STRATOS SCP8000 Manual de usuario

Rev. 1 1215

Polaris RZR

P/N SCP8000

Before you begin, read these instructions TWICE and check to be sure

all parts and tools are accounted for. Please retain these installation

instructions for future reference and parts ordering information.

This Kit Includes:

Ref. Qty. Part Description

A 1 Heater w/mounting bracket

B 1 3 Speed Fan Switch & Knob

C 1 Decal for Fan Switch

D 16’ Heater Hose

E 2 Firewall hose Grommets

F 1 Lg Wiring Harness

G 2 Y-Connector 1”x1”x5/8”

H 8’ Flex Hose

I 1 Defrost Vent

J 3 Square Vents

K 8 Flex Hose Clips

L 1 Vent Bracket

M 2 Screws

N 2 Nuts

O 4 Lg Hose Clamps

P 4 Sm Hose Clamps

Q 1 Inner/Outer Star Washer

R 1 Locking Washer

S 2 Self-tapping Screws

T 4 Templates

Rev. 1 1215

Suggested Tools:

Drill

Hose Pliers

Deburring tool or Sandpaper

1 3/8” Hole Saw

Screw drivers

Hot Knife

Hose Cutter

Voltage Meter/Test Light

Wire Cutter

WARNING: Hot Engine coolant can cause severe burns.

Never open the cap on a hot radiator. Allow the engine to

cool completely before beginning any work.

NOTE: Vent Templates not included with online instructions

Call 844.233.4121 if needed.

Rev. 1 1215

POLARIS RZR INSTALLATION INSTRUCTIONS

Picture 3

Picture 1

Picture 2

Picture 4

1. Put the vehicle in park. Turn Key to “OFF” position and

remove from the vehicle. Never work on a hot vehicle, as

severe burns can occur.

2. Remove Drivers seat. Disconnect the black negative

battery cable from battery. Disconnect the red positive

battery cable from battery.

3. Remove the hood from the vehicle.

4. Remove the two screws in the upper instrument panel and

disconnect the ignition, headlight switch, assessor plug,

AWD switch and any other accessory controls that may

have been added.

5. Remove center storage compartment support bracket.

Then remove the center storage compartment. (Picture 1)

6. Using the firewall heater hose template (Template 1) mark

center of each hole using a sharp punch or awl. From

inside of firewall drill holes using a 1 3/8” hole saw. (Picture

2) Be sure to check on the radiator side of the firewall for

any obstructions prior to drilling.

7. Use mounting bracket template (Template 2) secure

template onto the firewall (Picture 3) and drill 5/16” holes

for bracket screws. Be sure to check for obstructions on

the radiator side of the firewall before drilling.

8. Loosely install hose clamps (P) onto heater hoses (D).

Remove the rubber stoppers from the heater core pipes on

the heater (A) and place hoses on pipes, slide clamps (P)

into position and tighten hose clamps.

9. Attach large wiring harness (F) to fan plug from heater

assembly (A) . Also attach small wiring harness from the

resistor on the heater assembly (A) to the two remaining

plugs in the large wiring harness.

10. Lower the heater assembly (A) into the dash where the

storage compartment support bracket was removed.

(Picture 4)

11. Make sure the straight grill is positioned at the bottom of

the heater assembly (A) and the bracket is next to the

firewall.

12. Fasten bracket to the firewall with screws (M) securing with

nuts (N). Be sure to route all wiring away from any sharp

edges.

13. Route heater hoses through 1 3/8” holes in firewall. Install

grommets (E) onto each hose. A small amount of lubricant

may be used to aid in installation.

Rev. 1 1215

14. Seat grommets (E) into holes of firewall. Make

sure to position hoses so there are no kinks.

15. Route large wiring harness (F) through existing

hole in firewall (Picture 3 shows existing hole)

10. Mark a spot on the radiator hose on the engine

coolant return side. Mark a spot on the radiator

hose on the engine coolant supply side. (Picture 5)

These are your center marks and where you will

place the Y connectors (G).

11. Use 3 sets of hose pliers to displace the engine

coolant and make the radiator hose easier to cut.

Place the 1st set of hose pliers 4” to the left of the

center mark. Place the 2nd set of hose pliers on

the center mark. Place the 3rd set of hose pliers 4”

to the right of the center mark.

12. Place a catch pan under the hose to be cut, to catch

coolant that may be trapped between pliers.

13. Using hose cutters, make a straight cut on the mark

at the 2nd set of pliers. You may need to cut and

remove a section of the radiator hose to maintain

adequate clearance from other components.

Remove the center hose pliers.

14. Install a Y connector (G) with the 5/8” side pointing

upward. Secure with two large hose clamps (O).

(Picture 6).

15. Measure the length needed for heater hoses to the

Y connector (G) and trim off any excess heater hose

length with hose cutters.

18. Install heater hose from heater assembly (A) to

5/8” end of the Y connector (G) and secure with

small hose clamp (P). Clamp heater hose near Y

connector (G) with hose pliers, before removing

hose pliers from radiator hose .

19. Repeat steps 11 through 18 on the other marked

radiator line.

20. Check all hose connections making sure all hose

clamps are tight.Remove all hose pliers.

Picture 5

Picture 6

Rev. 1 1215

21. Locate a position on the upper instrument panel to

install the defrost vent (I). Secure the template (3)

in place and cut the instrument panel along the

dotted line. Be sure to check for clearance and

obstructions before cutting. Place two flex hose

clips (K) on the backside of the vent and install

defrost vent.

22. Secure the templates (4) on the panel above the

center console to install two of the square vents (J).

(Picture 7) Cut the console along the dotted line.

Place two flex hose clips (K) on the backside of

each of the vents and install square vents.

23. Locate a space on the side firewall behind the

steering column on the driver’s side for heat at

your feet. Use two self-tapping screws (S) to

mount the square vent bracket (L). (Shown in white

in Picture 8).

24. Place two hose clips (K) on the backside of the third

square vent (J) and place in the vent bracket (L).

(Picture 9 in black).

25. Cut flex hose (H) into four lengths. Attach these

four flex hoses (H) to the pre-clipped heater ducts

on the heater assembly (A) (Picture 10).

27. Attach flex hoses (H) from heater assembly (A) to

the vents, as follows. The two flex hoses closest to

the console panel connect to flex hose clips on the

two square vents in the center console. The upper

right flex hose connects to the flex hose clips on

the defrost vent in the upper instrument panel and

upper left flex hose connects to the flex hose clips

on the driver’s side square vent. Use wire cutters

on flex heater hose to size to fit.

28. Use 11mm drill and make a hole in the side of the

instrument panel for the fan switch. Be sure to

check for any obstructions before drilling. Place

the star washer (Q) on the fan switch (B). Insert

fan switch (B) into the hole and secure with locking

washer (R). (Picture 11)

29. Place the decal (C) over the switch and place knob

(B) on the switch. (Picture 12). Connect the wiring

harness to the rear of the fan switch.

Picture 9

Picture 10

Picture 7

Picture 8

Rev. 1 1215

Picture 13

Picture 11

30. Reconnect the battery. Do NOT Start Engine.

31. Locate the Terminal or Fuse Block. (Picture 13 is

typical). The wiring harness (F) has 3 wires, a

red power wire, a yellow ignition/accessory

wire and a black ground wire. Using a Voltage

meter or Test Light, with the ignition switch off,

test the terminals in the terminal block. The

terminal that is live is for the red wire. Next,

turn the ignition on (Do not start engine) and

re-test the remaining terminals. The next live

terminal is for the yellow wire, while the dead

terminal is for the black ground wire. Connect

the wiring harness (F). Turn ignition off and re-

test the yellow wire, to ensure that you have

connected it correctly (ie. to a terminal that

shuts off when the ignition is turned off).

32. Remove the radiator cap. Fill cooling system

with coolant and BLEED AIR* FROM THE

SYSTEM according to the service manual.

33. Run engine through two complete radiator fan

cycles. Allow to cool and top off engine coolant

recovery bottle

34. Periodically check coolant during the first

couple hours of operations.

Picture 12

We offer an Air Bleed Kit

(SCP6105 &6106) to quickly and

easily bleed your coolant system.

* For a quick and easy way to bleed

your coolant system check out our

website at www.stratosclimate.com

Tabla de contenidos

Otros manuales de Calentador de STRATOS

STRATOS

STRATOS SCP7106 Manual de usuario

Manuales populares de Calentador de otras marcas

oventrop

oventrop Regucor Series Manual de usuario

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manual de usuario

ELMEKO

ELMEKO ML 150 Manual de usuario

BN Thermic

BN Thermic 830T Manual de usuario

KING

KING K Series Guía

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guía de inicio rápido

Well Straler

Well Straler RC-16B Manual de usuario

EUROM

EUROM 333299 Manual de usuario

Heylo

Heylo K 170 Manual de usuario

Eterna

Eterna TR70W Manual de usuario

Clarke

Clarke GRH15 Manual de instrucciones

IRSAP

IRSAP The Radiator Company Ovali Manual de usuario

Empire Heating Systems

Empire Heating Systems WCC65 Manual de usuario

Wetekom

Wetekom 92 86 43 Manual de usuario

Desa

Desa SPC170-F Manual de usuario

Watlow

Watlow Watrod Electric Tubular Heaters Manual de usuario

Haverland

Haverland ECO-DRY GPS Series Manual de lista de piezas

Stelpro

Stelpro ASILVC2060 Series Manual de usuario