Swann Enforcer NHD-900BE Manual de usuario
Enforcer™Bullet
Security Camera
4K Ultra HD for NVRs
Instruction Manual
Security Made Smarter
EN
Introduction
Congratulations on the purchase of your Swann En-
forcer™ Bullet Security Camera.
• 4K Ultra HD video with sensor spotlight, siren
plus red & blue flashing lights
• Microphone on camera helps capture extra de-
tail of what’s happening at your property
• True Detect™ Heat & Motion sensing for reli-
able alerts
• Powerful Night2Day™ color night vision
• Works in rain & snow all year round
Important instructions
1. Make sure the camera is fixed correctly and stable
if fastened in place.
2. Never place strain of any kind on the network ca-
ble connection. It’s designed to clip into the Ethernet
port, but it won’t support weight and can be broken.
3. Do not operate if wires and terminals are exposed.
Important Note: All jurisdictions have specific laws
and regulations relating to the use of cameras. Be-
fore using any camera for any purpose, it is the buy-
er’s responsibility to be aware of all applicable laws
and regulations that limit the use of cameras.
About this Manual: The content in this manual is for
information purposes only and is subject to change
without notice. While every effort is made to ensure
that this manual is accurate at the time of printing, no
liability is assumed for any errors occurred.
1
For instructions on how to configure your camera
for motion detection, changing image settings,
and other functions available, please consult the
manual for your NVR. Go to support.swann.com,
search for your model, then download.
Connecting the Camera2
To connect the camera to your NVR, simply connect the supplied Ethernet cable to the LAN connection on the
camera then plug the other end of the cable into one of the camera inputs on the back of your NVR.
Please note: The power connector is provided as an alternative power option if required. Your NVR will
provide power over the Ethernet cable when connected and a separate power adapter is not required.
LAN
CAM7CAM7 CAM5CAM5
CAM8CAM8 CAM6CAM6
CAM3CAM3
CAM4CAM4
CAM1CAM1
CAM2CAM2
WANWANAUDIO OUTAUDIO OUT VGAVGA
48V48V
Ethernet Cable
Power
Mounting the Camera3
The camera can be mounted onto a flat surface using the screws and wall plugs provided. The flat surface must
have sufficient strength to hold the camera.
→ Position the camera in the location you want to mount it, and mark the screw holes on the surface to
position the screws (mounting template included). Then, using the appropriate screws for the flat surface
you’re fixing the camera to, secure the camera in place.
→ If you’re mounting to a wooden surface, screw the camera directly to the surface.
→ If you’re mounting to a masonry surface (bricks, concrete or similar), you’ll need to use wall plugs.
Aiming the camera
1. Loosen both screws (use an Allen Key) to adjust the camera’s
orientation. This enables you to rotate the camera left or right so
no matter what direction or orientation it’s facing, your images
will be the right way up. Tighten each screw to secure it in place.
2. Loosen the screw to tilt the camera up or down. Tighten the
screw to secure it in place.
3. To pan the camera left or right, loosen the screw and position
it accordingly. Tighten the screw to secure it in place.
1
2
3
Fitting the Weather Protector4
The weather protector provides a weather-resistant shield for the camera’s Ethernet connector to prevent
damage from moisture, dust, and other external factors that could interfere with the electrical connection. We
also recommend you seal the joins with electrical tape to ensure a more weatherproof seal.
Camera Ethernet
Connector
RJ45 Connector
Seal Tube
Rubber O-seal Foam Weather Seal
Seal Cap
Ethernet Cable
1. Place the Rubber-O-ring around the Camera
Ethernet Connector.
2. Carefully push the Ethernet Cable through the Seal
Cap and then the Seal Tube.
3. Connect the RJ45 Connector on the Ethernet Cable
to the Camera Ethernet Connector ensuring the
locking tab securely clicks in.
4. Align the lugs inside the Seal Tube to the Camera
Ethernet Connector, then rotate the Seal Tube to
lock it in place. The Rubber O-ring should become
slightly bulged when the Seal Tube has been correctly
connected.
5. Gently open the pre-cut slit of the Foam Weather
Seal and wrap it around the Ethernet Cable between
the Seal Tube and the Seal Cap. Push this into the
Seal Tube until it is almost all the way in.
6. Firmly push the Seal Cap over the end of the Seal
Tube and rotate it clockwise to screw it on to the Seal
Tube. Continue to tighten until the Foam Weather
Seal bulges slightly from the end.
Camera Location Tips5
1. Take into consideration what you want to monitor
and where you’ll get the best view of it.
2. How you’re going to connect the camera to your
monitoring system; remember that cables and con-
nections should be kept out of the weather.
3. How to keep the camera out of harm’s way. We
recommended mounting your camera at an elevated
position.
4. Place your camera as close to the area of inter-
est as practicable. The best position is from about
13ft/4m above looking slightly down, keeping in mind
the details you are looking for.
5. Although the sky looks nice when you look at the
live view from your camera, it is an unlikely direction
for an offender to approach. Make sure your camera
has minimal sky in it as the light in daylight can make
the foreground of the image darker.
6. Think about the most likely way a potential offender
may approach your home, use your camera to give
you the best coverage of these areas.
7. The camera’s casing is resistant to different weath-
er conditions and tampering. It would take an over-
whelming event to damage the housing.
8. The camera is weather and water-resistant but,
prolonged exposure to adverse weather conditions
such as sunlight and excessive moisture can damage
the internal components.
9. Run cables inside a wall cavity or other protected
enclosure, and ensure that all wiring and connectors
are insulated and protected from moisture.
10. Don’t put your cable near live electrical wiring. AC
electricity generates radio noise, which can interfere
with the signal from your camera.
M900BECAMREV1E | © Swann 2022
Helpdesk & Resources
Security Made Smarter
Visit Swann Support Center at support.swann.com. You can register
your product for dedicated customer support, download guides, find
answers to commonly asked questions, and more.
Product Registration Customer Support
Product Manuals Frequently Asked Questions
Support Community
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Cámara de seguridad de Swann
Swann
Swann PRO-530 Manual de usuario
Swann
Swann PRO-754 Manual de usuario
Swann
Swann SwannCloud ADS-446 Manual de usuario
Swann
Swann ADW-300 Manual de usuario
Swann
Swann SW211-STY Manual de usuario
Swann
Swann HD420 Manual de usuario
Swann
Swann C510R Manual de usuario
Swann
Swann MaxiBrite SW212-MXB Manual de usuario
Swann
Swann SwannOne SoundView SWO-SV02K Manual de usuario
Swann
Swann SW322-XDW Manual de usuario
Swann
Swann Dummy PIR Camera Manual de usuario
Swann
Swann Maxi-Brite Cams SW215-2MX Manual de usuario
Swann
Swann SwannEye HD Manual de usuario
Swann
Swann MBC4MPCAM280116E Manual de usuario
Swann
Swann SWPRO-1080FLB Manual de usuario
Swann
Swann SWIFI-PTCAM2 Manual de usuario
Swann
Swann SW322-XDW Manual de usuario
Swann
Swann Enforcer NHD-900DE Manual de usuario
Swann
Swann SWIFI-ALERTCAM Manual de usuario
Swann
Swann SWCSNO Manual de usuario
