StarTech.com PCI2S422ISO Manual de usuario
Manual Revision: 01/25/2012
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
PCI2S422ISO
2 Port PCI RS422 RS485 DB9 Serial Adapter Card
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Installation ..............................................................................................2
Installing the Card..................................................................................................................................... 2
Driver Installation...................................................................................................................................... 3
Windows XP/2000..................................................................................................................................... 3
Windows NT ................................................................................................................................................ 4
DOS ................................................................................................................................................................ 5
SCO OpenServer........................................................................................................................................ 8
Technical Specications ........................................................................10
Technical Support ..................................................................................11
Warranty Information............................................................................11
Instruction Manual
1
Introduction
The PCI2S422ISO 2 Port PCI RS422 RS485 DB9 Serial Adapter Card adds two isolated
serial (DB9) ports to a PCI-enabled computer, providing a cost-eective way to connect
your RS422 or RS485 serial devices to a computer doesn’t oer native serial support, or
adding more ports to a computer that does.
To ensure eective data transmission over long distances, including electrically noisy
environments, the card’s ports feature optical isolation.
Ensuring a reliable RS422 or RS485 connection with a broad range of serial devices
including printers, touch screen monitors and more, the adapter card is suitable
for industrial applications and compatible with a broad range of operating systems
including Windows, DOS, Linux and Unix based platforms.
Backed by a StarTech.com lifetime warranty and free lifetime technical support.
Packaging Contents
• 1x PCI Serial Card
• 2x Driver CD
• 1x Instruction Manual
System Requirements
• A computer running Windows XP/Vista/2000/ DOS, Linux or UNIX SCO Open Server
• An open 5V PCI slot
Instruction Manual
2
Installation
Note: In one system, you can install two of these serial cards. Follow the instructions
below to designate each card as either card number 1 or card number 2. Install the
cards one at a time, starting with the card you want to be designated number 1.
Installing the Card
1. Make sure that your system is unplugged and you are grounded.
2. If you are installing two cards in the same system, you must dierentiate between
the cards by using the dip switch on the card. You use dip switch 1 and 2 to set the
card number. When both dip switch 1 and 2 are in the ON position, the card will be
designated card number 1. When dip switch 1 is OFF and dip switch 2 is ON, the
card will be designated card number 2.
You use dip switch 3 and 4 to set each port to either RS-422 or RS-485 mode. Dip
switch 3 corresponds with Port A (marked on the card), dip switch 4 corresponds
with Port B. When the dip switch is in the ON position, the port will operate in RS-
422 mode. When the dip switch is in the OFF position, the port will operate in RS-
485 mode.
3. Remove the cover of your system (see your computer’s user manual for details, if
necessary) and gently turn your computer onto its side.
4. Locate an empty PCI slot (usually white in colour) and remove the metal plate that
covers the rear bracket. You may need a Phillips screwdriver to perform this step.
Hang on to the screw! You will need it to secure the card later.
5. Gently insert the card into the empty slot, making sure it is rmly seated.
6. Secure the card in place using the screw you removed in Step 3 and put your
computer case back on.
7. Turn the computer on.
Instruction Manual
3
Driver Installation
Note: Depending on your operating system and the conguration of your system, the
instructions below may not be identical to what you see on your screen.
Windows XP/2000/Vista
Once you turn your computer on after installing the card, Windows will automatically
detect the new hardware. Follow the onscreen prompts and direct Windows to the
Win2000 folder on the driver disk (Windows 2000 and Windows XP use the same driver).
Notes:
• To change the COM port number: Windows will automatically assign the card a
COM port number. If you need to specify another port number, you can use the
setup utility included with the driver. Go to: Control Panel/System/Hardware/Device
Manager/Multi-Port Serial Adapter/Setup. From here you will be able to set the
target value.
• Each serial card needs an open IRQ for Plug and Play function.
• In Windows XP, the driver for each port will be installed and conrmed. In Windows
2000, the driver will be installed automatically.
Instruction Manual
4
Windows NT
Before you begin the installation, make sure you are logged in as a user with
administrative privileges.
1. Start the Control Panel applet by double-clicking on its icon in the Program
Managers main group.
2. Double-click the Network icon to bring up the Network Control Panel applet.
3. Select Add Adapter. A list of possible adapters will be displayed. Select “Other:
Requires disk from manufacturer.”
4. When prompted for the path, specify the location of the driver for the card
you installed. Depending on your version of the driver disk, the drivers for the
PCI2S422ISO may be found in the P220/NT4 folder. The drivers for the PCI4S422ISO
may be found in the P584/NT4 folder.
5. Follow the onscreen prompts to complete installation. Make sure that the COM port
number does not conict with any other devices in your system.
6. Use the “Binding” function to make more serial ports available. If you do not perform
a binding function, you may not have an extra COM port available in your next boot
procedure.
Notes:
• When installing two cards in the same system, the card with the jumper ON will be
assigned the lower COM port number. The card with the jumper OFF will have the
higher COM port number.
Instruction Manual
5
DOS
When installing multiple cards in DOS, it is important to install the card designated
card Number 1 (with the jumper ON) rst.
1. Change your active directory to the target directory: ex: c:\RAYON
2. Insert the driver disk into the disk drive and copy the DOS les from the driver
diskette: ex: xcopy /s/e/v a:\DOS\*.*
3. Run the driver installation command: ex: c:\rayon\pciport
4. The cards will now be installed in your system. Each card will show the card number
in the system (for the application to specify the target card and target port), the card
model, the card jumper setting (for card number 1 or 2), the IRQ assigned, and the
COM port number for the card.
You may see the following error messages:
• PCIPORT already installed. This means the driver has already been installed.
• Please check the “JP1”. This means that both cards in the system have their jumpers
ON or OFF.
• PCIPORT not in system. There is no card in the PCI slot.
Notes:
• The driver function call description can be found on the DOS driver diskette. There is
also a DEMO program for the user to modify to meet their target application program.
Instruction Manual
6
LINUX
1. Login as super-user (SU) or root.
2. Change your directory to root and copy the driver diskette to the system:
# cd /
# tar xvf /dev/fd0
3. Change the directory to /etc/pciport and run the Install command:
# cd /etc/rayon
# ./Install
4. Follow the prompts to perform the following:
• Choose your card type
• Choose your Linux kernel version
• Rebuild your system
• Exit and reboot with new settings
The device name will be /dev/tty8[1--2] [a--h]
Card Denitions
Card Number Device Name
1 tty81?
2 tty82?
Note: Card 1 is the card with the jumper ON.
Instruction Manual
7
I/O Port Number Denitions
Port Number Device Name
A tty8?a
B tty8?b
C tty8?c
D tty8?d
For example, the device named /dev/tty82b is the device plugged into port B on card
Number 2.
Notes:
• The above installation procedure installs a module type driver. If you can not install
the driver successfully, you may need to use a kernel type driver. With kernel type
drivers, you may need to have the full source le for the Linux system and the source
le must be located in the /usr/src/linux directory. If your source le is in a dierent
location, you must move it or link it to the usr/src/linux directory.
• Each serial card needs an open IRQ for Plug and Play function.
Tabla de contenidos
Otros manuales de Tarjeta PCI de StarTech.com
StarTech.com
StarTech.com PEX8S1050LP Manual de usuario
StarTech.com
StarTech.com 8STPEXUSB3S25 Manual de usuario
StarTech.com
StarTech.com PCI8S950LP Manual de usuario
StarTech.com
StarTech.com PEX4S950 Manual de usuario
StarTech.com
StarTech.com PEXUSB314A2V Manual de usuario
StarTech.com
StarTech.com PCI1394_2 Manual de usuario
StarTech.com
StarTech.com PCISCSI2 Manual de usuario
StarTech.com
StarTech.com PCISAT2F3U4 Manual de usuario
StarTech.com
StarTech.com PCIUSB7 Manual de usuario
StarTech.com
StarTech.com PEXUSB312C Manual de usuario
StarTech.com
StarTech.com PCIUSB3S2 Manual de usuario
StarTech.com
StarTech.com PCISATA2 Manual de usuario
StarTech.com
StarTech.com PEXUSB312C2 Manual de usuario
StarTech.com
StarTech.com PEX8S950LP Manual de usuario
StarTech.com
StarTech.com PCI2S950 Manual de usuario
StarTech.com
StarTech.com PCI1394MP Manual de usuario
StarTech.com
StarTech.com PEX3U3F800 Manual de usuario
StarTech.com
StarTech.com PEXUSB311AC3 Manual de usuario
StarTech.com
StarTech.com PEXUSB312C3 Manual de usuario
StarTech.com
StarTech.com PEXSATA22I Manual del sistema
Manuales populares de Tarjeta PCI de otras marcas
Belkin
Belkin F5D7000F Manual de usuario
Pericom
Pericom PI7C7100 Manual de usuario
ADLINK Technology
ADLINK Technology cPCI-3548 Manual de usuario
Digium
Digium TE200 Series Manual de usuario
Allo.com
Allo.com 2nd Gen E1/T1/J1 Manual de usuario
Western Digital
Western Digital FireWire PCI Adapter Manual de usuario