use of TagMaster genuine spare parts. TagMaster AB will not otherwise assume
responsibility for the materials used, the work performed or any consequences of the same.
Check the contents of the shipment for completeness and possible damage. If the contents are
incomplete or damaged, a claim should be filed with the carrier immediately and the TagMaster
Sales or Service organisation or the TagMaster representative should be notified in order to
facilitate repair or replacement of the equipment.
The equipment described in this manual is designed to be used by properly trained personnel
only. Installation, adjustments and maintenance of the exposed equipment shall be carried out by
qualified personnel who are aware of the hazards involved and who are qualified for electrical
installations.
For correct and safe use of this equipment, it is essential that both operating and service
personnel follow generally accepted safety procedures in addition to the safety precautions
specified in this manual.
The emitted power level from a TagMaster communicator is less than 10mW EIRP. This power
level is defined as very low and is far below the European levels that would require any form of
analysis when considering health risks. For comparison purposes, the emitted power level from a
TagMaster communicator is significantly less than that emitted by a typical mobile telephone.
TagMaster uses a radio frequency technology, which has been tested and conforms to the
requirements of the European CE mark approval for Short Range Devices.
To conclude, there is no risk to personal safety when working with or in close proximity to the
TagMaster communicator.

TagMaster AB
HW Installation Guide SAFETY NOTICE Manual issue 01
10
5.2 Specific warning and caution statements are used
throughout this manual.
CAUTION is used to indicate correct operation or maintenance procedures in order
to prevent damage to, or destruction of the equipment or other property.
WARNING indicates a potential danger that requires correct procedures or
practices in order to prevent injury to personnel.
Whenever it is likely that safe operation is impaired, the equipment must be made inoperative
and secure against unintended operation. The appropriate servicing authority must then be
informed.
5.3 Installation
Before any other connection is made, the equipment shall be mounted so that the metallic chassis
is connected to protective ground.
WARNING Interruption of the chassis connection with protective ground can
make the equipment dangerous if it is connected to a defective power supply.
The power supply used to provide the equipment with 24 or 12 VDC must comply with all
relevant safety regulations. It must also be made for connection to the local mains voltage
and be able to provide the necessary power without producing excessive heat.
•Fuses shall only be renewed by a qualified person who is aware of the risks involved.
The use of repaired fuses is prohibited.
•Capacitors inside the equipment can hold their charge even if the equipment has been
disconnected from all voltage sources.
•All PCB’s removed from the equipment must be adequately protected against damage and all
normal precautions regarding the use of tools must be observed.
•The equipment must be disconnected from all voltage sources before any installation or
service work is made.
CAUTION Damage may be the result if;
- The equipment is switched on when parts are removed from the PC board.
- A PCB is removed within one minute after switching off the equipment.
Tabla de contenidos
Otros manuales de Lector de tarjetas de TagMaster




















