Status Pro Level Precision Manual de usuario

Another fine solution by

Precision Level ystem

User Guide

BA 1044 E 07/15

2Status Pro – µLevel User Guide

User Guide – English

Level ystem (BG 840100)

We would like to congratulate you on the purchase of your Status Pro µLevel Precision

Level System. Before initial usage you should carefully read the safety instructions as well

as the user guidelines contained in this manual. We wish you every success when using

this Measurement Instrument. Please note: User Manuals can be amended when improve-

ments or changes to the product range have been carried out.

Use the link below to make sure you have the most up to date

version of your User Manual: www.statuspro.com.

The System i cludes the followi g:

• 1 x BT 840100 µLevel single

• 1 x BT 840110 Case for µLevel

• 1 x BT 840120 Foam inlay for µLevel Case

• 1 x BT 840170 Optional: Software Smartlevel Pro + Cable Kit

Please make sure that your system is complete

and all components are in good condition.

Content

1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. NOTES ON SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.1 Declaration of confomity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2.2 Advice on batteries / rechargeable cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Instrument care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CONTENT

Status Pro – µLevel User Guide

2.5 Liability Exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Batteries / rechargeable cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Button panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.3 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4. OPERATION GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 Temperature Constant before Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 The Meaning of the Readings Displayed at Measuring Mode . . . . . . . . . . . . . . . . . 12

4.3 Level Inspection and Adjustment for Working Surface . . . . . . . . . . . . . . . . . . . . . . . 13

4.4 Straightness and Flatness Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.5 Use the Store Function of the Level Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.6 Measurement Connecting with Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

5. ADJUSTMENT OF THE APPARATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.1 Relative Zero Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.2 Absolute Zero Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5.3 Scale of the Apparatus Displayed Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.4 Renew the Leave Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

6. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7. LEVEL ANDROID SOFTWARE (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.1 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.2 µLevel registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

7.3 Differential (Delta)- and Rightangles- resultant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

7.4 Disconnect and exit the app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

. SMARTLEVEL PRO SOFTWARE (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8.1 Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

8.2 Program Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8.3 Measuring icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8.4 Measuring object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

9. PRODUCTS UND SERVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4Status Pro – µLevel User Guide

INTRODUCTION

1. Introduction

µLevel is produced in Far East with the quality standard ISO 9001 since 1993. It is a high

accuracy measuring product adopting sensitive capacitance sensor, as well as using

SCM as controller. It is widely used for the inspection of the flatness, straightness of

products, installation and adjustment of precision machine tools, Machining Centers,

Three Coordinates Measuring Machines. Meanwhile its measured data could be input

computer directly, cooperating with measuring software, the flatness and straightness of

products could be measured automatically, and calculated measuring result and graph

could be output and printed. Ergonomical Design, self-contained functions, will bring your

measur-ing work beat all surprise and kilter.

As this Digital Level Meter has a lot of functions, carefulness reading of the operation

manual before using could guide you making full use of the various functions.

2. Notes on safety

2.1 Declaration of conformity

This product conforms tot he EMC Directive 2004/I08/EC and of the, 73/23/EC of CE

Directive.

Instrument Type: level measuring Instrument

The radio Emissions correspond to part 15 of the FCC Directive.

Health and safety:

–EN 50371:2002

–EN 60950-1:2006 + A11:2009 + A1:2010 (EN 60950-1:2011-01)

and/or IEC 60950-1:2005 (2nd Edition) + A1:2009

NOTE ON AFETY

Status Pro – µLevel User Guide

2.2 Advice on batteries / rechargeable cells

If the equipment is being stored for a longer period of time or being powered using Mains,

then the batteries/rechargeable cells should be removed to prevent damage of the

instrument through leakage.

When using rechargeable cells always observe the specific charging procedures for the

cells.

Rechargeable cells can be recharged around 1000times when treated correctly, but there

is no guarantee!

2.3 Instrument care

Your measurement instrument is designed for use in an industrial environment and can

withstand water splashes or light spray as well as dust. Clean the equipment using a soft

cotton cloth and a mild soap solution. Laser apertures as well as well as sensor areas

should only be cleaned using a soft, dry and dust-free cloth. Do not use paper towels to

clean glass surfaces as they could scratch. Avoid contact with grease, oil or oil-based

solutions when handling the equipment.

Caution!

Do not try to recharge normal batteries. Do not expose batteries

or rechargeable cells to fire or excess heat (Danger of explosion).

Do not mix batteries and rechargeable cells.

Always use batteries and cells of the same kind.

Do not mix old and new batteries or cells.

Note

Help to protect the environment! Empty batteries do not belong in

the household waste disposal system. Only deposit empty or

damaged cells at a collection point specially designed for this

purpose.

6Status Pro – µLevel User Guide

NOTE ON AFETY

2.4 Calibration

To guarantee measurement accuracy, and reliable operation of your Status Pro

Measurement System, it is of utmost importance that the recommended service intervals

be adhered to. The System should be checked for serviceability, and re-calibrated by the

Status Pro workshops every 12 months.

Within the scope of the service checks, the complete system will also be examined for

possible wear or damage, as well as receiving any software updates.

The date of the next service check for your equipment is stamped on the Status Pro cali-

bration sticker.

To ensure trouble-free processing of the service and calibration checks, simply fill in the

form you will find using the following link www.statuspro.com.

2.5 Liability Exclusion

The Status Pro GmbH does not accept responsibility for damage incurred through incor-

rect use or handling of the equipment. To ensure correct usage, a founded knowledge of

the equipment is essential. It is of the utmost importance that you read and understand

the Handbook!

No responsibility will be accepted for damage incurred through ignorance or disregarding

of the operating instructions.

Advice

To be able to identify the equipment when seeking advice always

quote the serial number of the equipment. The Manufacturer does

not accept any responsibility for damage incurred through incorrect

maintenance carried out by non-authorised personnel.

GETTING TARTED

Status Pro – µLevel User Guide

3. Getting started

3.1 Batteries / rechargeable cells

1. Open the cover of the battery storehouse under the handle.

2. Put in 4 pieces of “AA”5# battery as per the positive and negative

poles marked on the cover of the battery storehouse.

3. Close the cover and check the battery installation have been OK.

Remi di g:

• When begin to blinking, all of the batteries should be replaced.

• New batteries could not be mixing used with old batteries.

• If the apparatus will not be used for a long time, the batteries

should be taken out in case of the leakage of the batteries rust

other components, which may cause the apparatus can not work.

• New batteries could not be mixing used with old batteries.

3.2 Button panel

Induction Control Panel

Display

Handle

Power on-off

Data transmission socket

Storehouse for batteries

Measuring base

Housing

SCL / RST key

Control box

8Status Pro – µLevel User Guide

3.3 Display

Start-up I spectio :

Switch on the power, displayer will show measuring phase position. The measuring

unit will be same as what it was before the apparatus being switched off.

Display for measuring unit in mm Display for measuring unit in inch

Measurement with 1µm/m resolution

Measurement with 10µm/m resolution

Zero Setting

Voltage

Temperature

Read stored data

Delete stored data

Scale

Restoration

Serial number

Serial number for current data

The last data stored

Display of measurement readings

Power low

Tilt direction display: right side high

Tilt direction display: left side high

Minus display

Radix point

Measuring unit: second

GETTING TARTED

Status Pro – µLevel User Guide

Touch gently the Mode key and adjust it to volt-

age , the LED displayer will show current voltage.

If the voltage is lower than 4 V, Low Voltage warning

will flash.

Reminding

➜If no shows or show abnormally after the power being switched on, please switch off

the power at once. After eliminate the trouble, start-up could be done.

Touching Key

After the apparatus is switched on, touch gently Mode key or , the

LED displayer will show the following list: II, I, Zero Setting, Voltage,

Temperature, Reading, Delete.

Fine adjustment, zero setting; reading, reset (see Function Choice).

Touch the button, radian unit (mm/m) and angle unit (second) could be

transformed. This function could only be available at measuring phase and

, no use at other measuring phase.

(1) When choose radian unit to measure, it display the measuring unit “mm/m”.

It expresses the gradient height difference at length of 1 meter. In the practice

inspection, as the span of the used stride bridge is different, the reading a´Ifor every

inspected point at the E-level meter could be transformed to line value ai(µm) by the

following formula

ai= 1000TL a´I(µm)

T ------ Resolution of the E-level meter (µm)

L ------ Span of stride bridge (mm)

(2) When choose angle unit to measure, LED will show the angle value (˝).

GETTING TARTED

Function Choice

After the apparatus is switched on, touch gently Mode key or could choose

different functions.

Measuring Phase

This is a high precision measuring phase. The resolution of measur-

ing phase II of WL11 Digital Level Meter is 0.001mm/m, suit to

inspect the flatness, straightness of products with precision grade “00”. The resolution of

measuring phase II of WL10 Digital Level Meter is 0.005mm/m, suit to inspect the flatness,

straightness of products with precision grade “0”.

Measuring Phase

This is relative lower precision measuring phase. The resolution of

measuring phase I of WL11, WL10, WL9 Digital Level Meter is

0.01mm/m, suit to inspect the flatness, straightness of products with

precision grade“1”.

Reminding

➜Different resolutions of different measuring phase suit to different accuracy

inspections. Please choose proper product and measuring phase accordingly.

➜The higher measuring phase limit the temperature and environment strictly.

If environment and temperature could not be ensured as requested, the apparatus may

be not stabilized.

Zero Setting

Being at this mode, press button and , the Level Meter

zero position could be set.

(1) At the working surface being inspected, set Zero at any position (relative zero position).

(2) Absolute zero setting

(3) Nice zero setting could be available by pressing the number descending or ascending.

Reminding

➜Regarding to the detailed process of zero setting for Digital Level Meter, please read

Segment “Apparatus Adjustment” on page 16.

Voltage

Function of measuring the power voltage automatically. LED

displayer shows the voltage (V) of the batteries being in use. When

the voltage is lower than 4V, low voltage warning will flash.

10 Status Pro – µLevel User Guide

GETTING TARTED

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Status Pro

Status Pro

Status Pro mLine F1 Manual de usuario

Status Pro

Status Pro T430 Manual de usuario

Status Pro

Status Pro Belt Tension Pro Manual de usuario

Status Pro

Status Pro mLine F1 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario