Suntex CT-6300 Manual de usuario

Setup Cal. Mode Enter

Operation

Manual

CT-6300

Microprocessor

Residual Chlorine/

Ozone

Transmitter

Brief Instruction 1

1. Specifications 2

2. Precautions for installation 3

3. Assembly and installation

3.1 Controller installation 3

3.2 Illustration of panel mounting 3

3.3 Illustration of wall mounting and pipe mounting 4

4. Overview of Residual Chlorine/Ozone Transmitter CT-6300

4.1 Illustration of rear panel 5

4.2 Illustration of terminal function 5

4.3 Description of terminal function 6

4.4 Illustration of cable wiring 6

4.5 Illustration of electrical connection 7

5. Configuration

5.1 Illustration of front panel 8

5.2 Keypad 8

5.3 LED indicators 9

5.4 Display 9

6. Operation

6.1 Measurement mode 10

6.2 Set-up mode 10

6.3 Calibration mode 10

7. Settings

Block diagram of settings 11

7.1 Entry of set-up mode 12

7.2 Security code of settings 12

7.3 Measurement parameter set-up 13

7.4 Temperature set-up 14

7.5 Auto return set-up 14

7.6 Hi point Setting 15

7.7 Lo point Setting 16

7.8 Wash time 17

7.9 Analog output 1 (Residual Chlorine/Ozone) 18

7.10 Analog output 2 (Temperature) 19

7.11 Averaged signal value set-up 20

7.12 Backlight LCD 21

CONTENTS

8. Calibration

Block diagram of Calibration 22

8.1 Security code of calibration 23

8.1.1 Authority of Security Code 23

8.1.2 Security Code Settings 23

8.2 Calibration principle 24

8.3 Current type sensor calibration mode 24

8.4 Voltage type sensor calibration mode 25

8.5 Attention of sensor usage 26

9. Error messages (Error code) 27

10. Maintenance 28

Brief Instruction

Settings of measurement parameters (see chapter 7)

If you like to use security code of settings, the original code is 1111.

Settings of Calibration (see chapter 8)

In the tP output function, please set analog output 2 with or

(

tem

erature

)

In the main measurement output function, please set analogoutputwith or

＋

In measurement mode, pressing “Setup＂and “Mode＂simultaneously

allows you to access Set-up mode.

In the Code function, entering original code or user’s designated code allows you

to reset the code or shut down this function.

In the Configuration function, select Cl2or O3sensor according to the sensor’s model.

In the Temperature function, setup temperature or make temperature correction.

In the Relay 1 function, please select or to activate it or not.

In the Relay 2 function, please select or to activate it or not.

In the Clean function, please set wash time and stop duration.

In the Averaged measurement value function, please set measurement value

numbers for averaged measurement value to increase the stability of reading.

In the Back light function, please set brightness of display and sensitivity of

light-source sensor.

In measurement mode, pressing “Cal.＂and “Mode＂simultaneously

allows you to access Calibration mode.

If you like to use security code of calibration, the original code is 1111.

In the Code function, entering original code or user’s designated code allows you to

reset the code or shut down this function.

In the Auto-return function, activate the auto-return to the measurement mode display if

not press any key in 3 minutes while in the setting mode or calibration mode. .

1.Specifications

Model CT-6300

Measuring modes Residual(Free) Chlorine / Ozone / Temperature

Cl20.00~100.00 ppm(mg/l), depends on which sensor

O30.00~20.00 ppm(mg/l) , depends on which sensor

Ranges

TEMP -10.0~110.0°C

Cl20.01 ppm(mg/l)

O30.01 ppm(mg/l)

Resolutions

TEMP 0.1°C

Cl2±0.5%±1Digit

O3±0.5%±1Digit

Accuracy

TEMP ±0.2°C±1Digit

Temperature

Compensation Automatic with PT-1000 / NTC-30K or manual adjustment

Ambient Temp. 0~50°C

Storage Temp. -10~70°C

Display LCD display with sensitization sensorfor

auto/manual illumination function

Analog output 1 Isolated DC 0/4~20mA corresponding to

residual chlorine/ ozone, max. load 500Ω

Analog output 2 Isolated DC 0/4~20mA corresponding to

temperature, max. load 500Ω

Contact 240VAC, 0.5A Max. (recommend)

Settings Activate Hi/Lo two limited programmable

Contact 240VAC, 0.5A Max. (recommend)

Wash Time ON: 0～9999 sec. / OFF: 0.0～999.9 hours

Voltage output DC±8V , 0.5W Max.

Power Supply 100V~240VAC±10%, 5W Max., 50/60Hz

Installation Wall or Pipe or Panel Mounting

Dimensions 144 mm ×144 mm ×115 mm (H×W×D)

Cut off Dimensions 138 mm ×138 mm (H×W)

Weight 0.82Kg

Certification IP 65 (NEMX 4X)

Wrong wiring will lead to breakdown or electrical shock of the instrument, please read this

operation manual clearly before installation.

zMake sure to remove AC power from the controller before wiring input, output connections,

and remove it before opening the controller housing.

zThe installation site of the controller should be good in ventilation and avoid direct sunshine.

zThe material of signal cable should be special coaxial cable. Strongly recommend using our

coaxial cable. Do not use normal wires instead.

zAvoid electrical surge when using power. Especially when using three-phase power, use

ground wire correctly.

zThe output terminals of the controller are designed for alarm and control function. Due to the

safety and protection concern, please be sure to connect current-sufficient relay to load with,

in order to ensure the operation safety of the instruments.(Please see chapter 3.6--Electrical

connection diagram)

3. Assemblyandinstallation

3.1 Controller installation: This controller can be installed through panel mounting, wall

mounting and pipe mounting.

Installation of panel mounting: First,prepare a square hole of 138 x 138mm on the panel box,

and then insert the controller directly into the panel box. Insert the accessorial mounting

bracket from the rear, and make it be fixed in to pickup groove.

3.2 Illustration of panel mounting:

2. Precautions for installation

138mm

138m

Hole size

＋

42mm

Hole distances on the

anel box

Mounting bracket

Illustration of panel mounting,

fixed with mounting bracket

90mm

3.3 Illustration of Wall mounting and pipe mounting

Installation of pipe mounting

Fixed with U-shaped pipe clip

Order No.: 8-34

Installation of wall mounting

Fixed with 4 x M5 screws

Sun Shield (Pipe mounting)

Order No.: 8-35 and 8-35-1 Sun Shield (Wall mounting)

Order No.: 8-35 and 8-35-2

4. Overview of residual chlorine/ozone transmitter CT-6300

4.1 Illustration of rear panel

4.2 Illustration of terminal function

4/20m

S+

S-

GND

HI LO WASH

POWER

INPUT POWER +

±8V

4/20m

GND

Chlorine/O³

4 wire electrode (voltage type)

Chlorine/O³

2 wire electrode (current type)

4.3 Description of terminal function

4.4 Illustration of cable wiring

Chlorine /O3

2 wire electrode

(

current t

)

PT1000

TC30

T/P SG L1

Chlorine /O3

S+

4 wire electrode

(

volta

e t

)

PT1000

TC30

T/P SG S-

+8 -8

AC100~240V: Power supply terminal

WASH: External wash relay terminal

REL2: External relay terminal Low Point control

REL1: External relay terminal High Point control

4~20mA：Temperature current output terminal, for external recorder or

PLCcontrol

4~20mA：Master measurement current output terminal, for external

recorderorPLCcontrol

DC-8V：Connect to voltage type electrode (CLE2.2) terminal V－(brown wire)

NC: None contact

T/P: Connect to earth end of temperature probe

DC+8V/ L1：Connect to a voltage type electrode (CLE2.2)terminal V＋(green wire),

or connect to a current type electrode(CLE3) terminal 1.

S-: Connect to black signal wire of the voltage type of electrode (CLE2.2)

L2: Connect to terminal 2 of the current type electrode (CLE3)

S+: Connect to white signal wire of the voltage type of electrode (CLE2.2)

g: green wire

br: brown wire

bl: black wire

w: white wire

Wiring of 4 wire electrode

(voltage type) Wiring of 2 wire electrode (current type),

leverage transmitter’s DC ±8V

4.5 Illustration of electrical connection:

Surge absorber

Transmitter

Cleaning device

Dose feeder

100 ~ 240VAC

Surge absorber

External relay

Tabla de contenidos

Otros manuales de Transmisor de Suntex

Suntex

Suntex TC-7310-RS Manual de usuario

Suntex

Suntex CT-6110-POL Manual de usuario

Suntex

Suntex TC-7100 Manual de usuario

Suntex

Suntex EC-4110-I Manual de usuario

Suntex

Suntex TC-7310-RS-M Manual de usuario

Suntex

Suntex PC-3310-RS Manual de usuario

Suntex

Suntex PC-3310 Manual de instalación

Suntex

Suntex PC-3110-RS Manual de usuario

Suntex

Suntex PC-300A Series Manual de usuario

Suntex

Suntex EC-4110 Manual de usuario

Suntex

Suntex PC-3110-P Manual de usuario

Suntex

Suntex IT-8100 Manual de usuario

Suntex

Suntex CT-6300RS Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario