Swisher Predator WB924 Manual de usuario

THE PREDATOR

THE PREDATORTHE PREDATOR

THE PREDATOR

2424

24”

””

” ROUGH CUT

ROUGH CUT ROUGH CUT

ROUGH CUT

WALK BEHIND CUTTER

WALK BEHIND CUTTERWALK BEHIND CUTTER

WALK BEHIND CUTTER

OWNER’S

MANUAL

1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093

PHONE (660) 747-8183 FAX (660) 747-8650

MODEL NO.

Manufacturing quality lawn care equipment since 1945

Operation

Service and Adjustment

Repair Parts

Made In The

USA

Rev. 04-154

Read and follow all Safety

Rules and Instructions

before operating this

equipment.

WB924

swisherinc.com

ONWB924

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you

have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The

model number, serial number, date of purchase, and the name of the authorized Swisher dealer from

whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty may

last, so the above limitations or exclusions may not apply to you. This warranty gives you specific

legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty

as defined by the Magnuson-Moss Act of 1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects

in materials and workmanship for a period of two (1) year from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY..……………………….3-4

PRE-OPERATING..….……..……4

OPERATION.……………………….5-7

DECALS…..………….……………….8

PARTS BREAKDOWN…………….9-13

SAFE SLOPE GUIDE..………………15

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no

way is Swisher Mower Co., Inc. or its agents responsible for the engine

warranty. The Briggs & Stratton Engine Service Hot-Line is 1-800-

233-3723. The Tecumseh Engine Service Hot-Line is 1-800-558-5402.

2) Commercial Use This product is not intended for commercial use and carries no

commercial warranty.

3) Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher Mower Co., Inc., that has been subject to alteration,

misuse, abuse, improper assembly or installation, shipping damage, or

to normal wear of product.

4) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance.

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you for choosing Swisher’s 24” Rough Cut Walk Behind Cutter.

Before operating your cutter, please read, understand and follow all of the safety

precautions and other instructions explained in this manual. As with all power

equipment, lawnmowers can be potentially dangerous if not properly used.

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting,

adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in

a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate this

machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the mower

discharge direction and do not point at anyone. Stop the machine if anyone enters the

mowing area. Children are often attracted to the machine and the mowing activity.

Never assume that children will remain where you last saw them. Keep children

under the watchful care of another responsible adult.

•No riders!

• Do not put hands or feet near or under rotating parts.

• Do not mow in reverse. Always look down and behind before and during backing.

• Turn off the blade when not mowing. Before leaving the machine, turn off the blade

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower

as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear

only solid shoes with good traction when mowing.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running.

• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra

caution when servicing them. Do not operate at too fast a rate.

• Disengage spark plug wire and place where it cannot make a connection.

• Check engine oil. All engines are filled with oil at the factory. Verify oil level and

add if necessary before starting engine. (See Engine Owner’s Manual)

• Verify fuel level and add if necessary before starting engine.

• Reconnect spark plug wire.

• (Refer to Owner’s Manual pp. 5-7) For proper operating procedures.

PRE-OPERATING INSTRUCTIONS

The operation of any mower can produce foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles before staring any cutting machine and

while operating such a machine.

The operation of any cutter produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW CUTTER

INTENDED USE

This is not a lawn mower. The Predator is designed for cutting overgrown brush, weeds,

and other types of organic growth. This unit is capable of clearing small saplings of 1-

1/2” in diameter or less.

PROPULSION

The Predator is self-propelled, and is controlled by a “GROUND CONTROL” bail. To

engage the drive, put the transaxle in a gear and activate the lower bail. Releasing the bail

will disengage the self-propel.

Under most conditions cutting should be done in a low gear (1st or 2nd). Upper gears

should be used for conditions where weeds and brush are thinned out or not as tall. In

confined areas the machine can be pushed forwards or backwards by releasing the

“GROUND CONTROL” bail, placing the transaxle in neutral, and pushing the machine.

TRAVEL SPEED

Can be varied by choosing a higher or lower gear using the gearshift lever at the rear of

the machine or by changing the engine speed with the engine throttle. Do not adjust speed

with the blade engaged. To shift the cutter into reverse, release “GROUND CONTROL”

bail, disengage blade, and rotate the shift lever to the left. When the lever stops lift up the

reverse lockout latch and continue to move the shift lever to the left until it stops again.

Blade will not engage while cutter is in the “reverse” gear.

ENGAGING BLADE

An “OPERATOR PRESENCE” bail and a “BLADE ENGAGE” lever control work

together to engage the Predator’s blade. Both devices must be activated before the blade

will work. Releasing the “OPERATOR PRESENCE” bail will disengage both the blade

and the “BLADE ENGAGE” lever.

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel used.

Engine must be level to accurately check and fill oil. Do not overfill.

• Make sure unit is level, blade is disengaged, and transaxle in “NEUTRAL”

• Check spark plug wire, oil level, and fuel level.

• Check all electrical connections for build-up of debris.

• Set engine throttle to “CHOKE” position.

• Turn key to the “ON” position.

• Pull rope with a single fluid motion.

• Set engine idle at maximum RPM for best performance.

• Allow engine to run a few moments before engaging blades.

STOPPING

• Bring cutter to a complete stop.

• Disengage mower blade.

• Reduce engine idle speed, and allow engine to run momentarily for cooling.

• Place transaxle in the “NEUTRAL” position.

• Turn key to the “OFF” position.

• Remove keys to avoid irresponsible usage.

CUTTER HEIGHT ADJUSTMENT

• There are two height settings; 3.5” AND 4.5”.

• Place two 6” wooden blocks under the deck on the side being adjusted.

• Remove nuts and bolts from the side runner.

• Slide runner down to the other position.

• Replace the nuts and bolts making certain they tightened securely.

• Repeat for the other side. Runners should be at the same height.

BREAKING IN YOUR CUTTER

• Start engine properly.

• Slowly, engage blade control.

• Under supervision, allow blade to rotate and engine to idle for 5 minutes.

• Disengage blade.

• Shift through each gear. While in each gear engage the “GROUND CONTROL” and

travel 20 yards to ensure transaxle works properly.

BEGIN CUTTING

• Make sure area is clear of all bystanders.

• Make sure that all guards, belt guides, and the spark plug wire are properly attached.

• Start engine, set desired engine speed.

• Slowly, engage blade.

• Move transaxle into low gear and activate “GROUND CONTROL” bail.

• Turning is done by rotating the handles left or right. This machine has significant

weight and may take more effort to turn than one may expect. Turning could take

practice.

BACKING UP

• Disengage blade.

• Check safety behind you.

• Move transaxle into “REVERSE” position.

• Activate “GROUND CONTROL” bail.

TRANSPORTING

• Disengage blade.

• Shut off engine and remove keys.

• Using 3 persons to lift cutter is recommended.

• Secure in place while unit is being transported.

• Unit should be left in low gear to avoid any slight rolling.

SUGGESTED PRACTICES

• Always operate engine at full throttle when cutting to assure the best cutting

performance and proper discharge of material.

• If grass is wet, allow it to dry. Wet grass clumps will collect on the bottom of the

deck.

• Go slow when cutting dense areas. Some dense areas may need to be gone over

twice. Better results occur if the second cut is 90 degrees to the first cut.

BEFORE EACH SEASON

A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run

better and last longer.

• Replace the spark plug.

• Clean or replace the air filter.

• Check blades and belts for wear.

BEFORE EACH USE

• Check engine oil level. (Do this twice to ensure an accurate reading.)

• Check condition of air filter and clean or replace if necessary.

• Check blade operation.

• Check for loose fasteners.

DAILY MAINTENANCE

Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.

Keep blades sharp. Observe all safety precautions.

BLADE CARE AND SERVICE

For best results cutter blades must be kept sharp. The blades can be sharpened with a few

strokes of a file or grinding wheel. Do Not attempt to sharpen while on the cutter.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are

tight.

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged. Order by part number from

Swisher Mower and Machine Co. Inc.

OD39--SWISHER FLAG DECAL

OD55--DANGER DECAL OD45--WARNING DECAL

OD99--OFF/RUN DECAL

OD29--DANGER DECAL

OD83--RN1234 Shift Decal

OD84--Neutral Lock Decal

DECALS NOT SHOWN

OD85--Predator LH Decal

OD86--Predator RH Decal

OD9BS-04--Briggs 9hp Decal

OD71--New Serial # Decal

OD87--Rugged Cut 24 4SP Trans White Decal

OVERALL ASSEMBLY

SEE DETAIL

PAGE 10

SEE DETAIL

PAGE 11

SEE DETAIL

PAGE 13

SEE DETAIL

PAGE 11

SEE DETAIL

PAGE 13

13 10

SEE DETAIL

PAGE 12

When ordering replacement parts

* = USE PAINT CODE:

TC=TEX.RED,S=SILVER,TK=TEX.BLACK

Item # Description Part #

1 #14 X 3/4 HX Tek Screw ZP NB161

2 Front Cover 2418TC

3 5/16-18 X 3/4 Serr. Flng Bolt NB596

4 5/16-18 Serr. Flng Nut NB170

5 Motor Base Weldment 2450TC

6 5/16 USS Flat Washer ZP NB556

7 5/16-18 X 2 1/2 HCC GR5 ZP NB138

8 Walk Behind Handle 2402TK

9 1/4-20 X 1 1/4 HCC GR5 ZP NB560

10 1/4-20 Nylok Nut NB180

11 Upper & Lower Bail Assembly 4296TK

Drive Bail Assembly 4291TK

Blade Bail Assembly 4294TK

12 1/4-20 X 2 1/2 Flange Bolt NB208

13 Latching Drive Control 4295

14 Transmission Cable 2432

ENGINE-PULLEY ASSEMBLY

BELT

CONFIGURATION

WIRING

CONFIGURATION

513

314

Goes in Rear

Mounting Hole

NOT ACTUAL ENGINE

USED (REF. ONLY)

Item # Description Part #

1 5/16-18 X 1 1/4 Serr. Flange Bolt NB253

2 5/16-18 Serr. Flange Nut NB170

3 5/16 USS Flat WasherZP NB556

4 5/16-18 X 2 1/4 Serr.Flange GR5 ZP NB622

5 Belt Guide 2413

6 Engine PulleySpacerLong 1.5" 689L

7 Engine Pulley- 2.5" 2411

8 1/4 X 1/2 KeyStock 4258

9 1 X 1 1/2 10GA Washer NB614HT

10 Engine Pulley- 4.25"OD,1 1/4 ID BB105

11 Washer Belleville 699

12 7/16-20 X 1 1/2 HCF GR5 ZP NYLOC NB637

13 Transmission Belt-32" 2414

14 5/16-18 X 3 1/2 Carriage Bolt NB517

15 Engine B&S Recoil St W/Gas Tank N/A

16 1/4-20 X 3/4 GR5 ZP NB250

17 Belt Guide Weldment 2451TK

18 1/4-20 Flange Nut NB524

SSB

9113

When ordering replacement parts

* = USE PAINT CODE:

TC=TEX.RED,S=SILVER,TK=TEX.BLACK

2470 2471

KSM

BROWN

RED

GREEN

2472

BROWN

6114 – BLADE PULLEY

Otros manuales para Predator WB924

Otros manuales de Cortacésped de Swisher

Swisher

Swisher T11544A Manual de usuario

Swisher

Swisher ST60022 Manual de usuario

Swisher

Swisher ST60022Q Manual de usuario

Swisher

Swisher POL10544C Manual de usuario

Swisher

Swisher WBERC11524 Manual de usuario

Swisher

Swisher QUADBOSS QBT14560A Manual de usuario

Swisher

Swisher ZT1436B, ZT18542, ZT2250 Manual de usuario

Swisher

Swisher ZT2760B Manual de usuario

Swisher

Swisher T1260, T1360, T1460 Manual de usuario

Swisher

Swisher QUADBOSS QBFC14560 Manual de usuario

Swisher

Swisher WBRC11524XP Manual de usuario

Swisher

Swisher ZT2452 Manual de usuario

Swisher

Swisher ZT2454A Manual de usuario

Swisher

Swisher FC14560CL Manual de uso y cuidado

Swisher

Swisher POL10544C Manual de usuario

Swisher

Swisher ZT2866 Manual de usuario

Swisher

Swisher FC11544BS Manual de usuario

Swisher

Swisher FC11544CL Manual de usuario

Swisher

Swisher QBT2066 Manual de usuario

Swisher

Swisher ZT2454 Manual de usuario

Swisher

Swisher FC11544BSXP Manual de usuario

Swisher

Swisher ST50022STDQ Manual de usuario

Swisher

Swisher T1260, T1360, T1460 Manual de usuario

Swisher

Swisher WB11524BS Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario