Storm Manufacturing Group, Inc. / 23201 Normandie Ave. / Torrance, CA 90501 / TEL: 800.210.2525 / FAX: 800.997.0500 / www.BucknerSuperior.com
length is 2 days. To change the calendar length to 7 days, key in 7 then press ENTER. The display will then flash PE:
7 to indicate that the calendar length has been changed to 7 days.
8) How do I change the current time of day that is displayed when dial is in AUTO?
Turn the dial to any program number and key in the current time (if PM press PM key) then press TIME key.
Return dial to AUTO position and the correct time will appear on the display.
9) How can I determine what stations are included in a program and the watering duration of each station?
Turn the dial to the desired program. Press the STN WATER TIME key. The number that appears on the display
is the combined watering duration for all stations assigned to the program. Next, press the STN WATER TIME key a
second time. The display will scroll thru all assigned stations in sequence first showing the station number followed
by the station watering duration.
To view the watering duration of a particular station, key in the station number then press STN WATER TIME
key and the station watering duration will appear. If no station watering time appears, then that station has not
been assigned to the program.
10) How can I determine what the cycle start time is for a program?
Turn the dial to the desired program and press CYCLE START key. The controller will display in sequence all
programmed cycle starts, first showing the cycle start number followed by the cycle start time, and then the cycle
end time.
11) When I checked the cycle start time for a program by pressing the CYCLE START key it showed two cycle start
times, but I only assigned one cycle start. How is this possible?
The first time that appeared on the display is the cycle start time. The second time that appeared on the
display is the cycle end time, not a second start time.
12) How can I check what water days are assigned to a program?
Turn the dial to the desired program and press the WATER DAY key. The display will scroll the water days as
“On” days.
13) How do I delete a water day?
Turn the dial to the desired program and key in the day you want to delete, then press the SKIP DAY key.
14) How do I change the watering duration of a station?
Turn the dial to the desired program. Key in the station number and press the STN WATER TIME key. Next, key
in the desired watering duration and press ENTER.
15) How do I delete a station from a program?
Turn the knob to the desired program. Key in the station number and press the STN WATER TIME key. Next, key
in 0 and press ENTER.
16) I have watering set for Monday, Wednesday, and Friday but it’s watering on Tuesday, Thursday, and Saturday.
What’s wrong?
TODAY is set on the wrong day. To set on the correct day, turn the dial to any program and key in the current
day (1=SUN, 2=MON, 3=TUE, etc) and then press the TODAY key.
17) I programmed a loop cycle to begin at 8:00AM and end at 6:00PM. After completing the programming steps at
1:00PM, I returned the knob to AUTO and expected the cycle to start. Why didn’t it start?
The program will not start automatically until the next scheduled start time which is 8:00AM the following day.
However, the program can be stated semi-automatically at any time by turning the knob to the loop program, keying
in the lowest numbered station assigned to the program and then pressing the MANUAL ON/OFF key. The program
will operate until the end of the loop and then shut off automatically.
18) I programmed a loop cycle with all stations set to water for 10 seconds. However, during a cycle each station
runs for 6 seconds then shuts off for 4 seconds before the next station turns on. Why is this?
The controller has a feature enabling you to set a delay of 1 to 59 seconds between the time one station shuts
off and the next station turns on. The delay time is subtracted from the previous station's runtime. If a 4 second
