Synectic Electronics SY028 Manual de usuario
SY028 Loadcell Amplifier with
High Level Relay
User Man al
Introd ction
The SY028 TA is a unipolar output load cell amplifier combined with a high
level relay trip. It can be specified with a 0 5V or 0 10V output. An LED
indicates the operation of the trip relay.
Loadcell amplifier as shipped
Dimensions
72.5mm x 18mm x 62mm
Special and Uniq e feat res
Unit mounts on a standard DIN rail
Separate high and low set points on unit
connects directly to a load cell or pressure sensor
Unit has got very high input impedance (2Gohms)
The unit has a unipolar Voltage out together with a high level trip relay
Multi turn trimmers set the output voltage span and the trip level. A known
weight can be used to set the trip point by connecting the unit and turning
the respective trimmer until the LED lights.
Installation
Before installation check that the unit is secure, not damaged and that the
environment specifications for the product are as indicated in the manual.
For the installation take into consideration the following:
I. Ensure easy access to the component
II. Ensure the component is stable upon installation
III. No contact with water or other electromagnetic components to minimise
interference
Connections
A: Ex (DC supply )
B: IN+
C: IN
D: EX+
E: DC Supply +
F: RLY1 (High)
G: Relay Common
H: Voltage out
Specifications
Parameter Min Typ Max
Supply voltage VDC (0-5V out)
(0-10V out)
7
12
24
24
30
30
Input options bri ge (loa cell, pressure sensor)
Excitation (V) 4.9 5 5.1
Input Sensitivity (mV/V) 0.25 10
Ban wi th (-3 B) 400Hz
Output step response 2msec
Output low voltage 0.04V 0.15V
Relay switching limits - 0.5A 200V peak
Relay trip response time 0.5msec (turn on) 1.2msec (turn
off)
Operating current 25mA (no cells) 85mA (4 x 350R
cells)
EMC Teste to BS EN 61000-4-21:2011
Operating temp.(C -40 85
Storage temperature (C) -55 125
Case H (on rail) = 72.5mm, W = 18mm, D = 62mm.
Moul e in grey flame resistant polyami e.
For use with rails to EN50035 (DIN46277-1)
asymmetric or
EN50022 (DIN46277-3) symmetric.
Connections Rising Clamp terminals with 3.5 x 2.5mm apertures
Inquiries and trouble shooting
For any inquiries or problems with the SY028Trip amp or other available
pro ucts checkout our website or sen email using the appropriate link below.
Website: www.synectic.co.uk
Email: [email protected]
DECLARATION OF CONFORMITY FOR
LOAD CELL AMPLIFIERS
Name of manufacturer or supplier: Synectic Design Lt
Registere office: 48 Brin ley Close
(inclu ing country of origin) Farnworth
Bolton
Lancashire
Englan
Postco e: BL4 0AG
Description of pro uct: SY028TA trip loa cell amplifier inclu ing all
variants
Stan ar s un er which conformity is eclare :
BS EN 61326-1: 2006 Electrical equipment for measurement,
control an laboratory use-EMC requirements.
Part1-2-3
BS EN 61000-4-2:1995, Immunity to electrostatic ischarge
1ec 61000-4-2:1995 Teste up an inclu ing level 8KV Air ischarge
BS EN 61000-4-3:2006 +A1:2008 Immunity to ra iate frequency electromagnetic
fiel s at 10V/M
BS EN 61000-4-4:2004 Immunity to electrical fast transient/burst. Test
levels
Up to an inclu ing +/-4KV on supply ports an
+/-2KV on input/output signal an ata ports.
(test Level 4)
Directive 2011/65/EU In relation to restriction of use of certain
hazar ous
(RoHS2) substances in electrical an electronic
equipment.
REACH (article 3) Synectic Electronics Lt are manufacturers of
electronic har ware. We are seen as a ‘ own stream user’ accor ing to REACH
regulations. We are therefore are not require to register with the European Agency
for chemicals ‘ECHA’.
Name of authorise representative: Brian Peter Tonge
Position of authorise representative: Technical Director
Declaration
I eclare that, as the authorise representative, the above information in relation to
the supply/manufacture of these pro ucts, when use as recommen e , are in
conformity with the state stan ar s an other relate ocuments following the
provision of EEC Directives.
Signature of authorise representative:
Date: 15/09/2015
Otros manuales de Amplificador de Synectic Electronics
