StarTech.com ST100SLP Manual

10/100 Mbits/sec PCI Ethernet Network

Card

ST100S

ST100SW

ST100SLP Instruction Guide

The Professionals’ Source For Hard-to-Find Computer Parts

NETWORK ADAPTER

* Actual product may vary from photo

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Connecting Your Card to Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Installing the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Monitoring Your Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tips for Setting Up Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Introduction

Thank you for purchasing a StarTech.com10-100 Mbits/sec PCI Ethernet card. This

reliable, high speed network card lets you connect your computer to your Ethernet LAN

and experience super-fast transfer speeds of up to 100Mbits/sec. Full duplex support

means that the card can simultaneously transmit and receive information at these high

speeds. The card is a snap to install and set up and is fully Plug and Play compatible in a

wide range of operating environments.

Features

•Complies with 10BaseT Ethernet and 100BaseTX Fast Ethernet standards

•Capable of full- and half-duplex communications

•Complies with Plug and Play specifications

•Auto-negotiation function determines the optimal transmission rate

•Supports 32-bit PCI Bus Master for high performance and low processor utilization

•Backed by StarTech.com's lifetime warranty

Before You Begin

To ensure a quick and easy card installation, please read through this section carefully

before attempting to install the card.

System Requirements

•An IBM compatible notebook computer with a Pentium processor

•An open PCI slot

•One of the following operating environments: Windows XP/ME/2000/98/95,

Windows NT, Linux, NetWare 3.x/4.x, Lan Manager, TCP/IP software

•ST100SW ONLY: To take advantage of the Wake-On-Lan feature, your

motherboard must be equipped with ACPI/Wake-On-Lan capabilites. Consult your

motherboard user guide or contact the manufacturer for information.

WARNING! PCI cards, like all computer equipment, can be severely damaged by static

electricity. Be sure that you are properly grounded before opening your computer case or

touching your PCI card. StarTech.com recommends that you wear an anti-static strap

when installing any computer component. If an anti-static strap is unavailable, discharge

yourself of any static electricity build-up by touching a large grounded metal surface

(such as the computer case) for several seconds. Also be careful to handle the PCI card by

its edges and not the gold connectors.

Contents

This package should contain:

•1x PCI Ethernet Adapter card

•1x driver disk

Installation

This section will guide you through the installation of your card and the related

software. Please read through the instructions carefully and complete each step in the

order listed.

Installing the Card

1. Make sure that your system is unplugged and you are grounded.

2. Remove the cover of your system (see your computer's user manual for details, if

necessary) and gently turn your computer onto its side.

3. Locate an empty PCI slot (usually white in colour) and remove the metal plate that

covers the rear bracket. You may need a Phillips screwdriver to perform this step.

Hang on to the screw! You will need it to secure the card later.

4. Gently insert the card into the empty slot, making sure it is firmly seated.

5. Secure the card in place using the screw you removed in Step 3.

6. (ST100SW ONLY) Connect the Wake-On-LAN (WOL) connector to the WOL plug on

your motherboard. Consult your motherboard user guide for information, if

necessary.

7. Put the computer case back on.

Connecting Your Card to Your Network

Depending on how you are planning on using the card, the device you are connecting it

to and the type of cable you need may differ. To take advantage of the NIC’s 100

Mbits/sec capacity, it is recommended that you always use at least Category 5 Ethernet

cable. If you are unsure of the type of cable required for your device, consult your device

manufacturer.

NOTE: StarTech.com carries a wide range of Ethernet cables in various colors and

lengths. For more information on these products, as well as tips and ideas for setting up

and running your network, visit http://www.startech.com and click on the Networking

tab near the top of the screen.

•If you are connecting your computer directly to another computer, you need to use a

crossover cable.

•If you are connecting your computer to a hub or switch, you should use a straight-

through cable.

•If you are connecting your computer to the Internet via a DSL or cable modem, you

should use the cable recommended by the modem manufacturer.

Installing the Drivers

NOTE: Windows XP will automatically detect the new hardware and install the

necessary drivers without any user input.

The following are installation instructions for Windows OS only. If you are using Linux,

Netware, or any other supported environment, consult the driver installation instructions

available in text form on the driver disk.

The most recent drivers for your Ethernet adapter are available as a free download from

our website. Visit www.startech.com and click on the Downloads link for information.

Depending on your version of Windows and the configuration of your system, the

instructions that appear on your screen might not be identical to the instructions below.

Windows 2000/ME/98

1. Windows will automatically detect the new hardware. Click Next.

2. Choose “Driver from disk provided by hardware manufacturer”.

3. Insert the driver disk into your disk drive and specify the following path (where

“A:\” is the location of your driver disk):

• Windows 2000: A:\WIN2000

• Windows ME: A:\WINME

• Windows 98: A:\WIN98

4. You may be required to insert your Windows installation disk. Follow the remaining

prompts and reboot your computer when prompted.

Windows 95

1. Windows will automatically detect the new hardware. Click Next.

2. Select “Driver from disk provided by hardware manufacturer.”

3. Insert the driver disk into your disk drive and specify the following path (where

“A:\” is the location of your driver disk):

•A:\WIN95

Windows NT 4.0

1. From your Control Panel, double-click on the Network icon.

2. Choose Add Adapters and select “<Other> Requires disk from manufacturer.”

3. Insert the driver disk into your disk drive and specify the following path (where

“A:\” is the location of your driver disk):

• A:\WINNT4

4. The “Select line speed” dialog box will appear. The default is “Auto”, where the

adapter will auto-detect the line speed. You can choose to set the value to 10 (half- or

full-duplex) or 100 (half- or full-duplex) Mbps if you so choose.

5. The “Input Ethernet ID” dialog box will appear. This option is only required if you

have more than one Fast Ethernet adapter on the computer. Choose “Skip” if you

have only one adapter installed. If you are adding more than one Fast Ethernet

Adapters, consult the Msnt.txt file located in the Txt\Ms folder for additional

instructions.

6. The “Bus Location” dialog box will appear. If your machine contains more than one

hardware bus, please select the Bus Type and Bus Number where the network

adapter is installed.

7. Follow any additional on-screen prompts and reboot your computer to complete the

installation process.

Monitoring Your Card

The LEDs on the front of the card are the best indication of the card’s activity.

If neither Link/Activity LED is lit, there is a connection error. Make sure that all devices

are turned on and that the network cable is properly connected at both ends. Also make

sure that your network cables comply with EIA/TIA 568 and Category 5 specifications.

If problems persist, power down all devices and disconnect all plugs. Wait at least ten

seconds then plug the devices back in and power them up.

LED Color Status Description

10M/Link/Activity Yellow On Card is in 10Mbits/sec mode

Blinking Network activity

100M/Link/Activity Green On Card is in 100Mbits/sec mode

Blinking Network activity

Tips for Setting Up Your Network

For information and help on setting up your network, please consult the manufacturer of

your operating system. The following is for tips and troubleshooting purposes only and

is intended for Microsoft users on a local area network.

Make sure your computers are configured properly

For your convenience, you should configure each of your computers so that they can

“see” each other and share devices and files. To do this, you have to make sure that the

following have been installed on your computers:

•Client for Microsoft Networks

•TCP/IP (Internet Protocol)

•File and Print Sharing

These clients, protocols, and services can be found in the following locations:

Windows XP

1. Click on Start, then click My Network Places.

2. Click View Network Connections in the Network Tasks box.

3. Right-click on Local Area Connection and choose Properties.

Windows 2000

1. Click on Start, then Settings, then Network and Dialup Connections.

2. Double-click Local Area Connections and click the Properties button.

Windows Me/98/95

1. Click on Start, then Settings, then Control Panel.

2. Double-click on Network.

NOTE: If you need to add any of the following components, check your Windows

documentation for details.

Make sure all your computers are on the same workgroup

To be able to communicate properly with each other, each computer must be located on

the same workgroup. Each computer within a workgroup must have a unique name. To

ensure compatiblility between each version of Windows, keep your computer names

under 13 characters long.To view, add, or edit your computer’s name, do the following:

Windows XP

1. Click Start and then Control Panel.

2. Double-click System then click on the computer name tab.

Windows 2000

1. Click on Start, then Settings, then Control Panel.

2. Double-click on System.

3. Click on the Network Identification tab.

Windows Me/98/95

1. Click Start, then Settings, then Control Panel.

2. Double-click Network, then click the Identification tab.

Make Sure Your Sharing is Set Up Properly

1. Go to your network dialog box using the procedure explained under “Make sure

your computers are configured properly.”

2. Click on File and Print Sharing.

3. Choose whether you want to install one, both, or neither of these options. Click OK.

4. Decide what files or folders you want to share. You can call up sharing options by

right-clicking on a file or folder and choose “Sharing” (Windows 2000/Me/98/95) or

“Sharing and Security” (Windows XP).

NOTE: If you are having any difficulties setting up or using your network, please

contact your operating system vendor.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Tarjeta PCI de StarTech.com

StarTech.com

StarTech.com PCISOUND5LP Manual de usuario

StarTech.com

StarTech.com PEXESATA1 Manual de usuario

StarTech.com

StarTech.com PEXUSB311AC2 Manual de usuario

StarTech.com

StarTech.com PCI420USB Manual de usuario

StarTech.com

StarTech.com PLATEIDE2CF Manual de usuario

StarTech.com

StarTech.com MPEX4S552 Manual de usuario

StarTech.com

StarTech.com PCI2S1P2 Manual de usuario

StarTech.com

StarTech.com PEXUSB3S25 Manual de usuario

StarTech.com

StarTech.com 6P6G-PCIE-SATA-CARD Manual de usuario

StarTech.com

StarTech.com PCI4S9503V Manual

StarTech.com

StarTech.com PCI1P Manual de usuario

StarTech.com

StarTech.com PEXUSB312C Manual de usuario

StarTech.com

StarTech.com PCI3UV22F Manual de usuario

StarTech.com

StarTech.com PEXUSB312EIC Manual de usuario

StarTech.com

StarTech.com PEX1PCI1 Manual de usuario

StarTech.com

StarTech.com PEX1000MMSC2 Manual de usuario

StarTech.com

StarTech.com PCISCSIU2W Manual de usuario

StarTech.com

StarTech.com PCI1PECP Manual del sistema

StarTech.com

StarTech.com PEX8S1050LP Manual de usuario

StarTech.com

StarTech.com PCI8S950LP Manual de usuario

StarTech.com

StarTech.com PEX2PECP2 Manual de usuario

StarTech.com

StarTech.com PEXUSB3S3GE Manual de usuario

StarTech.com

StarTech.com PEXUSB3S2EI Manual de usuario

StarTech.com

StarTech.com PEXSATA22 Manual de usuario

Manuales populares de Tarjeta PCI de otras marcas

ERMA

ERMA SSI 1417 Manual de usuario

SIIG

SIIG CyberSerial Dual PCI Instrucciones de montaje

Moxa Technologies

Moxa Technologies CP-102E Manual de usuario

I-Bus

I-Bus IBC2602 Manual de usuario

Exsys

Exsys EX-60102 Manual de usuario

Chelsio Communications

Chelsio Communications T5 Series Manual de usuario

Conrad Electronic

Conrad Electronic 97 46 71 Manual de usuario

Micro Innovations

Micro Innovations USB650A Manual de usuario

KTI Networks

KTI Networks KF-310 Manual de usuario

Asus

Asus SpaceLink WL230 Manual de usuario

SIIG

SIIG SC2475 Manual de usuario

TRENDnet

TRENDnet TEW-703PI Manual de usuario

Belkin

Belkin F5D7000F Manual de usuario

Pericom

Pericom PI7C7100 Manual de usuario

ADLINK Technology

ADLINK Technology cPCI-3548 Manual de usuario

Digium

Digium TE200 Series Manual de usuario

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manual de usuario

Western Digital

Western Digital FireWire PCI Adapter Manual de usuario