Strong SR-WM-10U Manual de usuario

ASSEMBLY MANUAL

SR-WM-10U SR-WM-12U SR-WM-16U

WALL MOUNT RACK

SR-WM-10,12, & 16U Installation and Users Manual

pg.3

STRONG WALL MOUNT RACKS

Strong equipment wall racks are available in sizes 10U, 12U, and16U, and are constructed with 11 gauge (3mm) thick

rack rails and 14 gauge (2mm) thick top and bottom covers to provide extreme rigidity. Features include locking fronts,

E-coated rack rails to maintain clean threads, and optional side panels and doors.

PARTS INCLUDED

A. Top Cover (1)

B. Bottom Cover (1)

C. Front Frame Assembly (1)

D. Rear Frame Assembly (1)

E. Side Panels (2)

F. Corner Brackets(4)

G. Plastic Covers for Wire cutouts (not shown)

H. Cover for Fan cutout (not shown)

I. Hardware For Assembly (not shown)

J. Wall Mount Template (not shown)

NOTE: The bolts to secure the rack to the wall are not included. It is strongly recom-

mended that a 3/8” lag bolt be used to mount the rack to the wall studs. If the location

of the rack does not line up with the studs, a 2x4 across the studs or a sheet of plywood

attached to the studs must be used to attach the rack to the wall. THE USE OF MOLLYS

OR ANCHORS IS NOT RECOMMENDED!

pg.4

SR-WM-10,12, & 16U Installation and Users Manual

ASSEMBLY STEPS

1. Prepare the Side Panels

A. Insert rubber bumpers into the left side

panel front edge.

B. Insert rubber bumpers into the right side

panel front edge and side.

Left Side Panel Right Side Panel

2. Mount the Side Panels

A. Place the bottom cover on a at, even surface.

B. Place the rail assemblies on the bottom cover as shown in the diagram.

C. Secure the left side panel to the bottom cover and rail. Do not tighten screws all the way to allow for placement

of the top cover. Repeat for right side panel.

SR-WM-10,12, & 16U Installation and Users Manual

pg.5

4. Attach the Wall Brackets

CAUTION: Due to the weight and size of the Strong Wall Rack, it is recommend-

ed that wall mounting be performed by 2 or more installers in order to avoid

injury or damage to the rack.

A. Attach corner brackets securely to cabinet.

B. Tighten all screws for the top and bottom covers.

3. Install the Top Cover

A. Attach top plate to the cover using included screws.

B. Secure top cover to rack.

C. Tighten all screws for the top and bottom covers.

*NOTE: The top cover secures to the rack with the same screw type as the bottom cover.

See Install the Side Panels for assembly steps.

FRONT VIEW

REAR VIEW

pg.6

SR-WM-10,12, & 16U Installation and Users Manual

5. Attaching to Wall

NOTE: The bolts to secure the rack to the wall are not included. It is strongly recommended

that a 3/8” lag bolt be used to mount the rack to the wall studs. If the location of the rack

does not line up with the studs, a 2x4 across the studs or a sheet of plywood attached to

the studs must be used to attach the rack to the wall.

THE USE OF MOLLYS OR ANCHORS IS NOT RECOMMENDED!

A. Locate wall studs using a stud nder (not included).

B. Position the provided mounting template on the wall in the desired location of the rack.

C. Level the template and mark the wall with the bolt locations.

D. Install the mounting bolts into the locations marked with the template. Leave the bolts loose enough for the brackets

to slide over the heads when hanging the rack. If the optional Swing Kit is being used, proceed to Step F.

E. Slide the wall rack assembly onto the lag bolts in the wall, then nish tightening the bolts in the wall.

CAUTION: This rack is intended for use only with Strong shelf models with a maximum

combined load of 250 pounds. Use with heavier than the maximum load indicated may

result in instability causing possible injury.

SR-WM-10,12, & 16U Installation and Users Manual

pg.7

KNOCK-OUTS

To accommodate for wire pass through, the top and bottom covers have knockouts on the back side of the racks. To utilize

the knockouts, use a hammer and remove the material.

ACCESSORY INSTALLATION

• Determine the layout of your components, their space requirements and where you will place vents or blanks.

• Unbox your rst shelf, starting with the one you will place at the bottom of the rack. The heaviest components should be

placed as low as possible.

• Unfold shelf side panels and mount in desired rack location using four Strong™ rack screws. Accessory mounting screws

are not included with shelves, vents or blanks.

• Install component onto shelf.

• Unbox and install the next shelf, vent or blank following the above steps.

NOTE: It is recommended to use a vent above components that generate excessive heat, such as surround receivers,

ampliers, satellite receivers, DVR’s, cable boxes and media servers.

RACK SCREWS

Screws are not included with Strong™ rack accessories, but extra screws are available (SR-SCREWS-200JAR) for

purchase. One no-roll jar includes 200 black 10/32 screws featuring #2 Phillips heads and Nylon washers.

LIFETIME LIMITED WARRANTY

All Strong™ products have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all components found to

be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been

abused, modied or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service

center with prior notication and an assigned return authorization number (RA).

For Technical Support : 1.866.838.5052

CONTACTING TECHNICAL SUPPORT

Phone: (866) 838-5052

Email: Techsupport@snapav.com

Lifetime

191204-1300

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Rack y soporte de Strong

Strong

Strong Strong Razor Series Manual de usuario

Strong

Strong SM-CB-F-L Manual de usuario

Strong

Strong Contractor Series Manual de usuario

Strong

Strong Strong VersaMount SM-VM-ART2-IW-XL Manual de usuario

Strong

Strong Strong Razor Series Manual de usuario

Strong

Strong SM-PAD-LIFE Manual de usuario

Strong

Strong SR-WM-SK-19 Manual de usuario

Strong

Strong SM-CEILING-T-L Manual de usuario

Strong

Strong Carbon Series Manual de usuario

Strong

Strong SM-FLAT-S Manual de usuario

Strong

Strong FS Series Manual operacional

Strong

Strong SR-CUSTOM Series Manual de usuario

Strong

Strong SM-CBP Series Manual de usuario

Strong

Strong SR-WM-PPH Series Manual de usuario

Strong

Strong VersaBox SM-RBX-PRO-14-BLK Manual de usuario

Strong

Strong SR-CAB-8U Manual de usuario

Strong

Strong SR-WMS Series Manual de usuario

Strong

Strong Strong Razor Series Manual de usuario

Strong

Strong VersaBox SM-RBX-PRO-20-BLK Manual de usuario

Strong

Strong SR-CUSTOM Series Manual de usuario

Strong

Strong Strong Razor Series Manual de usuario

Manuales populares de Rack y soporte de otras marcas

Salamander

Salamander Acadia AC/W/L400/WH Manual de usuario

Fohhn

Fohhn VAT-09 Guía del usuario

ricoo

ricoo FS0522 Manual de usuario

AMSOIL

AMSOIL BMK-22 Guía rápida

Kargo Master

Kargo Master 48220 Manual de usuario

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manual de usuario

ricoo

ricoo S1222 Manual de usuario

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manual de usuario

VidaBox

VidaBox VB MNT FFS2 Manual de usuario

Welch Allyn

Welch Allyn 48960 Manual de usuario

Arkon

Arkon CM035-ST-2 Manual de usuario

PROEL

PROEL PLWIN60C Manual de usuario

Agilent Technologies

Agilent Technologies E2609B Manual de usuario

Mustang

Mustang MV-ARM4 Manual de usuario

Mounting Solutions

Mounting Solutions WRM-320 Manual de usuario

Pyle

Pyle PMKSPAD1 Manual de usuario

ShelterIt

ShelterIt 21208 Manual de usuario

SPL

SPL RackPack?4 1040 Manual de usuario