Superbrightleds NDC2K-RGB150 Manual de usuario

Begin the installation, by connecting an appropriate power supply

to the controller. With the controller in standby mode (o󰀨) use the

button to select each setting and buttons to adjust the

setting values to match the table below.

Layout strip near surface of desired application, then hold strip near

mounting surface to determine the total length needed for each section.

See below for cutting instructions and cut o󰀨 any excess strip. Attach

strip using adhesive backing. Then mount controller and power supply

in desired location using included foam tape.

Once controller setting adjustments have been made and components

are mounted, connect strip to provided adapter. With supply power o󰀨,

connect adapter to controller as shown in wiring diagram.

Wiring

Important: Read all instructions prior to installation.

Dream-Color Chasing RGB Strip Kit

• Supports twelve unique IC strip styles and has pixel adjustment from

16 to 2,048 pixels to accommodate di󰀨erent strip lengths.

• Input power should be 5–24 VDC (matching connected strip). Input

power connection is a 5.5 mm / 2.1 mm DC barrel connector.

• Ensure all electrical connections are secure and follow the provided

wiring instructions.

• Strips require data signal to operate properly. Use caution if cutting

strip to custom length as interrupting the data signal will cause the

strip(s) to malfunction. Strips should be powered from a single power

supply connected to the controller, as additional power connections

after the controller will cause the strip(s) to malfunction.

• Jumper wires/interconnects should be no more than 8” between strip

sections to avoid issues with data loss.

• Do not connect components other than those included to the

power supply.

• Do not connect strip or controller directly to AC power.

Safety and Notes

Included Parts

Controller Buttons

Setup and Installation

¹This setting is for the full 5 m strip, part number NDC2-RGB150. Increase

or decrease the pixel count by 1 for each additional 0.1 meter of strip.

Terminal Connection Wire Color for NDC2-RGB150

V- strip negative black

Data strip data green

CLK strip clock blue

V+ strip positive red

Setting Value

IC WS2811

LED Sequence RGB

Pixels¹ 50

ON/OFF button turns the controller on or o󰀨. The controller must

be o󰀨 (powered on in standby mode) to adjust IC type, pixels,

and LED sequence.

Play/pause button can pause and then resume dynamic modes.

Mode increase/decrease buttons cycle up or down to the

next mode. They also adjust IC type, pixel number, and LED

sequence in the settings. M+ and M- perform the same function

on the remote control.

Speed up/down buttons increase or decrease speed during

dynamic modes. S+ and S- perform the same function on the

remote control.

Value selection buttons cycle through di󰀨erent setting types

(IC type, pixel number, and LED sequence) in standby mode.

WIFI-CON

Important: Read all instructions prior to installation. NDC2K-RGB150

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Rev Date: V2 02/03/2020

User Manual

V- V+

(Included LC4M-PT

connector)

D C

3 - Double-Sided Foam Pad (3M-FTP)

1 - Flathead Screwdriver (SDF-G2)

1 - LC4 Locking Connector to Pigtail (LC4M-PT)

1 - Controller (RGB-MDC83)

1 - Dream-Color RGB LED Light Strip (NDC2-RGB150)

1 - 12 VDC Power Supply (CPS-12V-60W)

+12V+12V

DINDIN

GNDGND

Modes/Programs

Mode Program

1 Static Red

2 Static Blue

3 Static Green

4 Static Magenta

5Static Yellow

6 Static Cyan

7 Static White

8 Red Chasing / Right

9 Red Chasing / Left

10 Blue Chasing / Right

11 Blue Chasing / Left

12 Green Chasing / Right

13 Green Chasing / Left

14 Red Chasing / Middle to Ends

15 Blue Chasing / Ends to Middle

16 RGB Chasing to Solid / Backward

17 CMY Chasing to Solid / Forward

18 RGB chasing to Solid / Middle to Ends

19 CMY Chasing to Solid / Ends to Middle

20 Seven Color Chasing to Solid / Backward

21 Seven Color Chasing to Solid / Forward

22 Seven Color Chasing to Solid (Backward) and Chasing (Forward)

23 Seven Color Chasing to Solid (Forward) and Chasing (Backward)

24 RGB Color Scan / Forward

25 RGB Scan / Backward

26 CMY Scan / Forward

27 CMY Scan / Backward

28 Seven Color Scan / Forward

29 Seven Color Scan / Backward

30 RGB Scan / Backward Then Flash Once

31 RGB Scan / Forward Then Flash Once

32 Seven Color Scan / Backward Then Flash Once

33 Seven Color Scan / Forward Then Flash Once

34 RGB Flash

35 Seven Color Flash

36 RGB Jump

37 CMY Jump

38 Seven Color Jump

39 GBM Flow / Forward

40 GCM Flow / Backward

41 CMY Flow / Forward

42 CMY Flow / Backward

Mode Program

43 GYCM Flow / Forward

44 GB Alternating

45 GM Alternating

46 Seven Color Flow / Forward

47 Seven Color Flow / Backward

48 Green Comet / Backward

49 Red Comet / Forward

50 Red Comet / Backward

51 Blue Comet / Forward

52 Blue Comet / Backward

53 Green Comet / Forward

54 Magenta Comet / Forward

55 Cyan Comet / Forward

56 Yellow Comet / Backward

57 White Comet / Forward

58 White Comet / Backward

59 Seven Color Comet / Backward

60 Seven Color Comet / Forward

61 RC Gradual Change

62 YR Gradual Change Chasing / Backward

63 N/A

64 MB Gradual Change Chasing / Backward

65 N/A

66 BC Gradual Change Chasing / Backward

67 N/A

68 GY Gradual Change Chasing / Backward

69 N/A

70 CG Gradual Change Chasing/ Backward

71 N/A

72 WR Gradual Change Chasing/ Backward

73 N/A

74 RB Gradual Change

75 RG Gradual Change

76 MR Gradual Change Chasing/ Backward

77 N/A

78 RM Gradual Change

79 RY Gradual Change

80 BC Gradual Change

81 BM Gradual Change

82 GY Gradual Change

83 Scan Modes 1–82

Dream-Color Chasing RGB Strip Kit WIFI-CON

Important: Read all instructions prior to installation. NDC2K-RGB150

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Rev Date: V2 02/03/2020

User Manual

FCC Statement (RGB-MDC83)

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation. Any changes

or modications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Specications (RGB-MDC83)

Model RGB-MDC83

Operating Temperature -4°–140° F (-20°–60° C )

Supply Voltage 5–24 VDC

Maximum Output Power 5 A

Maximum Remote Range¹ 175 ft (53.3 m)

²Range may be decreased by interference from electrical signals and physical barriers

Otros manuales de Equipo de iluminación de superbrightleds

superbrightleds

superbrightleds WP Series Manual de usuario

superbrightleds

superbrightleds STN-2-TW Manual de usuario

superbrightleds

superbrightleds HBU-50K240W Manual de usuario

superbrightleds

superbrightleds WPA-SW Series Manual de usuario

superbrightleds

superbrightleds HLV8 Series Manual de usuario

superbrightleds

superbrightleds USP Series Manual de usuario

superbrightleds

superbrightleds STN-2-COB Manual de usuario

superbrightleds

superbrightleds STN-2-UC Manual de usuario

superbrightleds

superbrightleds STN-3-UC Manual de usuario

superbrightleds

superbrightleds ALKW8-RGB72 Manual de usuario

superbrightleds

superbrightleds EL3-RW Manual de usuario

superbrightleds

superbrightleds STAC Series Manual de usuario

superbrightleds

superbrightleds User Manual Manual de usuario

superbrightleds

superbrightleds FLD-CNL-60005-100W Manual de usuario

superbrightleds

superbrightleds EL2-SW Manual de usuario

superbrightleds

superbrightleds EPLL Series Manual de usuario

superbrightleds

superbrightleds STN-1-RGB Manual de usuario

superbrightleds

superbrightleds DDAL-SW3B Series Manual de usuario

superbrightleds

superbrightleds XSCS-RW Manual de usuario

superbrightleds

superbrightleds FUT Series Manual de usuario

superbrightleds

superbrightleds ALKW9-RGB93 Manual de usuario

superbrightleds

superbrightleds WPG Series Manual de usuario

superbrightleds

superbrightleds LPD Series Manual de usuario

superbrightleds

superbrightleds EL2-CRW Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

superbrightleds NDC2K-RGB150 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas