SUNERZHA NUANCE Instrucciones de uso

ASSEMBLY AND OPERATING MANUAL

INSTRUKCJA MONTAŻU I EKSPLOATACJI

STAINLESS STEEL ELECTRIC RADIATORS

GRZEJNIKI ELEKTRYCZNE ZE STALI NIERDZEWNEJ

www.sunerzha.eu

121020

Sunerzha Sp. z o.o.

3 Przemyslowa Street, Pruszcz Gdanski, Poland, 83-000

Tel./fax: +48 58 692 80 88, E-mail: [email protected]

DISTRIBUTOR / DYSTRYBUTOR DISTRIBUTOR / DYSTRYBUTOR

Sunerzha Sp. z o.o.

3 Przemyslowa Street, Pruszcz Gdanski, Poland, 83-000

Tel./fax: +48 58 692 80 88, E-mail: [email protected]

www.sunerzha.eu

1. General Information

Sunerzha electric radiators are designed to dry textiles, mainly towels.

This manual applies to SUNERZHA electric radiator models:

2. Technical Data

2.1. Product made of stainless steel AISI 304.

ATTENTION! PRODUCT DO NOT CONTAIN GALVANIC COATING.

2.2. Power supply – 220-230 V.

2.3. Wattage – 300 W.

2.4. Alternating current – frequency 50/60 Hz.

2.5. Device protection class – Class I.

2.6. Device protection IP – IP44.

2.7. Maximum load – 5 kg.

2.8. Heating is carried out by electric heating element.

2.9. The radiator is filled with heating fluid for autonomous heating and air conditioning systems.

ATTENTION! The device is designed only for drying textiles.

2.10. Possibility of choosing the type of electrical connection: the dryer is equipped with a wire with a

plug and masking rosette to connect with a power supply hidden in a wall.

NUANCE EPATAGE

www.sunerzha.eu

3. Principles of assembly and operation

3.1. The device should be mounted on the wall in a vertical position.

ATTENTION! Due to the safety of children the electric radiator should be mounted so that

its lowest warming part was outside the reach of children, ie. a minimum of 60 cm above

the floor.

3.2. Install the radiator so that the multifunctional control module is located at the bottom.

3.3. Mounting the radiator to the wall is done by telescopic fixings, which allows to adjust the distance

of the product from the wall (fig. 1).

3.4. After the installation of the radiator it is recommended to switch it on after 10-15 minutes.

3.5. Connect the radiator to the power supply.

3.6. The device is ready for work.

3.7 To avoid disappearance of a mirror shine do not use any abrasives. To clean the surface of the

radiator manufacturer recommends a solution of soap and water.

3.8 When operating the electric dryer, follow the general standards for the safety of electrical

equipment.

Perform the bolt assembly

with a wrench

Dowel Wall

Inner pin

Console sleeve

Screw

Binding screw

Technological turnkey hole

Fig. 1

4. Safety requirements

4.1. The radiator must be connected to a earthed power supply.

4.2. Make sure that the cable and plug are not damaged before connecting to the power supply.

4.3. After finishing using the radiator, disconnect the heater from the power supply.

4.4. Do not interfere with the structure of the radiator.

4.5. Do not carry the heater by the electric cable.

4.6. Do not disconnect the radiator from the power supply by pulling the cable.

4.7. Exclude the possibility of access to the radiator for children without adult control, to protect them

from the possible unpleasant effects of contact with the hot surface of the radiator.

4.8. Do not lean on the radiator.

4.9. Do not use the device in a manner inconsistent with its intended use.

www.sunerzha.eu

5. General technical data

5.1. Power supply – 220-230 V.

5.2. Wattage – 300 W.

5.3. Alternating current – frequency 50/60 Hz.

5.4. Device protection class – Class I.

5.5. Device protection IP – IP44.

5.6. Control module:

Control module:

1) electric heating element casing;

2) signalling diodes;

3) rotary control element;

4) power cord.

Fig. 2

5.7. Control and temperature change of the radiator from 40 to 60°C.

5.8. Automatic maintenance of the set temperature.

5.9. Built-in timer function.

5.10. Overheating protection.

5.11. Display of a preset temperature level by individual signaling diodes.

124

www.sunerzha.eu

6. Operating instructions for the control module

6.1. After connecting the power supply, the device switches to the "0" mode.

6.2. Turning the control knob in a clockwise direction allows you to select the following operating

modes:

6.2.1.The "1-5" modes allow the user to set the appropriate product temperature.

6.2.2.The "6-10" modes allow you to set the operation time ("timer"), set the temperature as in "5"

mode (60 °C).

6.2.3.After the set time has elapsed, the unit switches to "0" mode.

6.2.4.In modes "7-10" after finishing each of the set hours the LEDs are switched off in series, the

number of glowing LEDs determines the remaining time of the timer with rounding to the whole

hour.

6.2.5.When in "0" mode, turning the knob counter-clockwise does not cause any changes in the

controller operation.

6.2.6.When in "0" mode, turning the knob in a clockwise direction does not cause any changes in the

controller operation.

6.2.7.To reset any mode or set "0" mode, turn the regulator knob counterclockwise.

After reaching the set temperature, the control module goes into the mode of maintaining

the set thermal parameters, with periodic shutdown from the power supply, which

significantly reduces the consumption of electricity.

Standard modes

Mode

number Description Signalling diodes

(numbering from bottom to top)

Controller off Lights up in blue

01 2 345

Temperature 40°C Lights up red

11 2 345

Temperature 45°C Lights up red

21345

Temperature 50°C Lights up red

3145

Temperature 55°C Lights up red

415

234

Temperature 60°C Lights up red

51 2 345

www.sunerzha.eu

Timer modes

ATTENTION! If the controller is disturbed, the emergency mode is activated.

The blue LED flashes.

7. Guarantee

7.1. The Guarantee for correct operation of the device is granted for a period of 2 years from the date

of sale, if carriage and installation rules are obeyed, the towel warmer is correctly operated and if

the conditions described below are fulfilled.

7.2. The duty of the Customer is to check whether the wrapping is not damaged, what may indicate a

problem with the device at the time of purchase or during transport. Manufacture packaging

defects (damage, wastage, poor quality of the coating, etc..) visible with the naked eye should be

reported by the Customer to the Guarantor within 3 days from reception of the radiator. This kind

of defects reported after installing the devices will not be subject of a complaint.

7.3. Following conditions must be fulfilled to start considering claim:

7.3.1.Filled warranty card (warranty card number, type and serial number of the device, date of sale

and the seller's signature and stamp) along with the invoice of purchase.

7.3.2.Installing the device in accordance to the operating instructions and manufacturer

recommendations without any individual modifications while keeping in mind the standards of

installation and use cited in national technical regulations.

7.4. Incorrectly filled, damaged (unreadable) or filled by an unauthorized person warranty card will not

be considered valid and binding for the Guarantor.

Mode

number Description Signalling diodes

(numbering from bottom to top)

Temperature 60°C, timer 1 hour Flashes red. Frequency 1 sec.