Studer Xcom-232i Manual de usuario

Studer Innotec SA 2017 –V 1.3.0

4O9D

Communication module Xcom-232i

User Manual

Studer Innotec SA

Xcom-232i

2V 1.3.0 User manual

COMMUNICATION MODULE XCOM-232I:USER MANUAL

V 1.3.0

ABOUT THE SOFTWARE

This document applies to software versions V1.4.2 or higher of the Xcom-232i. It is possible to check

the currently used software version with the menu "Information on the system" or to update the

product with the latest software version available on "www.studer-innotec.com/en/downloads/".

LEGAL NOTICE

The use of Studer Innotec SA devices is the responsibility of the customer in all cases. Studer Innotec

SA reserves the right to make any modification to the product without prior notice.

PRODUCT RECYCLING

The Xcom-232i conforms to the European directive 2011/65/EU

on hazardous substances and does not contain the following

elements: lead, cadmium, mercury, hexavalent chrome, PBB or

PBDE.

To dispose of this product, please use the service for collection

of electrical waste and observe all applicable obligations according to the place of purchase.

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 3

TABLE OF CONTENTS

1INTRODUCTION.................................................................................................................................... 4

1.1 The communication module Xcom-232i .......................................................................................4

1.2 Conventions........................................................................................................................................4

1.2.1 Symbols .................................................................................................................................. 4

1.3 Warranty and liability ........................................................................................................................4

1.3.1 Disclaimer of warranty ......................................................................................................... 4

1.3.2 Disclaimer of liability ............................................................................................................. 5

1.3.3 Compatibility......................................................................................................................... 5

1.4 Safety precautions.............................................................................................................................5

1.4.1 Generalities ........................................................................................................................... 5

1.4.2 Warnings ................................................................................................................................ 5

2EU DECLARATION OF CONFORMITY .................................................................................................. 6

3INSTALLATION ...................................................................................................................................... 7

3.1 Mounting .............................................................................................................................................8

3.1.1 Connecting the communication bus ................................................................................ 8

4DESCRIPTION OF THE COMMUNICATION MODULE XCOM-232I..................................................... 9

4.1 Front......................................................................................................................................................9

4.2 Back....................................................................................................................................................11

4.3 MicroSD card ....................................................................................................................................11

5RS-232 COMMUNICATION ............................................................................................................... 12

6DATA LOGGER ................................................................................................................................... 13

6.1 Functioning........................................................................................................................................13

6.2 Analysis and visualization of the data with the Xtender data analysis tool or with the

Xtender Matlab® data analysis ...............................................................................................................13

7SOFTWARE UPDATING ....................................................................................................................... 14

7.1 Updating process.............................................................................................................................14

8DIMENSIONS ...................................................................................................................................... 15

9MOUNTING ........................................................................................................................................ 16

Studer Innotec SA

Xcom-232i

4V 1.3.0 User manual

1INTRODUCTION

1.1 THE COMMUNICATION MODULE XCOM-232I

Equipped with a serial port RS-232, the communication module Xcom-232i has been designed for

remote communication with any SCADA (Supervisory Control and Data) system. This module also

allows for data collection (energy consumption of a system, state of the auxiliary relays, input

currents and voltages, etc...) on a MicroSD card thanks to the function "Data logger".

1.2 CONVENTIONS

1.2.1 Symbols

This symbol is used to indicate the presence of a dangerous voltage that is sufficient

to constitute a risk of electric shock.

1.3 WARRANTY AND LIABILITY

During production and assembling, each Xcom-232i gets several controls and tests. They are

carried out in full respect of fixed procedures. Each Xcom-232i is given a serial number allowing a

perfect follow-up of the controls, in conformity with the specific data of every device. For this

reason, it is very important to never remove the descriptive sticker bearing the serial number. The

production, the assembling and the tests of each Xcom-232i are entirely carried out in our factory

in Sion (CH). The warranty of this product depends on the strict following of the instructions in this

manual. The warranty period for the Xcom-232i is 5 years.

1.3.1 Disclaimer of warranty

No warranty will be applied for damages caused by handling, operation or actions that are not

described in this manual. Damages arisen from the following events are not covered by the

warranty:

Overvoltage on the device.

Reverse polarity while connecting the battery.

Liquid in the device or oxidation due to condensation.

Failures due to a fall or to a mechanical shock.

Modifications made without the explicit authorization of Studer Innotec SA .

Nuts or screws partially or insufficiently tight during installation or maintenance.

Damages due to atmospheric overvoltage (lightning).

Damages due to transport or improper packaging.

Disappearing of original marking items.

This symbol is used to indicate a risk of material damage.

This symbol is used to indicate information that is important or which serves to

optimize your system.

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 5

1.3.2 Disclaimer of liability

Installation, commissioning, use and maintenance of this device cannot be supervised by the

company Studer Innotec SA . For this reason, we do not accept any liability for damages, costs or

losses generated either by an installation that is not conforming to the prescriptions, by a defective

operation or by poor maintenance. The use of this device is under the responsibility of the end-

user. This device is neither designed nor guaranteed for the supply of life support applications or

any other critical application with potential risks for human beings of for the environment. We shall

assume no liability for patent infringement or other third party rights involved in the use of this

device.

1.3.3 Compatibility

Studer Innotec SA guarantees the compatibility of the software updates with the hardware for

one year, starting from the date of purchase. The updates are no longer guaranteed beyond this

date and a hardware upgrade may be required. Please contact your reseller for any additional

information on compatibility.

1.4 SAFETY PRECAUTIONS

1.4.1 Generalities

Carefully read all safety instructions before proceeding with the installation and commissioning of

the device. Failure to follow these instructions might constitute a lethal physical danger but can

also damage the functionalities of the device. Therefore this manual should always be kept close

to the device.

For any installation, the local and national norms and regulations in force must be

strictly followed.

1.4.2 Warnings

Wherever the installation, the person in charge of installation and commissioning must

perfectly know the safety measures and the prescriptions in force in the country. Therefore,

the whole maintenance must be carried out by a qualified staff.

All components connected to this device must be conforming to the laws and regulations

in force. Persons without a written authorization from Studer Innotec SA are forbidden to

do any changes, modifications or repairs whatsoever. Regarding authorized modifications

and replacements, only genuine components shall be used.

This device is meant for indoor use only and must under no circumstances be exposed to

rain, snow or any other humid or dusty environment.

If used in motor vehicles, this device must also be protected against vibrations by

absorbing components.

Studer Innotec SA

Xcom-232i

6V 1.3.0 User manual

2EU DECLARATION OF CONFORMITY

The communication module Xcom-232i described in this manual meets the requirements specified

in the following EU directives and norms:

Low Voltage Directive (LVD) 2014/35/EU

- EN 62368-1:2014

Electromagnetic Compliance (EMC) Directive 2014/30/EU

- EN 61000-6-2:2005

- EN 61000-6-4:2007/A1:2011

CH - 1950 Sion, November 2016

Studer Innotec SA (R. Studer)

Studer Innotec SA contact details

Studer Innotec SA

Rue des Casernes 57

CH - 1950 Sion

Schweiz

+41(0) 27 205 60 80

+41(0) 27 205 60 88

info@studer-innotec.com

www.studer-innotec.com

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 7

3INSTALLATION

The Xcom-232i is to be mounted as close as possible to the supervision or SCADA control system

(PC, programmable logic controller, microcontroller) due to the more restrictive limits of the RS-

232 connection as compared with the Xtender communication bus.

Figure 3.1: Connection schematics of the Xcom-232i (Example 1)

Figure 3.2: Connection schematics of the Xcom-232i (Example 2)

Studer Innotec SA

Xcom-232i

8V 1.3.0 User manual

3.1 MOUNTING

The Xcom-232i can be mounted directly on any support by means of the supplied fixing plate, on

a smooth surface with double-side adhesive (see Figure 9 (p. 16)) or on a DIN rail using the supplied

DIN clips.

3.1.1 Connecting the communication bus

The devices of the Xtender range are equipped with an own communication bus for data

exchange, configuration and updating of the system. Connection is being made by linking the

devices with the communication cables. One gets then a bus online where a link end must be

activated on the devices on each end, to obtain the configuration of the Figure 3.3 .

Each device is equipped with a switch offering to choose between open "O" and terminated "T".

The devices at the end of the line must be set on "T". The others, receiving two communication

cables, must be set on "O".

By default, the termination is not activated on each product of Studer Innotec SA .

Figure 3.3: Online communication bus of an Xtender system

A wrong setting of the link ends can lead to an erratic running of the installation or

impede its updating.

Studer Innotec SA

Xcom-232i

User manual V 1.3.0 9

4DESCRIPTION OF THE COMMUNICATION MODULE

XCOM-232I

The communication module Xcom-232i consists of different parts with various functions. Here

below, you will find the description of each part and of its function(s).

4.1 FRONT

Front and isometric view of the Xcom-232i

Key

Description of the part

Description of the function

Push button

This button activates or deactivates the data logging

functioni by pressing it for more than 3 seconds. When

the data logging function is activated, the signalisation

LED (b) is continuously green.

Bicoloured signalisation

LED

The signalisation LED indicates different functions by

combining colour and blinking frequency. Below are

the descriptions of each function.

Updating process:

During the Xcom-232i updating process (after insertion

of a MicroSD card containing the updates), the

signalisation LED blinks in red with a cyclical ratio of 50

% (Ton = 50 % | Toff = 50 %).

The updating process can take between 3

and 15 minutes. During this period, it is

possible that the signalisation LED does not

meet exactly the cyclical ratio described

above (Ton=50% |Toff=50%). The update

process is completed as soon as the

signalisation LED stops blinking red for at

least 20 seconds.

Error during update or back up of the data logger :

If the Xcom-232i detects an error, the signalisation LED

is continuously red (Ton = 100 % | Toff = 0 %).

Studer Innotec SA

Xcom-232i

10 V 1.3.0 User manual

MicroSD card full:

If the Xcom-232i detects that the MicroSD card is full,

the signalisation LED blinks in red with a cyclical ratio of

10 % (Ton = 10 % | Toff = 90 %).

Data logging:

When the data logging function is activated, the

signalisation LED is green (Ton = 100% | Toff = 0 %).

Communication (via RS-232 connection):

When the communication via the RS-232 connection is

active, the signalisation LED blinks in green with a

cyclical ratio of 20 % (Ton = 20 % | Toff = 80 %).

Insertion of the SD card:

When inserting an SD card the signalisation LED is both

red and green simultaneously for 1.5 seconds.

In operation:

The signalisation LED blinks in green twice when the

Xcom-232i is operation and none of the above

mentioned states is indicated.

If several of the three states indicated by red

LED light occur simultaneously, they will be

displayed in the following priority order:

Update processing

Error during updating

MicroSD card full

If the two states indicated by green LED light

occur simultaneously, the signal indicating

communication via RS-232 connection is

reversed (Ton=80% |Toff=20%).

Connectors CAN

These connectors are used to connect the Xcom-232i

with one or several Xtenders.

Switch for CAN

termination

This switch activates or deactivates the

communication bus termination ii. The termination is by

default activated on each product from Studer

Innotec SA .

iSee Chapter 6: "Data logger" (p. 13)

iiSee Section 3.1.1 "Connecting the communication bus" (p.8)

Tabla de contenidos

Otros manuales de Sistema de conferencias de Studer

Studer

Studer Xcom-GSM Manual de usuario

Studer

Studer Xcom-LAN Manual de usuario

Studer

Studer Xcom-GSM Manual de usuario

Studer

Studer Xcom-GSM Manual de usuario

Manuales populares de Sistema de conferencias de otras marcas

Kramer

Kramer VIA GO Manual de usuario

AVT

AVT MAGIC AC1 Go Manual de usuario

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manual de usuario

Sony

Sony PCS-I150 Manual de usuario

Middle Atlantic Products

Middle Atlantic Products VTC Series Manual de usuario

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guía

Speakerbus

Speakerbus iD 712 Manual de usuario

Trelleborg

Trelleborg SafePilot CAT PRO Manual de usuario

Sennheiser

Sennheiser ADN Manual de usuario

ADTRAN

ADTRAN NetVanta 7100 Manual de usuario

AINA

AINA PTT Voice Responder Manual de usuario

Yamaha

Yamaha ProjectPhone PJP-100H Manual de usuario

vissonic

vissonic VLI Series Manual de usuario

Panasonic

Panasonic KX-VC500 Manual de usuario

Poly

Poly Trio 8300 Manual de usuario

Crestron

Crestron Mercury CCS-UCA-SMK Dibujo dimensional

Inmarsat

Inmarsat mini M Manual de usuario

Tenveo

Tenveo ALL-IN-ONE Manual de usuario