Subaru H001SVA800 Manual de usuario
Sold by: Fuji Heavy Industries Ltd.
Smart Engine Start
INSTALLATION MANUAL
Genuine Part # : H001SVA800
Vehicle Model : WRX/STI
Rev 1.0
Tools Required
Phillips Screwdriver
Flat Blade Screwdriver
10mm, 12mm Socket Wrench
Torque Wrench
Torque Screwdriver
10mm Offset wrench
Pliers
Volt Meter (Or Circuit Tester)
Side Cutters
Scissors
Utility Knife
Masking Tape
Electrical Tape
Trim Removal Tool
Isopropyl Alcohol
Cleaning Towel
: Remove : Tighten Torque
: Install : Loosen
: Disconnect
: Discard
: Connect
: Location of Clip or Screw : Re-use
Meaning of Characters
Kit Contents
NOTE: Laws in some communities require that the
vehicle be within view of anyone using the Smart
Engine Start. In some areas, use of the Smart
Engine Start may violate state, provincial or local
laws. Before using the Smart Engine Start, check
your state, provincial and local laws
Service P/N: H001SVA810
Service P/N: H001SVA820
Service P/N: H001SVA830
SES ECU
Quantity: 1
Double-sided tape
Quantity: 1
Foam tape
Quantity: 1
Hood Switch
Quantity: 1
Switch Holder
Quantity: 1
Hood Switch Bracket
Quantity: 1
Bolt (M6x16)(Black)
Quantity: 1
Main Harness
Quantity: 1
Sub-Harness
Quantity: 1
Tie Wrap
Quantity: 10
Foam tape
Quantity: 4
M6 Nut
Quantity: 1
Bolt (M8x20)
Quantity: 1
Screw
Quantity: 1
Key Tag
Quantity: 1
Engine Room Label
Quantity: 1
Wiper Lever Tag
Quantity: 1
Key Ring Tag
Quantity: 1
Owner's Guide
Quantity: 1
Harness Clamp
Quantity: 1
Foam tape
Quantity: 3
Removal of Vehicle Components
Wiring Outline
6
2
3
8
9
12
11
10
Z
A
W
B
C
F
7
G
4
5
1
1 PS Fender Cover
2 DS Dash Cover
3 Lower Dash Cover No.1
4 Lower Dash Cover No.2
5 DS Knee Airbag
6 Center Cluster Panel
7 Audio Unit
8 PS Dash Cover
9 Ornament Panel
10 Glove Box
11 Under Cover
12 Glove Box Inner Cover
A 24P White
B 1P White
C 1P White
F 8P White
G 2P White
Z SES ECU
WWhite Tape Marker
- 2 -
Vehicle Disassembly
1. Place the Vehicle in Park with the Parking Brake set.
2. Disconnect the Negative Battery Terminal.
• Do not touch the Positive Battery Terminal with the
Negative Terminal.
• Note the Battery Cable Position as it will be reinstalled in
the same position.
• Wait at least 30 seconds after disconnecting the
Negative Battery Terminal before disconnecting the
Airbag Connector.
• After the work with battery disconnected, some vehicle
system should be reconfigured. See service manual.
3. Remove the Passenger's Side Fender Cover.
• Remove 2 Clips.
4. Remove the Driver’s Side Dash Cover.
• Disengage 4 Clips.
• Disengage and remove cover from the bottom first
and work upward.
5. Remove the Lower Dash Cover No.1.
• Remove 1 Screw.
• Disengage 8 Clips.
• Disconnect Vehicle connectors.
6. Remove the Lower Dash Cover No.2.
• Remove 1 Screw.
• Disengage 8 Clips by pulling both the top and
bottom of the panel simultaneously.
- 3 -
10. Remove the Passenger’s Side Dash Cover.
• Disengage 4 Clips.
9. Remove the Audio Unit.
• Remove 6 Screws.
• Disconnect Vehicle connectors.
8. Remove the Center Cluster Panel.
• Disengage 13 Clips.
• Disconnect Vehicle connectors.
7. Remove the Driver’s Side Knee Airbag carefully.
• Remove 2 Nuts.
• Hold Airbag as to prevent tension on the Harness.
• Disengage the Yellow Connector Lock by using a
pick tool to lift upward.
• Use a Panel removal tool to carefully lift upward to
unplug the Airbag Connector.
• Wait at least 30 seconds after disconnecting the
Negative Battery Terminal before disconnecting the
Airbag Connector.
• Disengage and remove cover from the bottom first
and work upward.
• Disengage and remove cover from the bottom first
and work upward.
- 4 -
11. Remove the Ornament Panel.
• Disengage 6 Clips.
12. Open the Glove Box.
13. Dislodge the Glove Box.
15. Remove the Lamp Pocket Cover.
• Disengage 1 Clip.
16. Remove the Pocket Lamp from Lamp Pocket Cover.
• Disconnect Vehicle connectors.
17. Remove the Glove Box Inner Cover.
• Remove 7 Screws.
• Disengage 7 Clips.
• Disengage 2 vehicle harness Clips.
14. Remove the Under Cover.
• Remove 3 Clips.
- 5 -
Installation Procedure
SES ECU Preparation and Installation
1. Clean the area indicated on the topside of the Glove
Box Inner Cover.
2. Attach the Double-Sided tape to the Glove Box
Inner Cover as shown.
• Clean attachment surface using isopropyl alcohol and
cleaning towel.
• To achieve maximum bond strength of Tape, the
attachment surface temperature must be between
68°F-110°F (20°C-43°C) upon application.
• Verify that the Double-sided tape is firmly attached.
3. Attach the Foam Tape to the SES ECU as shown.
0mm
0mm
• Clean attachment surface using isopropyl alcohol and
cleaning towel.
OO
OO
- 6 -
4. Attach the SES ECU to the topside of the Glove Box
Inner Cover as shown.
• Clean attachment surface using isopropyl alcohol and
cleaning towel.
• To achieve maximum bond strength of Tape, the
attachment surface temperature must be between
68°F-110°F (20°C-43°C) upon application.
• Verify that the SES ECU is firmly attached.
1. Route the Main Harness's 24P Connector toward
the Glove Box area.
2. Route the Main Harness's 8P and 2P Connectors
toward the J/B area.
Main Harness Installation
• Use caution when installing the Main Harness. Be
sure to route and attach harness away from sharp
metal surfaces.
OO
OO
- 7 -
3. Route the Main Harness's 24P Connector along the
Vehicle Harness behind the Vehicle Bracket.
4. Route the Main Harness's 24P Connector toward
the Glove Box area.
5. Secure the Main Harness White Marker to the
Vehicle Harness using 1 Tie Wrap.
6. Secure the Main Harness to the Vehicle Harness
using 1 Tie Wrap.
7. Secure the Main Harness to the Vehicle Harness
using 1 Tie Wrap.
- 8 -
8. Secure the Main Harness to the Vehicle Harness
using 1 Tie Wrap.
9. Remove the Tape securing the Vehicle’s 8P and 2P
Pre-Connectors.
10. Disconnect the Wire Jumper connector from the
Vehicle's 2P Pre-Connector.
11. Connect the Main Harness's 8P Connector to the
Vehicle's 8P Pre-Connector.
12. Connect the Main Harness's 2P Connector to the
Vehicle's 2P Pre-Connector.
• Discard the Wire Jumper connector. (This is used for
the power window interrupt circuit.)
• Ensure routing of main harness does not interfere
with climate control mechanism. The main harness
must be secured to the vehicle harness with no slack
in this area.
- 9 -
13. Secure the Main Harness to the Vehicle Harness
using 2 Tie Wraps.
14. Secure the 8P and 2P Connector to the Vehicle
Harness using 1 Tie Wrap.
15. Connect the Main Harness’s 24P White Connector
to the SES ECU.
16. Reinstall the Glove Box Inner Cover.
FM5-RES052
• The Smart Engine Start ID must be registered first, so
do not secure the 1P Connectors yet.
- 10 -
Tabla de contenidos
Idiomas:
Otros manuales de Arranque remoto de Subaru
Subaru
Subaru H011SAJ400 Manual de usuario
Subaru
Subaru H001SFJ800 Manual de usuario
Subaru
Subaru H7110FS101 Manual de usuario
Subaru
Subaru H001SSG400 Manual de usuario
Subaru
Subaru LEGACY H7110LS200 Manual de usuario
Subaru
Subaru H001SFL300 Manual de usuario
Subaru
Subaru H001SFJ600 Manual de usuario
Subaru
Subaru H001SFL400 Manual de usuario
Subaru
Subaru Remote Start Manual de usuario
Subaru
Subaru H001SXA000 Manual de usuario
