Streetwize SWPSI2000 Hoja de especificaciones
1
Information for use
SWPSI2000/SWPSI3000
PRODUCT INFO streetwize.online/SWPSI2000
Produktinformation
Information du produit
Información sobre el producto
2000W/3000W
Pure Sine Wave
Inverter
2
2000W Pure Sine Wave Inverter
SWPSI2000
3000W Pure Sine Wave Inverter
SWPSI3000
2000W Continuous Power 3000W Continuous Power
4000W Peak Output 6000W Peak Output
Safely converts your 12V DC Battery to a 230V AC power supply
IMPORTANT: This inverter is only suitable for use with 12V batteries only.
This appliance is primarily designed for operating Class 2 appliances.
Table 1
3
Intention For Use
Thank you for purchasing this Pure Sine Wave inverter from Streetwize. This
inverter safely converts your vehicle’s 12V DC battery into a 240V AC power
supply for using standard UK electrical appliances that totals up to its continuous
output as stated in Table 1.
It is intended for people who require access to an AC power supply in areas
where there is restricted access to a power suppy. It is perfect for caravan/
campervan users as well as tradespeople.
Pure Sine Wave inverters are able to operate more appliances than conventional
modified sine inverters, which cannot operate appliances with an AC motor such
as laser printers and fluorescent lights.
In addition, this pure sine wave inverter is primarily designed for operating a wide
range of Class 2 appliances. Class 2 appliances are double insulated and do not
require earth connections. Most computers, laptops, photocopiers, laser printers,
cordless power tools, and plastic-cased appliances are identified as Class 2
appliances.
Class 1 appliances, on the other hand, are protected by basic insulation and
earthing provision and most typically come in a metal casing. This product is
not suitable for operating Class 1 appliances. Typical Class 1 appliances include
toasters, kettles, washing machines and irons.
IMPORTANT: This inverter is primarily designed for powering appliances upto
its stated continuous output as stated in Table 1. The stated peak output is
only available for a limited time.
4
Health & Safety Guidelines
Product Elements
WARNING! Electric Hazard. Keep away from children
This inverter is not a toy, and it should never be used by children.
This inverter generates the same voltage as a UK 3-pin plug socket. Please
operate it as if you are using any other AC mains socket.
Never insert any kind of foreign object into the inverter’s plug sockets, fan or vent
openings.
Do operate or expose the inverter to water, rain, snow or spray
Never connect the inverter to an AC power source. This inverter is only designed
to accept a DC power supply.
WARNING! Heated Surface
The inverter’s outer casing may become hot after prolonged use or overloading.
During operation, ensure there is atleast a 5cm (2 inches) gap between the
inverter and any other walls.
Please keep any flammable materials away from the inverter during operation.
WARNING! Explosion Hazard
Never use the inverter in the presence of flammable substances
CAUTION!
Do not connect a live AC power source to the inverter’s AC output sockets. This
will damage the inverter, even if the inverter is switched off.
Do not expose the inverter to temperatures over 40oC.
CAUTION! Do not use the inverter with the following equipment:
Class 1 appliances. See Class 1/Class 2 section.
1. Streetwize Pure Sine Wave Inverter
2. Battery connection cables
5
Class 1 / Class 2
Pure Sine Wave & Modified Sine Wave Inverters
As mentioned in the Intention For Use section, this product is primarily designed
for operating Class 2 appliances, which don’t require earthing provisions.
There are two types of inverters: Pure Sine Wave & Modified Sine Wave.
Pure sine wave inverters, when compared with modified sine wave inverters,
deliver a more reliable performance as the 240V AC output is almost identical
to a mains power socket, therefore making it the more preferred option for
operating appliances.
The figure below shows a graphical comparison of modified sine wave inverters
and pure sine wave inverters. Notice how the pure sine wave is smooth while
modified is staggered.
Modified Sine Wave
Pure Sine Wave
Class 1 Class 2
Symbol
Earth Wiring Present Yes No
Insulation Basic Insulation Double Insulation
Appliance casing Metal Plastic
Appliance examples
Toasters, kettles,
washing machines
and irons
Hedge trimmers,
lawn mowers and
drill
6
Operating Instruction
Optimum Working Conditions
For safe & optimum performance, please install the inverter in a location that is:
• Dry - The inverter should not be near any liquid or moisture.
• Cool - Keep it away from any high heat source.
• Well-ventilated - Allow for atleast 5cm of space on all sides.
• Clean - To prevent any dust or unwanted elements from getting inside the inverter.
• Away from flammable substances - To prevent fire or explosion.
Battery Connection Instructions
Please follow the instructions to safely connect the pure sine wave inverter to
your 12V battery.
1. Remove all the elements from its packaging and dispose of the packaging in
the correct manner.
2. Make sure the power switch on the inverter unit is set to OFF.
3. On the reverse side of the inverter, you will find two terminals. One of the
terminals will have a red casing (positive) and the other will have a black
casing (negative) (see Figure 1). Remove the outer casing on both terminals
(see Figure 2).
4. From both terminals, remove the bolts. Then connect the corresponding
battery cables to the terminals via the cables’ respective O-rings, and then
secure the bolt back onto the terminal (see Figure 3).
5. Once the battery cables have been connected, proceed with connecting the
other end of both cables to your vehicle’s (or leisure battery’s) 12V battery
terminals. With the red cable going to the positive terminal and black cable
to the negative terminal. You need a pair of battery clamps to secure it onto
the cable (not included).
Fig 1 Fig 2 Fig 3
7
How To Replace The Fuses
Using The Inverter
Once a safe and secure connection to the battery terminals have been made,
you can proceed to use the inverter.
IMPORTANT: Before powering any appliances via the inverter, make sure the
inverter is switched OFF via the unit’s power switch.
With the battery connection securely made. Plug in your UK appliance(s) via the
two provided sockets or USB device via the USB port. Then, set the inverter unit’s
switch to ON. To turn off, set the unit’s to OFF.
If the inverter does not operate properly, then it is likely that the fuse may need
to be replaced. To replace the fuse, please follow the instructions below:
1. Before attempting to replace the fuse, first ensure that the inverter is
fully disconnected from any DC power supply. And make sure that no UK
appliance is plugged into the inverter.
2. At the front of the inverter, where the two UK sockets are located, unscrew
the four screws with a Phillips screwdriver (not included) on each corner as
highlighted in Figure 4.
Fig 4
3. On the reverse side, using the same Phillips screwdriver, unscrew the screws
located at the top two corners as shown in Figure 5.
Fig 5
8
Fig 6 Fig 7
4. Once the screws are removed, slide off the top panel and place it on the
side. You will see the inverter’s motherboard (see Figure 6).
5. There are eight 30A fuses altogether. The fuses are paired together and they
are located inbetween the yellow marked components as shown in Figure 7.
Please note, some of the fuses will be underneath red & black wiring. Please
take care when lifting these cables.
6. To replace the fuses, please use a suitable pair of tweezers (not included) to
pull the old fuse out. Then replace these fuses with new 30A fuses.
7. Once all the fuses have been replaced, slide the lid back on top and replace
the screws on both the front and back panel.
9
Troubleshooting
Table 3 outlines possible troubleshoots along with its suggested solutions.
Troubleshoot/Problem Possible Cause Suggested Solution
Inverter is not working
Poor battery connection
Turn off the inverter and dis-
connect it from the battery.
Then reconnect the inverter
to the battery and check
to see if the connection is
correct
Short Circuit
Turn off the inverter and
disconnect it from your 12V
battery. Reconnect the invert-
er to the battery’s terminals
and check to see if terminal
connections are correct.
DC input is below 10V
Turn off the inverter and
disconnect it from your 12V
battery. Please check the
Voltage of your battery. This
inverter is only suitable for 12V
batteries only.
DC input is above 15V
Turn off the inverter and
disconnect it from your 12V
battery. Please check the
Voltage of your battery. This
inverter is only suitable for 12V
batteries only.
Blown Fuse Check and replace the fuse.
See How to Replace The Fuses
Inverter gets really hot Overheat
Turn off the inverter and
disconnect it from your 12V
battery and allow the inverter
to fully cool down. Ensure your
inverter is operating in a cool
area.
Inverter shuts down after
operating for a short time Overload
The total Wattage is exceed-
ing the inverter’s specified
continuous power output. Turn
off the inverter and disconnect
it from your 12V battery. Then
disconnect any appliances that
are not required to reduce the
Wattage load.
10
After Use
After you have finished using the inverter (or when the inverter is not in use), turn
off the unit and make sure your vehicle’s fully switched off.
Then disconnect the inverter from the 12V power supply. When disconnecting from
the battery, disconnect the negative cable first, followed by the positive cable.
Best Practices for Protecting Your 12V Battery
• To prevent your vehicle’s 12V battery from being depleted. We recommend running the engine for
10 to 20 minute to recharge the battery after using the inverter for 2 to 3 hours. Important: Before
starting your vehicle’s engine, please disconnect the inverter from your battery/power supply.
• When connecting the inverter to your battery’s terminals, it is important that you connect it via the
correct polarity (i.e. Connect + from inverter to + of battery terminal and connect – from inverter
to – of battery terminal) to prevent reverse polarity.
• When you are using the inverter and you hear a beeping sound coming from the inverter, this
means your 12V battery is low. To recharge, disconnect the inverter from your battery and turn on
the engine for 2 to 3 hours.
• When charging your 12V battery using a battery charger, please disconnect the inverter.
• Only operate Class 2 appliances
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Inversor de Streetwize
Streetwize
Streetwize SWINV300 Hoja de especificaciones
Streetwize
Streetwize SWINV500 Manual de usuario
Streetwize
Streetwize SWINV2000 Hoja de especificaciones
Streetwize
Streetwize SWINV150 Hoja de especificaciones
Streetwize
Streetwize SWINV800 Hoja de especificaciones
Streetwize
Streetwize SWINV1500 Hoja de especificaciones
Streetwize
Streetwize SWINV1000 Hoja de especificaciones
Streetwize
Streetwize SWINV3000 Manual de usuario
