Swisher WB11524BS Manual de usuario

THE PREDATOR

THE PREDATORTHE PREDATOR

THE PREDATOR

2424

24”

””

” WALK BEHIND

WALK BEHIND WALK BEHIND

WALK BEHIND

ROUGH CUT

ROUGH CUTROUGH CUT

ROUGH CUT

OWNER’S

MANUAL

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE (660) 4 -8183 FAX (660) 4 -8650

MODEL NO.

Operation

Service and Adjustment

Repair Parts

Made In The

USA

REV 12-341

WB11524BS

swisherinc.com

10 50

STARTING SERIAL #:

L112-341001

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

Meijer.com

In the event you have a claim unde this wa anty, you must etu n the p oduct to an autho ized

se vice deale . All t anspo tation cha ges, damage, o loss incu ed du ing t anspo tation of pa ts

submitted fo eplacement o epai unde this wa anty shall be bo ne by the pu chase . Should you

have any questions conce ning this wa anty, please contact us toll-f ee at 1-800-222-8183. The

model numbe , se ial numbe , date of pu chase, and the name of the autho ized Swishe deale f om

whom you pu chased the mowe will be needed befo e any wa anty claim can be p ocessed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages o limitations on how long an implied wa anty may

last, so the above limitations o exclusions may not apply to you. This wa anty gives you specific

legal ights and you may have othe ights, which va y f om state-to-state. This is a limited wa anty

as defined by the Magnuson-Moss Act of 1975.

LIMITED WARRANTY

The manufactu e ’s wa anty to the o iginal consume pu chase is: This p oduct is f ee f om defects

in mate ials and wo kmanship fo a pe iod of (1) yea f om the date of pu chase by the o iginal

consume pu chase . We will epai o eplace, at ou disc etion, pa ts found to be defective due to

mate ials o wo kmanship. This wa anty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY..……………………….3-4

PRE-OPERATING..….……..……4

OPERATION.……………………….5-7

DECALS…..………….……………….8

PARTS BREAKDOWN…………….9-13

SAFE SLOPE GUIDE..………………15

1) Engine Wa anty All engines utilized on ou p oducts have a sepa ate wa anty extended

to them by the individual engine manufactu e . Any engine se vice

difficulty is the esponsibility of the engine manufactu e and in no

way is Swishe o its agents esponsible fo the engine wa anty. The

B iggs & St atton Engine Se vice Hot-Line is 1-800-233-3723.

2) Comme cial Use This p oduct is not intended fo comme cial use and ca ies no

comme cial wa anty.

3) Limitation This wa anty applies only to p oducts which have been p ope ly

assembled, adjusted, and ope ated in acco dance with the inst uctions

contained within this manual. This wa anty does not apply to any

p oduct of Swishe that has been subject to alte ation, misuse, abuse,

imp ope assembly o installation, shipping damage, o to no mal wea

of p oduct.

4) Exclusions Excluded f om this wa anty a e no mal wea , no mal adjustments, and

no mal maintenance.

Meijer.com

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you fo choosing Swishe ’s 24” Walk Behind Rough Cut. Befo e

ope ating you Walk Behind, please ead, unde stand and follow all of the safety

p ecautions and othe inst uctions explained in this manual. As with all powe

equipment, lawn mowe s can be potentially dange ous if not p ope ly used.

• Read the manual. Lea n to ope ate this machine safely.

• Always disconnect the spa k plug wi e and place the wi e whe e it cannot contact the

spa k plug, to p event accidental sta ting the engine when setting up, t anspo ting,

adjusting o making epai s.

• Keep all shields and gua ds in place.

• Unde stand the speed, stee ing and stability of this machine. Know the positions and

ope ations of all cont ols befo e you ope ate this machine. Check all of the cont ols in

a safe a ea befo e sta ting to wo k with this machine.

• Allow only esponsible adults who a e familia with these inst uctions to ope ate this

machine. Never allow children to operate this machine.

• Clea the a ea of objects such as ocks, toys, wi e, etc. that can be picked up and

th own by the blade.

• Be su e the a ea is clea of othe people befo e mowing. Be awa e of the mowe

discha ge di ection and do not point at anyone. Stop the machine if anyone ente s the

mowing a ea. Child en a e often att acted to the machine and the mowing activity.

Never assume that children will remain where you last saw them. Keep child en

unde the watchful ca e of anothe esponsible adult.

•No riders!

• Do not put hands o feet nea o unde otating pa ts.

• Do not mow in eve se. Always look down and behind before and during backing.

Meijer.com

• Tu n off the blade when not mowing. Befo e leaving the machine, tu n off the blade

and stop the engine.

• Watch fo t affic when ope ating nea o c ossing oadways.

• Do not ope ate the mowe if it has been d opped o damaged in any manne o if the

mowe vib ates excessively. Excessive vib ation is an indication of damage. Repai mowe

as necessa y.

• D ess p ope ly. Do not ope ate the mowe when ba efoot o wea ing open sandals. Wea

only solid shoes with good t action when mowing.

• Neve allow ope ation by unt ained pe sons.

• Do not ope ate the machine while unde the influence of alcohol o d ugs.

• Do not ope ate on slopes g eate than 15 deg ees.

• Neve tampe with safety devices. Check thei p ope ope ation egula ly.

• Stop and inspect the equipment if you st ike an object. Repai , if necessa y, befo e

esta ting. Neve make adjustments o epai s with the engine unning.

• Mowe blades a e sha p and can cut. W ap the blades o wea gloves, and use ext a

caution when se vicing them. Do not ope ate at too fast a ate.

• Disengage spa k plug wi e and place whe e it cannot make a connection.

• Check engine oil. All engines a e filled with oil at the facto y. Ve ify oil level and

add if necessa y befo e sta ting engine (See Engine Owne ’s Manual).

• Ve ify fuel level and add if necessa y befo e sta ting engine.

• Reconnect spa k plug wi e.

• Refe to pages 5-7 in this manual fo p ope ope ating p ocedu es.

PRE-OPERATING INSTRUCTIONS

Meijer.com

The ope ation of any mowe can p oduce fo eign objects to be th own into the

eyes, esulting in seve e eye damage. Always wea ce tified safety glasses o

wide-vision safety goggles ove spectacles befo e sta ting any cutting machine and

while ope ating such a machine.

The ope ation of any mowe p oduces sound waves that a e damaging to the

human ea . Ea p otection is ecommended.

CAUTION!

T agic accidents can occu if the ope ato is not ale t to the p esence of

child en. Child en a e often att acted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW WALK BEHIND

INTENDED USE

This is not a lawn mowe . The P edato is designed fo cutting ove g own b ush, weeds,

and othe types of o ganic g owth. This unit is capable of clea ing small saplings of 1.5”

in diamete o less.

PROPULSION

The P edato is self-p opelled and is cont olled by a “GROUND CONTROL” leve . To

engage the d ive, put the t ansaxle in a gea and activate the left leve . Releasing the

leve will disengage the self-p opel.

Unde most conditions cutting should be done in a low gea (1st o 2nd). Uppe gea s

should be used fo conditions whe e weeds and b ush a e thinned out o not as tall. In

confined a eas the machine can be pushed fo wa ds o backwa ds by eleasing the

“GROUND CONTROL” leve , placing the t ansaxle in neut al, and pushing the

machine.

TRAVEL SPEED

Speed can be va ied by choosing a highe o lowe gea using the gea shift leve at the

ea of the machine o by changing the engine speed with the engine th ottle. Do not

adjust speed with the blade engaged. To shift the cutte into eve se, elease “GROUND

CONTROL” leve , disengage blade, and otate the shift leve to the left. When the leve

stops, lift up the eve se lockout latch and continue to move the shift leve to the left until

it stops again. The Predator is equipped with a safety control that will kill the engine

if the blade is engaged while cutter is in the “REVERSE” gear.

ENGAGING BLADE

An “OPERATOR PRESENCE” leve and a “BLADE ENGAGE DRIVE” cont ol wo k

togethe to engage the P edato ’s blade. Both devices must be activated befo e the blade

will wo k. Releasing the “OPERATOR PRESENCE” leve will disengage both the blade

and the “BLADE ENGAGE DRIVE” cont ol.

Meijer.com

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel used.

Engine must be level to accurately check and fill oil. Do not overfill.

• Make sure unit is level, blade is disengaged, and transaxle in NEUTRAL”

• Check spark plug wire, oil level, and fuel level.

• Check all electrical connections for build-up of debris.

• If needed set CHOKE” to choke position.

• Set engine throttle control to ½ throttle position.

• Pull rope with a single fluid motion.

• After engine has started set CHOKE” to RUN” position.

STOPPING

• Bring the Walk Behind to a complete stop.

• Disengage mower blade.

• Reduce engine idle speed, and allow engine to run momentarily for cooling.

• Place transaxle in the NEUTRAL” position.

• Move engine throttle control to OFF” position.

HEIGHT ADJUSTMENT

• Place two 6” wooden blocks under the deck on the side being adjusted.

• Remove nuts and bolts from the side runner.

• Slide skid up or down to preferred position.

• Replace the nuts and bolts making certain they are tightened securely.

• Repeat for the other side. Runners should be at the same height.

BREAKING IN YOUR WALK BEHIND

• Start engine properly.

• Slowly engage blade control.

• Under supervision, allow blade to rotate and engine to idle for 5 minutes.

• Disengage blade.

• Shift through each gear. While in each gear engage the GROUND CONTROL” lever

and travel 20 yards to ensure transaxle works properly.

BEGIN CUTTING

• Make sure area is clear of all bystanders.

• Make sure that all guards, belt guides, and the spark plug wire are properly attached.

• Start engine, set engine throttle control at maximum engine idle speed for best results.

• Allow engine to run a few moments and slowly engage blade.

• Move transaxle into low gear and activate GROUND CONTROL” lever.

• Turning is done by rotating the handles left or right. This machine has significant

weight and may take more effort to turn than one may expect. Turning could take

practice.

BACKING UP

• Disengage blade.

• Check behind you for safety.

• Move transaxle into REVERSE” position.

• Activate GROUND CONTROL” lever.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of

California Public Resource Code Section 444 to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

Meijer.com

TRANSPORTING

• Shut off engine.

• Secu e in place while unit is being t anspo ted.

• Unit should be left in low gea to avoid any slight olling.

SUGGESTED PRACTICES

• Always ope ate engine at full th ottle when cutting to assu e the best cutting

pe fo mance and p ope discha ge of mate ial.

• If g ass is wet, allow it to d y. Wet g ass clumps will collect on the bottom of the

deck.

• Go slow when cutting dense a eas. Some dense a eas may need to be gone ove

twice. Bette esults occu if the second cut is 90 deg ees to the fi st cut.

BEFORE EACH SEASON

A new spa k plug and clean ai filte assu e p ope ai -fuel mixtu e and help you engine un

bette and last longe .

• Replace the spa k plug.

• Clean o eplace the ai filte .

• Check blades and belts fo wea .

BEFORE EACH USE

• Check engine oil level. Do this twice to ensu e an accu ate eading.

• Check condition of ai filte and clean o eplace if necessa y.

• Check blade ope ation.

• Check fo loose fastene s.

DAILY MAINTENANCE

Make su e all nuts and bolts a e tight and cotte pins and etaine sp ings a e secu e.

Keep blades sha p. Obse ve all safety p ecautions.

BLADE CARE AND SERVICE

Fo best esults blades must be kept sha p. The blades can be sha pened with a few st okes of a

file o g inding wheel. Do Not attempt to sha pen blades while they a e on the machine.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are

tight.

Meijer.com

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged. O de by pa t numbe f om Swishe .

OD39--SWISHER FLAG DECAL

OD55--DANGER DECAL OD45--WARNING DECAL

OD83--RN1234 SHIFT DECAL

10749--REVERSE LOCK DECAL

DECALS NOT SHOWN

OD85--P edato LH Decal

OD86--P edato RH Decal

OD87--Rugged Cut 24 4SP T ans White Decal

OD99112—LARGE LOGO WHITE DECAL

Meijer.com

OVERALL ASSEMBLY

When o de ing eplacement pa ts

*USE PAINT CODE: TK=BLACK

Item # Description Part #

1 Cover - Belt 10682*

2 Bolt - Serrated Flange 5/16-18 X 3/4 NB596

3 Nut - Serrated Flange 5/16-18 NB170

4 C annel - Rig t Side 10676*

5 C annel - Left Side 10677*

6 Clip - Tinnerman 5/16-18 3706

7 Bolt - Serrated Flange 5/16-18 X 2 1/4 NB622

Meijer.com

ENGINE-PULLEY ASSEMBLY

BELT

CONFIGURATION

WIRING

CONFIGURATION

Goes in Rea

Mounting Hole

NOT ACTUAL ENGINE

USED (REF. ONLY)

Item # Description Part #

1 Motor Plate 10678*

2 5/16-18 Serr. Flange Nut NB170

3 5/16-18 X 3/4 Serr. Flange Bolt NB596

4 Belt Retention Weldment 10767

5 Engine Pulley Spacer 1.75" Long BB105S

6 1/4 X 1/2 Key Stock 4258

7 Engine Pulley- 2.5" 2411

8 1 X 1 1/2 10GA Was er NB614HT

9 1/4 X 1 Key Stock 9031

10 Engine Pulley- 4.25"OD,1 1/4 ID BB105

11 Was er, Front W eel (Heat Trtd) TR150W

12 Was er Belleville 699

13 7/16-20 X 1 1/2 HCF GR5 ZP NYLOC NB637

14 3/8-16 X 1 1/2 HCCG NB107

15 3/8 SAE Was er NB272

16 Idler Pulley OD-2.16", ID-3/8" B27

17 3/8-16 2 Way Locking Nut NB280

18 3/8-16 X 1 GR5 ZP Bolt NB604

19 Idler Bus ing 6037

20 Idler Arm 10671*

21 1/4-20 X 3/4 GR5 ZP Bolt NB250

22 1/4-20 Serr. Flange Nut NB524

23 Spring T2SM

24 5/16-18 X 1 1/4 Serr. Flange Bolt NB253

25 Transmission Belt-33" 690

26 Engine B&S Recoil St W/Gas Tank N/A

27 Transmission Cable 2432

SSB

9113

10765

BROWN

2472

BROWN

6114 – BLADE PULLEY

Impo tant: Sp ing

must be hooked in

Idle A m as shown

Install T ansmission Cable Item

#27 in Idle A m befo e installing

Idle A m to Moto Plate

2410

TRANSAXLE PULLEY

690 – TRANSAXLE BELT

TOP ENGINE PULLEY

CONFIGURATION

B2 – TRANSAXLE IDLER PULLEY 2411 – TOP ENGINE PULLEY

BB105 – LOWER ENGINE PULLEY

T30V – V-BELT PULLEY

B52 – BLADE IDLER PULLEY

BA50 – BLADE ENGAGEMENT BELT

BOTTOM ENGINE PULLEY CONFIGURATION

ATTACH TO

MAGNETO

NOTE: WIRES MUST PASS THROUGH ALL WIRE GUIDES POSSIBLE

When o de ing eplacement pa ts

*USE PAINT CODE: TK=BLACK

Meijer.com

Tabla de contenidos

Otros manuales de Cortacésped de Swisher

Swisher

Swisher ZT2452A Instrucciones de funcionamiento

Swisher

Swisher ST60022 Manual de usuario

Swisher

Swisher PST67522A Manual de usuario

Swisher

Swisher ST67522BS Manual de usuario

Swisher

Swisher FT1150 Manual de usuario

Swisher

Swisher Commercial Pro Response Z21554CPHO Manual de usuario

Swisher

Swisher POL1250F Manual de usuario

Swisher

Swisher PREDATOR TALON WBRC11524C Manual de usuario

Swisher

Swisher ST50022STDQ Manual de usuario

Swisher

Swisher QBT2066 Manual de usuario

Swisher

Swisher POSTMASTER PST67522 Manual de usuario

Swisher

Swisher PST5022 Manual de usuario

Swisher

Swisher POL 14560B Manual de usuario

Swisher

Swisher WBERC11524 Manual de usuario

Swisher

Swisher WBRC11524XP Manual de usuario

Swisher

Swisher ZT2350 Manual de usuario

Swisher

Swisher T14560A Manual de usuario

Swisher

Swisher Predator WB80024 Manual de usuario

Swisher

Swisher WB11542F Manual de usuario

Swisher

Swisher ZT2760 BP Manual de usuario

Swisher

Swisher FC10544CL Manual de usuario

Swisher

Swisher Trim-N-Mow Plus STS67522BS Manual de usuario

Swisher

Swisher T1260F Manual de usuario

Swisher

Swisher FC11544CL Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario