SystemBase uLory Manual de usuario
uLory
User Guide
Version: 1.0
April 8th, 2019
uLory User Guide
2
Revision History
Date of Revision
Document
Version
Pages
Revised
Details of Revision
April 8th, 2019 1.0 All New
Copyright 2018 SystemBase Co., Ltd. All rights reserved.
Website http://www.sysbas.com/
Tel +82-2-855-0501
Fax +82-2-855-0580
16F (1601) Daerung Post Tower-1, 288, Digital-ro, Guro-gu, Seoul,
Republic of Korea
For inquiries, please contact us at [email protected]
uLory User Guide
3
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Caution
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
IMPORTANT NOTE : FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
uLory User Guide
4
Table of Contents
1. OVERVIEW ..................................................................................................................................... 5
2. FEATURE ......................................................................................................................................... 5
3. COMPONENTS .............................................................................................................................. 6
4. HARDWARE ................................................................................................................................... 7
4.1 Specification ...................................................................................................................................................... 7
4.2 LED ........................................................................................................................................................................ 8
4.3 Drawing of Device ........................................................................................................................................... 9
5. HOW TO CONNECT ..................................................................................................................... 9
5.1 Install USB Driver ........................................................................................................................................... 9
5.2 Check USB Serial Port .............................................................................................................................. 10
6. HOW TO USE ............................................................................................................................. 10
6.1 Switch Setting Table .................................................................................................................................... 11
6.2 Operation Mode Setting ........................................................................................................................... 11
7. UTILIZATION ............................................................................................................................... 18
uLory User Guide
5
1. OVERVIEW
ULory is a device that converts signals of RS232 Serial to LoRa to connect with Serial devices
that are several kilometers away.
LoRa (wireless communication technology for sensor networks), the next-generation
communication of technology of Low Power Wide Area (LPWA) capable of transmitting small
amounts of data over long ranges, enables communications up to 20 km in open terrain.
2. FEATURE
- Support low power and mid and long-range wireless communication of LoRa (Maximum of
20km in open terrain)
- Support industrial operating temperature range from -40 to 85℃
- Provide communication specification of USB 2.0
- Device setup with utilities such as Dip switch, AT Command and LoryView
uLory User Guide
6
3. COMPONENTS
COMPONENTS ORDER NUMBER
uLory-1010UIL, 2.625dBi Antenna, Quick
Manuals, SystemBase Covenant
uLory-1010UIL
Package
2.625dBi Antenna Product Brochure SystemBase Covenant
uLory User Guide
7
4. HARDWARE
4.1 Specification
CATEGORY SUBCATEGORY SPECIFICATION
Wireless
Interface
Frequency Band 917 ~ 923MHz
Modulation LoRa
Antenna +2.625 dBi Gain Load Antenna
Wired
Interface
Standard USB 2.0 A Type
Signal USB DP, DM
Display LED TXD, RXD, RDY
Operating
Environment
Temperature -40℃ ~ +85℃
Humidity 5~95%, non-condensable
Power DC 5V (USB VBUS)
uLory User Guide
8
4.2 LED
LED STATUS OPERATION
RDY
(YELLOW)
Blink (Interval of 0.5 sec.) Operation Mode (Default)
Blink (Interval of 0.1 sec.) Setup Mode
RXD
(RED)
On Reception of Data from LoRa to USB Port
Off -
TXD
(GREEN)
On Transmission of Data from USB Port to LoRa
Off -
* If the input voltage level is lower than the rated voltage, an operation error occurs and the
RDY LED will light up at the same time.
uLory User Guide
9
4.3 Drawing of Device
5. How to Connect
After the connection to the USB port of PC, uLory will be booted and RDY LED of the device
will “blink” in the 0.1-second interval under the Setup Mode and in the 0.5-second interval
under the Operation Mode.
* See 4.2 in the Manuals for details of LED operation.
5.1 Install USB Driver Installation
- A driver, USB 2.0 A Type, needed for uLory
- Download a driver from the library at http://www.sysbas.com
uLory User Guide
10
- Install the downloaded driver (USB One Click Driver) after connecting uLory to USB Port of
PC
5.2 Check USB Serial Port
- Check if USB Serial Port is created as below after installing a driver
6. How to Use
Users should adjust setting of Serial (interface, communication speed, parity bits and flow
control) and LoRa (channel, Spreading Factor) for the communication between uLorys or
with other devices in LoryNet via AT command or LoryView. The default Serial setting is as
follows: Baud rate of 9600, Data Bit of 8 and Stop Bit of 1. Here, Data Bit and Stop Bit are
not subject to change.
Tabla de contenidos
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario