STEINEL IS 360 W Manual de usuario
Installation Instructions
Ceiling Mount Outdoor
Occupancy Sensor
Consignes d’installation
Détecteur de présence
Montage sur plafond à l’extérieur
IS 360 W
IS 360 B
English
Made in
Romania
Français
RoHS
Compliant
2
www.steinel.net (800) 852-4343
Product Overview
120V
60Hz PIR
IP54 360°
Ceiling
mount
Applications
• Exterior: entryways, carports,
balconies, building soffits
• Interior: corridors, vestibules,
garages
Intended uses
• Suitable for automatic switching
of lights
• NOT suitable for alarm systems
In this package
• IS 360 sensor
• Accessory pack (2 fastening
screws, 2 anchors, 2 rubber
plugs, 3 wire nuts, 2 lens
shrouds)
• Installation instructions
Needed for installation
• For exterior installation:
1 NEMA watertight round
4-inch junction box
• For interior installation:
1 octagon 4-inch junction box
Note: mounting screw holes are
3.5” apart
IS 360 Installation Overview
Environmental considerations
• Weather can affect operation
of the sensor. Strong gusts of
wind, snow, rain and hail can
cause switching errors, since the
sudden temperature changes
cannot be distinguished from
heat sources.
WARNING
• Turn power off at the circuit breaker before installing the sensor
• Sensor must be installed and used in accordance with appropriate
electrical codes and regulations
• Installation by a qualified electrician is recommended
3
www.steinel.net (800) 852-4343
Voltage 120 VAC, 60 Hz
Load rating 0-600 watt Tungsten
0-300 watt Ballast
Time delay 10 sec to 15 min
Light level .2 - 200 footcandles
2 - 2000 lux
Coverage 360°, up to 40
foot reach
Environment Rated IP54 raintight
-4°F to +122°F
-20° C to +50°C
Dimensions 3.9 x 4.7 x 4.7 in
100 x 120 x 120 mm
5 year warranty
UL Listed, CSA Approved,
RoHS Compliant
SpecificationsProduct description
The STEINEL IS 360 occupancy
sensor automatically turns lights
ON when presence is detected and
OFF when a space is left vacant,
enhancing security, convenience
and energy savings. The sensors are
raintight for safe, reliable operation
indoors and out.
40 ft 40 ft
40 ft
40 ft 40 ft
Mounting plate
Sensor housing
Decorative ring
(adjustments beneath)
Housing cover
Coverage shroud
Detection lens
1 4
2 5
3 6
1
4
5
6
2
3
4
www.steinel.net (800) 852-4343
Mounting
Fastening screw
Placement guidelines
• Intended for surface mounting
under soffit (exterior) or on
ceiling (interior)
• Ideal outdoor placement for the
IS 360 is under an overhang
• Detection lens must have a clear,
unobstructed view of detection
area
• Ideal mounting height is
8-12 feet
• Backout the 2 fastening screws;
separate sensor housing from
mounting plate.
• Insert the two rubber plugs into the
mounting plate.
• Place the sensor wires through
the knockout in the center of
the mounting plate and connect
electrical wires (see Wiring).
• Align mounting plate with junction
box and secure with j-box screws.
• Realign mounting plate to sensor
housing; secure with fastening
screws.
• Reapply and engage the housing
cover.
(Note: The device housing is not
suitable for field wiring termination.)
Housing cover
Decorative ring
Mounting plate
Sensor housing
Junction box
1
2
4
3
Installation
Ensure use of the correct enclosure
and confirm power is off at the
circuit breaker.
• Remove housing cover. Press
the two indentations on side
of housing cover, turn counter-
clockwise and pull.
5
www.steinel.net (800) 852-4343
Wiring
L
O
A
D
LINE (BLACK)
NEUTRAL
Local OFF
Switch (optional)
HOT
NEUTRAL (WHITE)
LOAD (RED)
When installing, make sure power has
been switched off at the breaker and
check that the circuit is dead with a
voltage tester. The leads consist of
three wires:
Black L IN = hot wire
Red L OUT = switched hot wire for
fixture
L
O
A
D
L
O
A
D
LINE (BLACK)
NEUTRAL
Local OFF
Switch (optional)
HOT
NEUTRAL (WHITE)
LOAD (RED)
LINE (BLACK)
NEUTRAL (WHITE)
LOAD (RED)
White N = neutral wire. Connect N
(white) with the neutral wire (usually
white)
Connect L OUT (red) with the hot wire
of the fixture (usually black.) Connect
L (black) with the hot wire of the
supply lead (usually black.)
6
www.steinel.net (800) 852-4343
Setup & Commissioning
Operation
Test mode
• Ensure that the sensor is in test
mode.
- set time delay to position 1
(minimum setting of 10 sec).
- set light level to position 1
(light level function overridden).
Light LevelTime Delay
The IS 360 operates by turning lights
on automatically when occupancy
is detected and off when the space
is left vacant and the time delay has
elapsed.
The light level feature keeps lighting
off during daylight hours, regardless
of occupancy.
Adding a wall switch provides a
manual override function. While
the switch is ON, the sensor is in
occupancy control mode. Users can
turn the switch OFF at any time to
keep lights OFF.
• Turn power ON at the circuit break-
er (lights will turn ON). After a warm
up period of up to one minute,
lights will turn OFF if the sensor
does not detect motion.
• Walk in view of sensor, lights should
turn ON. Be still for 10 sec. and lights
should turn OFF.
7
www.steinel.net (800) 852-4343
.2 - 200 fc
10 sec - 15 min
Typical mounting height for the IS 360
is 8 to 10 feet
Setup & Commissioning (cont’d)
Coverage size
With an installation height of 8 to
10 feet, maximum reach is up to
40 ft. If needed, the detection zone
can be adjusted (see below).
Coverage may vary depending on
mounting height and environmental
conditions.
Light level
The light level feature allows light-
ing to remain OFF during daylight,
regardless of occupancy. Daytime
operation is at 200 footcandles
(factory setting) with the adjust-
ment set at position 1.
Nighttime operation, .2 footcan-
dles, is at position 6.
Time delay
Time delay is the period of time
lights remain ON after a space is
left unoccupied. Adjustment rang-
es from 10 sec. (factory setting)
to 15 min.
After setup and commissioning
tests are complete, adjust the time
delay and light level settings to fit
your application needs.
8
www.steinel.net (800) 852-4343
Shrouds, supplied with each unit,
snap in place, allowing users to adjust
coverage as needed. Shrouds cover
any desired number of lens segments
and reduce the reach. Undesired de-
tection of cars, pedestrians, etc. out-
side the desired detection range can
be eliminated.
The shrouds can be divided vertically
or horizontally along the grooved
divisions, or cut with scissors.
After removing the decorative ring,
the shrouds are suspended on the
upper part of the sensor lens.
The decorative ring is subsequent-
ly reapplied and the shrouds are fixed
firmly in place.
Coverage adjustment - shrouds
40 ft
40 ft
15 ft
15 ft
15 ft
15 ft
9
www.steinel.net (800) 852-4343
The sensor’s reach will vary depending on
the user’s approach. The fine tune adjustment
can change the coverage angle to achieve
detection earlier.
Coverage adjustment - fine tune
rotation
Fine tune adjustment is also possi-
ble by turning the sensor housing
± 10°. This alters the angle of the
coverage zone.
For example, in an application where
users are not detected soon enough,
adjusting the sensor housing 10°
ensures that the user’s motion enters
a switching zone sooner, thus turning
lights on sooner.
ca.5 m
ca.12 m
16 ft 40 ft
10
www.steinel.net (800) 852-4343
Troubleshooting
No power at the sensor ■breaker has tripped;
light switch is in OFF
position
■short circuit
■reset breaker, turn
light switch to ON
position, check wiring
with voltage tester
■check for proper
wiring connections
Lights do not switch ON ■light level setting is in
nighttime mode during
daytime operation
■lamp burned out
■power is OFF
■breaker has tripped
■detection zone not
correctly adjusted
■adjust light level
setting
■replace lamp
■turn power ON at
circuit breaker
■reset breaker
■readjust
Lights do not switch OFF ■abundant heat from
the fixture is within
detection zone and
keeps lights ON as a
result of temperature
change
■readjust zone or apply
shroud
Lights keep switching
ON/OFF
■switched ON light is
within detection zone
■animals moving in
detection zone
■adjust detection zone
or apply shrouds,
increase distance
■adjust zone or apply
shrouds
Lights switch ON without
obvious movement
■wind is moving trees
and bushes in the
detection zone
■cars in the street are
detected
■sudden temp changes
due to weather (wind,
rain, snow) or exhaust
air from fans or open
windows
■adjust zone or apply
shrouds
■adjust zone or apply
shrouds adjust
■adjust detection zone
or install in a different
place
Malfunction Cause Remedy
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios de STEINEL
STEINEL
STEINEL RS PRO Series Manual de usuario
STEINEL
STEINEL IS 300 Manual de usuario
STEINEL
STEINEL IS 1 Manual de usuario
STEINEL
STEINEL True Presence Manual de usuario
STEINEL
STEINEL IS 2180-5 Manual de usuario
STEINEL
STEINEL LuxMaster BLS Manual de usuario
STEINEL
STEINEL IS 2180 ECO Manual de usuario
STEINEL
STEINEL Studioline 400 Manual de usuario
STEINEL
STEINEL IR 180 UP easy Manual de usuario
STEINEL
STEINEL HBS 200 Manual de usuario
STEINEL
STEINEL LiveLink HF 3360 Manual del propietario
STEINEL
STEINEL IS 2180-2 Manual de usuario
STEINEL
STEINEL L 115 S Manual de usuario
STEINEL
STEINEL Studioline IS 300 Manual de usuario
STEINEL
STEINEL True Presence KNX Manual del propietario
STEINEL
STEINEL IS 3180-24 Manual de usuario
STEINEL
STEINEL L 86 Series Manual de usuario
STEINEL
STEINEL L 330 S Manual de usuario
STEINEL
STEINEL SensorSchalter IR 180 UP Manual de usuario
STEINEL
STEINEL IR Micro LiveLink Manual del propietario
