Sub-Zero CBIC-18FI Guía
NEW GENERATION
INTERNATIONAL DESIGN GUIDE
2
|
English
Features and specications are subject to change at any
time without notice.
IMPORTANT NOTE: Throughout this guide, dimensions may
vary by ± 3 mm.
Contents
3Integrated Refrigeration
4Specications
8Custom Panels
12 Wine Storage
13 Specications
17 Custom Panels
20 Sub-Zero Warranty
subzero.com
|
3
SUB-ZERO INTEGRATED REFRIGERATION
KEY FEATURES
•Custom front panels and hardware allow for innite
design options.
•Point-of-use refrigeration that can be placed anywhere
in the home.
•Dual refrigeration; two compressors preserve food’s
goodness in self-contained compartments.
•Energy efcient. All models rated A+ or higher.
•Star-K certied.
Integrated Refrigeration
With custom front panels and hardware, Sub-Zero invented
integrated columns, tall and drawer models that disappear
into the decor. Integrated units t ush with other cabinets,
making integrated refrigeration as practical and beautiful in
the master suite, bar or theatre room as in the kitchen.
INTEGRATED MODELS
ICBIC-18FI
ICBIC-24R
ICBIC-24FI
ICBIC-30RID
ICBIC-30FI
ICBIC-36RID
ICBIT-30RID
ICBIT-30CIID
ICBID-30RP
ICBID-30CI
ICBID-36CI
ICBIT-36CIID
4
|
English
Overall Dimensions
COLUMN
SUB-ZERO INTEGRATED REFRIGERATION
1765
mm
A610 mm
2134
mm*
114 mm
92 mm
*2121 mm MIN TO 2146 mm MAX
B
C
45 mm
COLUMN A B C
ICBIC-18FI 457 mm 64 mm 419 mm
ICBIC-24R, ICBIC-24FI 610 mm 102 mm 572 mm
ICBIC-30RID, ICBIC-30FI 762 mm 143 mm 724 mm
ICBIC-36RID 914 mm 184 mm 876 mm
Specications
INTERIOR CAPACITY R (L) F (L)
COLUMN
ICBIC-18FI 238
ICBIC-24R 365
ICBIC-24FI 348
ICBIC-30RID 475
ICBIC-30FI 415
ICBIC-36RID 397
TALL
ICBIT-30RID 397
ICBIT-30CIID 295 95
ICBIT-36CIID 359 130
DRAWER
ICBID-30RP 138
ICBID-30CI 58 39
ICBID-36CI 72 49
SHIPPING WEIGHT kg
COLUMN
ICBIC-18FI 118
ICBIC-24R, ICBIC-24FI 154
ICBIC-30RID, ICBIC-30FI 181
ICBIC-36RID 200
TALL
ICBIT-30RID, ICBIT-30CIID 181
ICBIT-36CIID 209
DRAWER
ICBID-30RP, ICBID-30CI 95
ICBID-36CI 113
IMPORTANT NOTE: Overall dimensions do not include
panels or handles. Dimensions will vary with panel
thickness.
subzero.com
|
5
Overall Dimensions
TALL
SUB-ZERO INTEGRATED REFRIGERATION
DRAWER
451
mm
A610 mm
2134
mm*
268
mm
1140
mm
338
mm
10 mm
114 mm
92 mm
*2121 mm MIN TO 2146 mm MAX
10 mm
B
C
45 mm
A
451
mm
610 mm
6 mm
876
mm* 268
mm
338
mm
10 mm
92 mm
*864 mm MIN TO 889 mm MAX
TALL A B C
ICBIT-30RID, ICBIT-30CIID 762 mm 143 mm 724 mm
ICBIT-36CIID 914 mm 184 mm 876 mm
DRAWER A
ICBID-30RP, ICBID-30CI 762 mm
ICBID-36CI 914 mm
6
|
English
Opening Dimensions
INTEGRATED MODELS
SUB-ZERO INTEGRATED REFRIGERATION
OPENING DIMENSIONS
COLUMN A B
ICBIC-18FI 457 mm 2134 mm
ICBIC-24R, ICBIC-24FI 610 mm 2134 mm
ICBIC-30RID, ICBIC-30FI 762 mm 2134 mm
ICBIC-36RID 914 mm 2134 mm
TALL A B
ICBIT-30RID, ICBIT-30CIID 762 mm 2134 mm
ICBIT-36CIID 914 mm 2134 mm
DRAWER A B
ICBID-30RP, ICBID-30CI 762 mm 876 mm
ICBID-36CI 914 mm 876 mm
The depth of each integrated model is 610 mm. Allow for
panel thickness when planning the nished opening depth.
Approximately 89 mm of the opening depth may be visible
when the door/drawers are open and should be nished to
match cabinetry. Refer to the illustration below.
DUAL INSTALLATION
When installing two units side by side in a dual installa-
tion, the opening width is the width of the two units added
together. A dual installation kit will be required for this instal-
lation. If a dual installation kit is not specied, a minimum
51 mm ller strip is required between units.
Dual installation kits are available through an authorized
Sub-Zero dealer. For questions regarding the installation,
contact your authorized Sub-Zero dealer.
DETAIL
635 mm
OPENING
DEPTH
A
OPENING WIDTH
635 mm
OPENING DEPTH
B
OPENING
HEIGHT
TOP VIEW
FRONT VIEWSIDE VIEW
89 mm
(TYPICAL)
19 mm
(TYPICAL)
SHADED AREA
SHOULD BE
FINISHED
TO MATCH
CABINETRY
subzero.com
|
7
SUB-ZERO INTEGRATED REFRIGERATION
Electrical
The electrical supply must be located within the shaded
area shown in the illustration and chart below. A separate
circuit, servicing only this appliance is required. A ground
fault circuit interrupter (GFCI) is not recommended and may
cause interruption of operation.
Installation must comply with all applicable electrical codes.
ELECTRICAL REQUIREMENTS
Power Supply 220-240 V AC, 50/60 Hz
Circuit Breaker 10 amp
Receptacle grounding-type (earthed)
ELECTRICAL SUPPLY LOCATION
WIDTH A
457 mm Model 152 mm
610 mm Model 241 mm
762 mm Model 318 mm
914 mm Model 394 mm
A
6 mm
108
mm
114 mm
FRONT VIEW
FLOOR
LEFT SIDE
OF OPENING
E
Electrical supply location.
Plumbing
The water supply line should be located within the shaded
area shown in the illustrations below. The water supply line
should be connected to the house supply with an easily
accessible shut-off valve. Do not use self-piercing valves.
The water supply line must not interfere with installation of
the anti-tip bracket.
A reverse osmosis system can be used provided there
is constant water pressure of 2.4–8.3 bar supplied to the
unit at all times. A copper line is not recommended for this
application.
Installation must comply with all applicable plumbing codes.
PLUMBING REQUIREMENTS
Water Supply Line 1/4" OD copper, braided
stainless steel or PEX tubing
Water Pressure 2.4–8.3 bar
Excess Water Line for Connection .9 m
WATER SUPPLY LOCATION
WIDTH A
457 mm Model 76 mm
610 mm Model 140 mm
762 mm Model 152 mm
914 mm Model 229 mm
76 mm
FRONT VIEW
FLOOR
TOP VIEW
BACK WALL
13 mm
152
mm
A
WATER
LINE
A
152
mm
RIGHT SIDE
OF OPENING
RIGHT
SIDE OF
OPENING
76 mm
FRONT VIEW
FLOOR
TOP VIEW
BACK WALL
13 mm
152
mm
A
WATER
LINE
A
152
mm
RIGHT SIDE
OF OPENING
RIGHT
SIDE OF
OPENING
Water supply location (rear).
Water supply location (bottom).
8
|
English
SUB-ZERO INTEGRATED REFRIGERATION
Custom Panels
For integrated models, custom door panels and handle
hardware must be provided. Refer to the panel requirements
chart and typical panel dimensions.
The thickness of the custom panel can vary. A minimum
16 mm thick panel is required, but the thickness can be
increased provided it does not exceed the weight limit. The
depth of each integrated model is 610 mm. Allow for panel
thickness when planning the nished opening depth. Refer
to the full-scale template on page 11.
CAUTION
As reveals between cabinetry and the unit decrease,
severe nger pinching can occur while door is closing.
Finish all sides of custom panels. They will be visible when
the door/drawer is open.
D-style handles are recommended. Door handles must be
located near the edge of the panel opposite the hinge and
should be centered top to bottom. Drawer handles must
be located near the top edge of each panel. Stainless steel
tubular and pro handles are available through an authorized
Sub-Zero dealer.
PANEL REQUIREMENTS
COLUMN MAX WEIGHT
457 mm Model 20 kg
610 mm Model 27 kg
762 mm / 914 mm Model 34 kg
TALL (DOOR) MAX WEIGHT
762 mm Model 22 kg
914 mm Model 27 kg
DRAWER MAX WEIGHT
Drawer Panel 7 kg
PANEL THICKNESS MINIMUM
All Panels 16 mm
TYPICAL PANEL DIMENSIONS
Typical panel dimensions are based on a 2134 mm nished
height for column and tall models and 876 mm for drawer
models, with a 102 mm toe kick and 3 mm reveals. Panel
dimensions must be adjusted accordingly for all other instal-
lations. Refer to the illustration for panel heights and the
chart below for panel widths.
PANEL WIDTH
MODEL W
457 mm Model 451 mm
610 mm Model 603 mm
762 mm Model 756 mm
914 mm Model 908 mm
DUAL INSTALLATION
For dual installations, refer to the illustration for panel
heights and the chart below for panel widths.
PANEL WIDTH
MODEL W
457 mm Model 452 mm
610 mm Model 605 mm
762 mm Model 757 mm
914 mm Model 910 mm
W
1254
mm
345
mm
424
mm
WW
2029
mm
Column
Tall
Drawer
subzero.com
|
9
SUB-ZERO INTEGRATED REFRIGERATION
Custom Panels
DOOR PANEL HEIGHT
The height of the custom door panel can extend beyond the
typical panel height, provided it does not exceed the weight
limit. Refer to the illustration below.
TOE KICK CLEARANCE
The height of the toe kick area can extend beyond the
typical toe kick height, provided it does not exceed the
dimensions in the illustration below.
610 mm
TO BACK OF UNIT
VENTED
LOUVERS
HINGE
DOOR
PANEL
29 mm
MAX
TOE KICK
ADJUSTMENT
A DECORATIVE TOE KICK
CANNOT EXTEND
BEYOND THIS PLANE
102 mm
TO
152 mm
FROM FLOOR
Toe kick—side view.
45
mm
A DECORATIVE VALANCE
CANNOT EXTEND
BEYOND THIS PLANE
DOOR
PANEL
HINGE
610 mm
TO BACK OF UNIT
2134
mm
3 mm
Upper valance (column and tall)—side view.
10
|
English
SUB-ZERO INTEGRATED REFRIGERATION
Handle Hardware
Optional stainless steel tubular and pro handles are avail-
able through an authorized Sub-Zero dealer.
Refer to the chart and illustration below for the length and
stud spacing of standard handles for integrated models.
HANDLE LENGTH A
TUBULAR HANDLE
1273 mm 1197 mm
845 mm 768 mm
692 mm 616 mm
616 mm 540 mm
540 mm 464 mm
PRO HANDLE
1229 mm 1197 mm
800 mm 768 mm
648 mm 616 mm
572 mm 540 mm
495 mm 464 mm
A
Stud spacing.
Este manual sirve para los siguientes modelos
11
Tabla de contenidos
Otros manuales de Refrigerador de Sub-Zero
Sub-Zero
Sub-Zero BI-42SD Manual de usuario
Sub-Zero
Sub-Zero ICBBI Series Manual de servicio
Sub-Zero
Sub-Zero Built-In Refrigeration Manual del propietario
Sub-Zero
Sub-Zero UC-24BG/S/TH-RH Manual de usuario
Sub-Zero
Sub-Zero 736TR Manual de usuario
Sub-Zero
Sub-Zero BI-48SD Instrucciones de montaje
Sub-Zero
Sub-Zero Built-in Series Manual de funcionamiento
Sub-Zero
Sub-Zero ID-30CI Manual de usuario
Sub-Zero
Sub-Zero New Designer Series Guía
Sub-Zero
Sub-Zero 700BC Manual de usuario
Sub-Zero
Sub-Zero UC-24C(I) Manual de usuario
Sub-Zero
Sub-Zero UC-24B Manual de usuario
Sub-Zero
Sub-Zero 736TR Manual de usuario
Sub-Zero
Sub-Zero ICBPRO3650RH Manual de usuario
Sub-Zero
Sub-Zero 200 Series Manual de usuario
Sub-Zero
Sub-Zero INTEGRATED REFRIGERATION Manual de usuario
Sub-Zero
Sub-Zero 736TC Manual de usuario
Sub-Zero
Sub-Zero 632 Instrucciones de uso
Sub-Zero
Sub-Zero 700-2 Series Manual de usuario
Sub-Zero
Sub-Zero IC-24FI Manual de usuario
