Swann Xtreem Manual de usuario

Xtreem®Security Camera

Cámara de seguridad Xtreem®

Caméra de sécurité XtreemMD

Telecamera di sicurezza Xtreem®

Xtreem®Überwachungskamera

EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide

IT Guida rapida DE Schnellstartanleitung

CAMERA OVERVIEW

Passive infrared

motion sensor

Threaded mounting hole

(for optional screw-in stand accessory)

Pull rubber cover gently from the

bottom to access:

- Set (mini) button

- Reset button

- microSD card slot

LED indicator

Set button

Night detection

sensor

Micro USB

charging port

Speaker

QR code

(for device pairing)

Microphone

Remove protective film covering the front of

the camera before use

Note: Keep the top and bottom rubber covers closed when

not in use to prevent water and dust from getting in.

Infrared LEDs

(for night vision)

GETTING STARTED

Before using the camera for the first time, charge it for at least two hours with the included micro USB

charging cable.

1Lift the rubber cover of the micro USB port on the bottom of the camera.

2Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.

3Insert the larger end of the micro USB charging cable into a USB wall charger such as the USB

power adapter that came with your smartphone.

4The LED indicator on the front of the camera turns solid blue indicating that the camera is

charging. When the camera is fully charged, the LED indicator will turn off.

5Actual charging times may vary depending on the USB power supply (DC5V 2.1A is recommended

for faster charging) and the remaining battery level. A full charge may take up to 11 hours (due to

the camera’s large battery capacity).

Note Once you have set up your camera, you can easily track the charging progress (%) using the app.

A microSD card is required for the camera to record events. Depending on the model purchased, your

camera will come with a pre-installed 16GB or 32GB microSD card. You can easily replace the microSD

card with a new one (up to 128GB, minimum Class 10 recommended) if needed in the future. Simply lift

the rubber cover on the top of the camera, eject the current microSD card (push in until it clicks) from

the microSD card slot and then replace with another microSD card (with the label side facing the back

of the camera). Format any microSD card being used with the camera for the first time using the app.

Charging the camera

Installing the microSD card

GET THE SWANN SECURITY APP

1Download the latest version of the Swann Security app from the Apple App Store® or Google

Play™ Store on your iOS or Android device. Simply search for "Swann Security".

2Open the app and create your Swann Security account by tapping “Not yet registered? Sign

Up” at the bottom of the screen. Then, activate your Swann Security account by confirming the

verification email that is sent to the registered email address.

Launch the Swann Security app and sign in. Tap the Pair Device button on the screen (or tap the menu

icon in the top left and select “Pair Device”) and follow the in-app instructions to set up your new

camera. Before you begin, have the camera with you, be close to your router, and have your Wi-Fi

network information (including password) handy. Please note that the camera can connect to a 2.4GHz

Wi-Fi network only.

SET UP THE CAMERA

The camera can be conveniently placed on a table or shelf, or mounted on the wall using the magnetic

stand (supplied) or the screw-in stand (optional accessory which can be purchased separately). Because

the camera is completely wire-free, you’ll have a lot of flexibility on where you can put it. Choose a

location with strong, reliable Wi-Fi reception to ensure best video streaming and battery performance.

As a general rule, the nearer your camera is to your router, the better the wireless connection quality.

CAMERA PLACEMENT

C. With double-sided mounting tape (For indoor use only)

Do not use on rough surfaces. Works best on smooth, dry surfaces (use rubbing alcohol

to clean surface, making sure it is cleared of any dirt).

Peel off liner on one side of the supplied mounting tape and apply it to the back of the

magnetic stand.

Peel off opposite liner then using a firm amount of pressure, press the magnetic stand

against the surface for 60 seconds. Allow 24 hours for the adhesive to fully cure before

attaching the camera onto the magnetic stand.

Mounting the magnetic stand

A. With screws (Recommended method

for permanent mounting)

Remove the rubber pads to reveal screw

holes. Then attach the magnetic stand to

the surface using supplied screws (2.8mm x

21.6mm) and plugs (if mounting on drywall

or concrete). Reinsert the rubber pads.

B. With keyhole slot

There is a keyhole slot on the

back of the magnetic stand

where a screw fits for hanging

on the wall. Insert screw (4mm

x 18.2mm) and plug (if mounting

on drywall or concrete) into the

mounting point, leaving a bit

of gap between the wall and

the screw head. Then fit the

magnetic stand over the screw

head through the keyhole slot

and slide down to make sure it

sits securely.

IMPORTANT: Ensure that the surface and fixing points

are strong enough to sustain the weight of the camera

and magnetic stand.

Have questions?

Visit our Support Center at support.swann.com.You can register your product for dedicated technical

support, find troubleshooting articles, and more. Or email us at any time via: [email protected]

HELP AND RESOURCES

Motion detection

The camera’s PIR motion sensor detects heat signatures of moving objects. You’ll generally get good

detection results by pointing the camera downwards at an angle where people will be moving across

the coverage area before heading directly towards the camera. You can turn motion detection on or off,

as well as adjust the sensitivity using the Swann Security app.

LED indicator guide

The LED light on the front of your camera helps inform you of what is happening with the device.

Swann Security app manual

While using the Swann Security app, you can access the Swann Security app manual (Menu > User

Manual) at any time to learn more about using the app to view live video, playback event clips as well

as customize various camera settings including camera name, sleep period, and motion sensitivity.

Rebooting the camera

On rare occasions, it might be necessary to reboot your camera if it becomes unresponsive. A simple

reboot can also fix connectivity issues quickly. Using a paper clip, press and release the Reset button.

This powers off the camera. Then briefly press the SET button (for 1 second) to reboot the camera.

Solid Blue USB Charging

Solid Red Live streaming / Motion recording

Slow Blinking Blue Wi-Fi Pairing mode

Fast Blinking Blue Connecting to Wi-Fi

Infrared LEDs Blinking Firmware update in progress

Otros manuales para Xtreem

Tabla de contenidos

Otros manuales de Cámara de seguridad de Swann

Swann

Swann NHD-805 Manual de usuario

Swann

Swann Dummy PIR Camera Manual de usuario

Swann

Swann NHD-815 Manual de usuario

Swann

Swann SwannOne SoundView SWO-SV02K Manual de usuario

Swann

Swann PRO-680 Manual de usuario

Swann

Swann SWIFI-FLOCAM2 Manual de usuario

Swann

Swann MaxiBrite SW212-MXB Manual de usuario

Swann

Swann PRO-771 Dome Manual de usuario

Swann

Swann SW322-XDW Manual de usuario

Swann

Swann SwannOne SoundView SWO-SV02K Manual de usuario

Swann

Swann Digital EagleEye ADW-400 Manual de usuario

Swann

Swann Cloud Manual de usuario

Swann

Swann Security Camera Manual de usuario

Swann

Swann IP3G1000 Manual de usuario

Swann

Swann PTZ INTERNAL Speed Dome Manual de usuario

Swann

Swann Enforcer Manual de usuario

Swann

Swann NVW-800CAMT Manual de usuario

Swann

Swann OutdoorCam none Manual de usuario

Swann

Swann Professional CCTV Camera Manual de usuario

Swann

Swann Security Cam Color Video Camera Manual de usuario

Swann

Swann SW223-SPR Manual de usuario

Swann

Swann Pro-752 Dome Manual de usuario

Swann

Swann D-Cam Manual de usuario

Swann

Swann SWIFI-2KOCAM-EU Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario