Swann SWIFI-4KFLOCAM-US Manual de usuario

4K Floodlight Security Camera

Cámara 4K de seguridad con Reflector

EN QUICK START GUIDE

ES GUÍA DE INICIO RÁPIDO

Model: SWIFI-4KFLOCAM-US

IMPORTANT SAFETY INFORMATION

• INSTALL THE PRODUCT IN ACCORDANCE WITH LOCAL AND NATIONAL ELECTRICAL CODES.

IF YOU HAVE ANY DOUBTS OR QUESTIONS ABOUT THE ELECTRICAL CONNECTIONS OR IF

YOU NEED AN ELECTRICAL JUNCTION BOX INSTALLED, CONSULT A LICENSED ELECTRICIAN.

IN CERTAIN JURISDICTIONS, THIS PRODUCT NEEDS TO BE INSTALLED BY A LICENSED

ELECTRICIAN. CHECK WITH LOCAL AUTHORITIES FOR APPLICABLE REQUIREMENTS.

• THE PRODUCT MUST BE MOUNTED ON A FLAT SURFACE CAPABLE OF SUPPORTING THE FULL

WEIGHT OF THE PRODUCT.

• ENSURE THE VOLTAGE MARKED ON THE PRODUCT IS THE SAME AS THE ELECTRICAL POWER

SUPPLY TO BE USED.

• DO NOT CONNECT TO A DIMMER SWITCH OR TIMER.

• ALWAYS TURN OFF ELECTRICAL POWER AT THE MAIN CIRCUIT BREAKER OR FUSE BOX BEFORE

WIRING FIXTURE TO THE POWER SUPPLY. FAILING TO DO SO COULD RESULT IN SERIOUS

INJURY, ELECTRICAL SHOCK, AND/OR RISK OF FIRE.

• DO NOT RELY ON THE WALL SWITCH ALONE TO TURN OFF THE POWER.

• DO NOT OPEN OR DISASSEMBLE THE PRODUCT. THERE ARE NO USERSERVICEABLE PARTS

INSIDE.

CAUTION: RISK OF ELECTRIC SHOCK

CAMERA OVERVIEW

FRONT VIEW SIDE VIEW

QR code

(for device pairing)

Night detection

sensor

Passive infrared

motion sensor

Microphone

(bottom)

LED indicator

Infrared LEDs

(for night vision)

Speaker

Adjustable camera head

Adjustable floodlights

(with brightness control via app)

Rear

Pull rubber cap gently from the bottom to access:

• Reset (Pair) button

• MicroSD card slot

32GB card pre-installed, Max. 128GB card supported

• Before you permanently mount the floodlight camera unit, it is important that you confirm the

availability of Wi-Fi as well as the signal strength at the desired installation location.

• Note that Wi-Fi quality can vary significantly at different locations around the home due to

environmental factors such as home construction type and wireless interference from other

electronic devices.

Checking your Wi-Fi network coverage

1Connect your phone to the 2.4GHz Wi-Fi network band of your internet/broadband router.

Note: The camera can connect to a 2.4GHz network only.

2Bring your phone to the location where you want to install the floodlight camera unit. If you have

Wi-Fi connection on your phone, the camera will also likely be able to obtain Wi-Fi connection.

Check the Wi-Fi signal strength status icon at the top of your phone screen. We recommend a

minimum of 1 bar showing as shown below. Further testing should be performed if the Wi-Fi

signal strength is only a single bar.

GETTING STARTED

Wi-Fi Coverage Availability

0 1

Wi-Fi signal strength icon

ExcellentGoodFairPoorNo connection

2 3 4

3To avoid any potential Wi-Fi connection issues later, try playing a video through a media streaming

service app, for example, YouTube™or Netflix™, on your phone. If possible, temporarily pause all

GETTING STARTED

Replacing the MicroSD card

The camera comes with a pre-installed 32GB microSD card which is required for recording events

and performing firmware updates. You can easily replace it with any compatible microSD card (up to

128GB, minimum Class 10 recommended). Make sure to format any microSD card the first time you

use it with the camera. Go to the device’s Advanced Settings screen in the app and select Format.

online activities including gaming and video streaming on all other devices that are connected to

your network while testing is performed, as this can affect the connection speed and quality.

4If you don't experience any video streaming issues (buffering, stuttering, etc), you can proceed

with the installation of the unit. There are also Wi-Fi surveying and speed tools (for example,

www.speedtest.net) available online that can help you analyze and test the quality of your Wi-Fi

network connection such as the download and upload speeds (minimum internet upload speed of

4Mbps is recommended for optimal video streaming).

5If you still have any concerns about your Wi-Fi coverage, consult a licensed electrician about

connecting the floodlight wires to a temporary plug and running an extension cord to a wall

outlet. This will enable you to power the camera on-site and directly test Wi-Fi pairing and live

streaming with the Swann Security app.

Improving your Wi-Fi network signal

• If you're getting a weak Wi-Fi signal or you can’t connect to Wi-Fi at all on your phone at the

installation site, we recommend moving your router closer, installing a Wi-Fi extender (which can

help improve signal reception) or selecting another location.

• Do not proceed with the installation of this unit until you have thoroughly tested and confirmed the

availability and reliability of the Wi-Fi connection at your desired installation location.

INSTALLATION INSTRUCTIONS

FRO N T

FRON T

Mounting strap

Mounting bracket

(pre-assembled)

Screw cap

Wire nut Mounting screw hole

Ensure enough clearance to adjust floodlight

heads for correct beam angle

Live

Neutral

Black

White

Floodlight power wiring

If wiring colors from the junction box do not match —

a common issue in older homes — contact a licensed

electrician who will be able to help you check and

identify the electrical wiring. Do not guess the wires. Incorrect

wire connection will damage the unit and could cause fire or injury.

Notes

• The unit can also be mounted on the ceiling (e.g., under eaves).

• If you need a new junction box, you can purchase one appropriate for

the installation site at your local electrical hardware store.

• If you have any doubts or questions about the electrical connections

or if you need help with the installation of a junction box, consult a

licensed electrician.

Junction box

(not included)

INSTALLATION INSTRUCTIONS

IMPORTANT! TURN POWER OFF AT CIRCUIT BREAKER OR FUSE BOX.

CAUTION: BEFORE HANDLING ANY WIRING, USE A CIRCUIT TESTER TO CONFIRM THAT POWER IS OFF.

When installing the unit, refer to the installation diagram on the previous page.

1If you're replacing an old floodlight unit, disassemble it along with any existing mounting

bracket from the junction box and disconnect the wire connections.

2The floodlight camera unit's mounting bracket comes pre-assembled. Remove both the screw

cap and the mounting bracket screw

to separate the mounting bracket.

3Fix the mounting strap (supplied) to the junction box using two mounting screws B (three sets

of different screw types supplied) that best fit your junction box. The side of the mounting strap

marked "FRONT" should be facing out.

4Connect the junction box and floodlight wires using the wire nuts (supplied). Use the color code

of the wires to match correct connections, as shown in the installation diagram.

5Once the wires are connected, carefully tuck them into the junction box.

The floodlight camera unit is designed to be mounted on a standard wiring junction box and requires

connection to a 100-240VAC power supply. For optimum results, install the unit at least 8 feet (2.4m)

above the ground.

NOTE: BEFORE MOUNTING, ENSURE THE INSTALLATION LOCATION IS WITHIN RANGE OF YOUR CURRENT WI-FI SIGNAL.

SEE "GETTING STARTED" ON PAGES 4-5 FOR INFORMATION ON HOW TO CHECK WI-FI COVERAGE.

(continued next page)

INSTALLATION INSTRUCTIONS

6Position the mounting bracket on the junction box, insert the mounting bracket screw Dwith

washer Cthrough the mounting bracket hole into the center hole of the mounting strap and

tighten the mounting bracket screw to secure in place.

7Re-attach the floodlight camera unit to the mounting bracket with the previously removed

mounting screw

. Then insert the screw cap firmly into the mounting screw hole.

8It is recommended that silicone sealant (not supplied) be applied around the edge of the

mounting bracket (between the bracket and the surface) to prevent moisture from entering the

junction box.

9Restore power at the circuit breaker/fuse box and allow the floodlight camera unit to power

up. This can take up to 2 minutes. During power-up, the floodlights will turn on for a brief

moment.

CAUTION: Floodlights are extremely bright. To avoid possible damage to your eyes, do not

stare directly at the floodlights when they are on.

10 Once you hear the camera say “Ready for pairing” and the LED indicator starts blinking blue

slowly, proceed to the Swann Security app to set up the camera with your Wi-Fi network and

link it to your Swann Security account.

TIP If you have a light switch that controls the floodlight camera unit, remember not to turn off the

switch as this will also turn off the unit. The unit needs to be powered at all times to stay connected

to your Wi-Fi. Put a sticker label on the light switch so that people know not to turn it off.

INSTALLATION INSTRUCTIONS

Ceiling MountedWall Mounted

GET THE SWANN SECURITY APP

1Download the latest version of the Swann Security app from the Apple App Store® or Google

Play™ Store on your iOS or Android device. Simply search for "Swann Security".

2Open the app and create your Swann Security account by tapping “Not yet registered? Sign Up” at

the bottom of the screen. Then, activate your Swann Security account by confirming the verification

email that is sent to the registered email address.

GET THE SWANN SECURITY APP

Tabla de contenidos

Idiomas:

Otros manuales de Cámara de seguridad de Swann

Swann

Swann Black Knight Manual de usuario

Swann

Swann EAGLE-EYE S232-WEE Manual de usuario

Swann

Swann Maxi-Brite PNP-150 Manual de usuario

Swann

Swann MicroCam III Manual de usuario

Swann

Swann NHD-856 Manual de usuario

Swann

Swann PRO-series Manual de usuario

Swann

Swann SwannCloud ADS-446 Manual de usuario

Swann

Swann PRO-T891 Manual de usuario

Swann

Swann 4K Ultra HD Security Camera Manual de usuario

Swann

Swann NHD-855 Manual de usuario

Swann

Swann MBC4MPCAM280116E Manual de usuario

Swann

Swann Theft Deterrent Imitation Cam Manual de usuario

Swann

Swann IP3G1000 Manual de usuario

Swann

Swann PRO-770 Manual de usuario

Swann

Swann HD420 Manual de usuario

Swann

Swann DIY Security Cam Manual de usuario

Swann

Swann Max-IP-Cam Manual de usuario

Swann

Swann MicroCam II Manual de usuario

Swann

Swann DIY Security Cams SW216-2DS Manual de usuario

Swann

Swann Enforcer Manual de usuario

Swann

Swann Wireless OutdoorCam SW231-WCX Manual de usuario

Swann

Swann SW223-SPR Manual de usuario

Swann

Swann PRO-605 Manual de usuario

Swann

Swann BulletCam Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario