Stuart Turner CH 3-30 CI Guía

Read this manual carefully before commencing installation.

This manual covers the following products suitable for 220/1/60 supply:

CH 3–30 CI

Pt. No. 46672

60 Hz

CH 3–40 CI

Pt. No. 46717

CH 3–45 CI

Pt. No. 46718

STUART

Installation, Operation & Maintenance

Instructions

Please leave this instruction booklet with the owner as it contains

important warranty, maintenance and safety information

- 2 -

Arabic Installation Operation & Maintenance Instructions ................... 25

English (GB) Installation Operation & Maintenance Instructions .............. 2

PRODUCT DESCRIPTION

Electric motor driven centrifugal pump.

APPLICATION

These self priming centrifugal pumps are designed to pump clean fresh water and can

be used for pressure boosting, fluid transfer and distribution.

Inlet pressures to the pump and ambient temperatures must not exceed the values

given in the technical specifications.

STORAGE

If this product is not to be installed immediately on receipt, ensure that it is stored in a

dry, frost and vibration free location in its original packaging.

CONTENTS Page

Checklist ...........................................................5

Important Facts – read before commencing installation ......................6

Location ............................................................7

Electrical Installation ..................................................8

Plumbing ...........................................................10

Technical Specification ................................................11

Trouble Shooting .....................................................12

Warranty ...........................................................13

- 3 -

Cont ...

WARNINGS:

zThis pump set must not be used for any other

application without the written consent of Stuart

Turner Limited.

zDo not connect this pump to the mains water supply.

zThis appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved.

zChildren shall not play with the appliance.

zCleaning and user maintenance shall not be made

by children without supervision.

zMaximum head (closed valve) 34 metres (CH 3–30 CI),

42 metres (CH 3–40 CI), 46 metres (CH 3–45 CI).

zThe motor casing can become very hot under

normal operating conditions. Care must be taken

to ensure it cannot be touched during operation.

zThe electrical installation must be carried out in

accordance with the current national electrical

regulations.

zCheck the mains voltage and frequency

corresponds to the values on the pump rating plate.

zThe electrical installation must be installed by a

qualified person.

zIn the interests of electrical safety a 30 mA residual

current device (R.C.D. not supplied) should be

installed in the supply circuit. This may be part of

a consumer unit or a separate unit.

zBefore starting work on the electrical supply ensure

power supply is isolated.

- 4 -

Cont ...

zDO NOT allow the supply cord to contact hot

surfaces, including the motor shell, pump body or

pipework. The cord should be safely routed and

secured by cable clips.

zThis appliance must be earthed via the supply cord,

which must be correctly connected to the earth

point located in the terminal box.

zThe supply cord and internal wiring within the

terminal box are routed and secured to ensure

compliance with the electrical standard

IEC 60335–1. It is essential that prior to any

disturbance of this internal wiring, all cable routing

and securing details are carefully noted to ensure

re-assembly to the same factory pattern is always

maintained.

Please read installation details carefully as they are intended to ensure this product

provides long, trouble free service. Failure to install the unit in accordance with the

installation instructions will lead to invalidation of the warranty.

- 5 -

CHECKLIST

Your product may vary slightly from the picture above.

Fig. 1

IMPORTANT: With the pump

removed from its packaging

check for any damage prior to

installation. If any damage is

found contact Stuart Turner Ltd

within 24 hours of receipt.

Inlet

Outlet

A short length of cable is also supplied

for shop test purposes only.

- 6 -

Cont ...

1 IMPORTANT FACTS: READ BEFORE COMMENCING PUMP INSTALLATION

A Water storage capacity.

1.11 The water storage capacity must be sufficient to meet the flow rates required

by the pumped equipment and any other water using fittings and appliances,

which may be operated simultaneously. DO NOT RUN PUMP DRY.

1.12 Ensure the pump is primed as described in the priming section before

starting, damage to the shaft seal will result otherwise. See Section 4 –

Plumbing.

B Water temperature

The water entering the pump must be controlled as follows:

1.13 The maximum allowable water temperature is 65 oC.

1.14 The minimum allowable water temperature is 4 oC.

1.15 Ambient temperature: The pump must be sited in a location where the

maximum ambient temperature does not exceed 50 oC.

1.16 DO NOT fit a pump if the hot water is heated via a method whereby the water

temperature cannot be controlled, such as solar or solid fuel you must

consult the TechAssist team on +44 (0) 800 31 969 80.

C Pipework – general

1.17 Pipework design: Care should be taken in the design of pipework runs to

minimize the risk of air locks e.g. use drawn bends rather than 90obends.

1.18 DO NOT allow contact with oil or cellulose based paints, paint thinners

or strippers, acid based descalents or aggressive cleaning agents.

D Plumbing installation regulations

1.19 The plumbing installation must be installed by a qualified person and in

accordance with local regulations.

- 7 -

Cont ...

2 LOCATION  GENERAL

2.11 Access: For emergencies and maintenance the pump must be

easily accessible.

2.12 Protection: The pump must be located in a dry position, frost free

and protected from freezing.

2.13 Ventilation: Ensure an adequate air flow to cool the pump.

Separate the pump from other appliances that generate heat.

An 80 mm (3 “) air gap must be maintained around the pump.

2.14 Safety: The motor casing can become very hot under normal

operating conditions. Care must be taken to ensure it cannot

be touched during operation.

2.15 Water retention: Site the pump in a location where in the unlikely

event of a water leak, any spillage is contained or routed to avoid

electrics or areas sensitive to water damage.

2.16 Pump position: The pump must be positioned on its mounting feet and as

close to the water source as possible.

2.17 Mounting foot securing: This pump is fitted with cast iron feet. If there is a

requirement to secure the pump via the feet, the following points should be

noted.

The pump should be mounted only in the horizontal position.

The mounting bolts used to secure the pump must be fitted with a plain

washer to distribute clamping load evenly across load bearing face of foot

(not supplied).

Fig. 2

PLAIN

WASHER

MOUNTING

FOOT

BOLT

Fig. 3

- 8 -

Cont ...

3 ELECTRICAL INSTALLATION  EARTHING

3.11 Regulations: The electrical installation must be carried out in

accordance with the current local regulations by a qualified person.

3.12 Safety: In the interests of electrical safety a 30 mA residual current

device (R.C.D. not supplied) should be installed in the supply circuit.

This may be part of a consumer unit or a separate unit.

3.13 Before starting work on the electrical supply ensure power supply is

isolated.

3.14 DO NOT allow the supply cord to contact hot surfaces, including the

motor shell, pump body or pipework. The cord should be safely

routed and secured by cable clips.

3.15 Earthing: This appliance must be earthed via the supply cord, which must be

correctly connected to the earth point located in the terminal box.

3.16 Connections: The pump must be permanently connected to the fixed wiring

of the mains supply, via a dedicated double pole switched fused spur off the

ring main.

3.17 Wiring of connection unit:

WARNING: This appliance must be earthed.

This product is supplied with a short length of cable for test purposes

only. It must be removed and a 3 × 1.5 mm2cable must be fitted in order to

comply with IEC 60335–1 standard.

3.18 Wiring diagram:

220 VAC/1PH/60Hz SUPPLY

L N E

BROWN

BLUE

GREEN/YELLOW

RED

BLACK

CAPACITOR

MOTOR

RED

YELLOW

Fig. 4

- 9 -

3.19 Fuse: All models should use 13 Amp fuse.

3.20 Supply cord replacement:

The internal wiring within the terminal box must be routed and

secured to ensure compliance with the electrical standard

IEC 60335–1. It is essential that prior to any disturbance of this

internal wiring, all cable routing and securing details are carefully

noted to ensure re-assembly to the same factory pattern is always

maintained.

3.21 Cable Gland Fitting Instructions:

To enable correct assembly of the cable gland the

‘O’-ring (Fig. 5 item 1) must be placed over the cable

before the clamping insert (Fig. 5 item 2) can be

tightened.

Note: Cable diameter range:- 9.2 mm to 11.9 mm.

Fig. 5

- 10 -

4 PLUMBING

4.11 Pipework: For optimum performance pipework use 22 mm dia., 15 mm can be

used but will result in reduced pump performance.

4.12 Isolating valves: Separate isolating valves (non restrictive) must be fitted to

allow easy pump service.

4.13 Although this pump is not self priming, once fitted with a footvalve and

strainer it can be used to draw water from a storage tank below the pump

position, or without a footvalve and stainer, from a tank above the pump

position.

4.14 System flushing: The pipework system should be flushed out

prior to the pump being connected to ensure any contaminants/

chemical residues and foreign bodies are removed from elsewhere

in the system.

4.15 Priming:

Never operate pump with inlet and/or outlet isolating valves in the

closed position. Damage will occur!

The pump must be primed (filled with water) before starting.

4.16 Flooded suction conditions:

Turn on the isolating valves.

(a) Loosen vent plug and allow an even flow of water this may take a

few seconds.

(b) Re-seal vent plug, nipping tight.

The pump is now ready to start.

4.17 Suction lift conditions:

Turn on isolating valves

(a) Loosen vent plug.

(b) Fill the pump head and suction

pipe with water from the discharge

port until filled with water.

4.18 Maintenance:

This product is maintenance free.

Max. flooded

suction head

28 m

Fig. 6

Max. suction

lift 4.6 m

Min. immersion

depth 0.5 m

Suction pipe run, no

greater than 6 m

Min. flooded

suction 0.5 m

Fig. 7

Drain

Plug

Outlet

Inlet

Outlet

Vent Plug

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Bomba de agua de Stuart Turner

Stuart Turner

Stuart Turner CH 4-30 FL Guía

Stuart Turner

Stuart Turner 46647 Guía

Stuart Turner

Stuart Turner ST NH PUMP 18TN Guía

Stuart Turner

Stuart Turner Stuart Guía

Stuart Turner

Stuart Turner SHOWERMATE 46534 Guía

Stuart Turner

Stuart Turner Showermate U2.6 bar Single Guía

Stuart Turner

Stuart Turner Showermate S2.6 bar Single Guía

Stuart Turner

Stuart Turner monsoon extra Manual de usuario

Stuart Turner

Stuart Turner PH 45 TS FL Guía

Stuart Turner

Stuart Turner PH 45 ES Guía

Stuart Turner

Stuart Turner PH 35 ES Guía

Stuart Turner

Stuart Turner mainsboost MBF 60-1-15 Instrucciones de instalación y funcionamiento

Stuart Turner

Stuart Turner Monsoon Extra U1.4 bar Guía

Stuart Turner

Stuart Turner S2.0 bar Twin Guía

Stuart Turner

Stuart Turner MAINSBOOST VariQ Guía

Stuart Turner

Stuart Turner 46601 Guía

Stuart Turner

Stuart Turner PH 45 TS S Guía

Stuart Turner

Stuart Turner Supersub 460A Manual de usuario

Stuart Turner

Stuart Turner CH4-30 Guía

Stuart Turner

Stuart Turner iBOLT 0304 3H-CMT/24 Guía

Stuart Turner

Stuart Turner Mainboost MJ3 VM Guía

Stuart Turner

Stuart Turner Monsoon Extra 2.6 bar PS Guía

Stuart Turner

Stuart Turner Monsoon Series Guía

Stuart Turner

Stuart Turner Flomate Mains Boost 46574 Instrucciones de instalación y funcionamiento

Manuales populares de Bomba de agua de otras marcas

Neptun

Neptun NPHW 5500 Manual de usuario

Sensidyne

Sensidyne Gilian BDX-II Instrucciones de instalación y funcionamiento

Draper

Draper 47808 Manual de usuario

Trolla

Trolla 12820 Manual de usuario

Sunfab

Sunfab SVH Series Manual de usuario

WilTec

WilTec 50740 Manual de usuario

Fieldmann

Fieldmann FVC 5015 EK Manual de usuario

Everbilt

Everbilt EFSUB5-122HD Manual de usuario

Graco

Graco Husky 3300e Manual de usuario

esotec

esotec 101018 Manual de usuario

moyno

moyno 2000 CC Manual de usuario

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manual de usuario

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guía de solución de problemas

DUROMAX

DUROMAX XP WX Series Manual de usuario

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manual de usuario

Franklin Electric

Franklin Electric IPS Manual de usuario

Xylem

Xylem e-1532 Series Manual de usuario

Milton Roy

Milton Roy PRIMEROYAL Manual de usuario