StarTech.com PEX1S952 Manual de usuario
PEX1S952
PEX2S952
PEX1S952LP
PEX2S952LP
Native PCI Express RS232
Serial Adapter Card
with 16950 UART
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the equipment and receiver.•
Connect the equipment into an outlet on a circuit different from that to which the receiver•
is connected.
Consult the dealer or an experienced radio/TV technician for help.•
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an
endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to
which this manual applies by the third-party company in question. Regardless of any direct
acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges
that all trademarks, registered trademarks, service marks, and other protected names and/or
symbols contained in this manual and related documents are the property of their respective
holders.
Instruction Manual
i
Instruction Manual
Table of Contents
Introduction.................................................................................... 1
Features ......................................................................................1
Package Contents .......................................................................1
Jumper Configuration ................................................................... 2
Hardware Installation .................................................................... 3
Driver Installation .......................................................................... 3
Windows 2000/XP Driver Installation ..........................................3
Windows Vista Driver Installation ................................................5
Specifications ................................................................................ 7
Technical Support ......................................................................... 8
Warranty Information .................................................................... 8
Instruction Manual
1
Introduction
Thank you for purchasing a StarTech.com PEX1S952/PEX2S952/
PEX1S952LP/PEX2S952LP Native PCI Express 16C950 UART Serial
Card. This dual profile Serial card converts a PCI Express slot into one or
two RS-232 (DB9) serial connections, while relying on a native, single-
chip design for optimal performance and reliability.
Features
128-byte deep FIFO per transmitter and receiver•
Automated in-band software flow control using programmable Xon/Xoff•
in both directions
Automated out-of-band hardware flow control using Tx/Rx/RTS/CTS/•
DSR/DTR/DCD/RI/GND
Compliant with IEEE1284, SPP/EPP/ECP parallel port•
Compliant with PCI Express base specifications revision 1.1•
High Performance Dual Channel Oxford 950 UART•
Native single-Chip, single lane PCI Express•
Selectable power output on pin 9 for the serial port•
High speed RS-232 serial ports with data transfer rate up to•
460.8 Kbps
Package Contents
1 X Serial Card (Low Profile bracket preinstalled on LP models)•
1 X Driver CD•
1 X Instruction Manual•
1 X Low Profile Bracket (PEX1S952 only)•
2 X Low Profile Bracket (PEX2S952 only)•
1 x Full Profile Bracket (PEX1S952LP/PEX2S952LP only)•
Instruction Manual
2
Jumper Conguration
The card is specially designed to allow power output from the ninth pin of
the connector to enable power up of the connected devices without the
use of a power adapter. The card allows user to set each individual port
with 5V, 12V, or RI (no power). The user may also choose to draw the
needed power from the PC’s internal system power supply via an LP4
molex connector.
Instruction Manual
3
Hardware Installation
Turn off the power to your computer.1.
Unplug the power cord and remove your computer’s cover.2.
Remove the slot bracket from an available PCIe slot.3.
To install the card, carefully align the card’s bus connector with the4.
selected PCIe slot on the motherboard. Push the board down firmly.
Optional:5. Connect the LP4 molex power connector from the computer
power supply to the card. Make sure the Jumper settings on the card
are configured properly.
Replace the slot bracket’s holding screw to secure the card.6.
Replace the computer cover and reconnect the power cord.7.
Driver Installation
Windows 2000/XP Driver Installation
At the Add New Hardware Wizard window, click on “Next.”1.
Select the option “Search for the best driver for your devices2.
(Recommended)” and click on “Next.”
Select the option “Specify the location” and type in D:\Uart (where D: is3.
your CD-ROM drive) then click on “Next.”
Click “Next” and then “Finish” respectively.4.
Remove the disc, then select “Yes” to restart the computer for the5.
setup to take effect.
Instruction Manual
4
To verify successful installation on Windows 2000/XP:
From the main desktop, right-click on “My Computer”, then select1.
Manage. In the new Computer Management window, select “Device
Manager” from the left window panel.
Double-click on both “Ports (COM & LPT)” and “Multifunction Adapters”.2.
The Serial Adapter board and additional serial ports (COM ports)
should be displayed when successfully installed. The port is ready to
be connected to new device(s).
Instruction Manual
5
Windows Vista Driver Installation
At the Found New Hardware prompt, click on “Locate and install driver1.
software (recommended).”
When prompted, insert the disc included with your Serial Card and2.
then click “Next.”
A notification will appear informing you that Windows has encountered3.
a problem installing the driver software for your device. Click “close” to
continue.
When another Found New Hardware prompt appears, install the4.
software from the disc included with your Serial Card and then click
“Next.”
A notification will appear informing you that Windows has encountered5.
a problem installing the driver software for your device. Click “close” to
continue.
Instruction Manual
6
To verify successful installation on Windows Vista:
From the main desktop, right-click on “Computer”, then select Manage.1.
In the new Computer Management window, select “Device Manager”
from the left window panel.
Double-click on both “Ports (COM & LPT)” and “Multifunction Adapters”.2.
The Serial Adapter board and additional serial ports (COM ports)
should be displayed when successfully installed. The port is ready to
be connected to new device(s).
Instruction Manual
7
Specications
PEX1S952
PEX1S952LP
PEX2S952
PEX2S952LP
Bus Type PCI Express rev 1.1 (3.3V)
External Ports 1 x DB9 2 x DB9
Internal
Connectors 1 x LP4 molex
Chipset Oxford OXPCIe952
UART 16C950
Power Mode* 5V / 12V / RI (no power)
Maximum Data
Transfer Rate 460 Kbps
Stop Bits 1, 1.5, 2
Data Bits 4, 5, 6, 7, 8
Compatible
Operating Systems
Windows 2000/XP/Server 2003/Vista,
Linux kernel 2.6.11 or later
*Selectable power output on Pin 9 of the serial port
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Tarjeta PCI de StarTech.com
StarTech.com
StarTech.com PCI4S9503V Manual de usuario
StarTech.com
StarTech.com ST1000BTPEX Manual de usuario
StarTech.com
StarTech.com PCI312PUSB/LP Manual de usuario
StarTech.com
StarTech.com PEX1000MMSC Manual de usuario
StarTech.com
StarTech.com PEXHDCAP Manual de usuario
StarTech.com
StarTech.com PEX867WAC22 Manual de usuario
StarTech.com
StarTech.com PEX4S950 Manual de usuario
StarTech.com
StarTech.com PR22GI-NETWORK-CARD Manual de usuario
StarTech.com
StarTech.com PEXUSB312C2 Manual de usuario
StarTech.com
StarTech.com 8STPEXUSB3S25 Manual de usuario
StarTech.com
StarTech.com PEX2S553B Manual del sistema
StarTech.com
StarTech.com PCI2USB Manual de usuario
StarTech.com
StarTech.com PEXSAT34 Manual del sistema
StarTech.com
StarTech.com PEX1000MMSC Manual de usuario
StarTech.com
StarTech.com PEXUSB3S24 Manual de usuario
StarTech.com
StarTech.com PCI2S650PW Manual de usuario
StarTech.com
StarTech.com PCISCSIUW Manual de usuario
StarTech.com
StarTech.com PEXUSB311AC3 Manual de usuario
StarTech.com
StarTech.com PEX1000SFP Manual del sistema
StarTech.com
StarTech.com PCI4S550 Manual de usuario
Manuales populares de Tarjeta PCI de otras marcas
Belkin
Belkin F5D7000F Manual de usuario
Pericom
Pericom PI7C7100 Manual de usuario
ADLINK Technology
ADLINK Technology cPCI-3548 Manual de usuario
Digium
Digium TE200 Series Manual de usuario
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manual de usuario
Western Digital
Western Digital FireWire PCI Adapter Manual de usuario