StarTech.com INFOSAFE SAT2510U2 Manual de usuario

InfoSafe Mobile Drive Enclosure

SAT2510U2

IDE2510U2

Instruction Manual

Actual product may vary from photo

External USB 2.5” Hard Drive Enclosure

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other

Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation and usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installing a drive in the enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installing drivers (Windows 98SE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installing drivers (Mac OS 8.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Using the added drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Powering the added drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Disconnecting the hard drive enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Accessory products from StarTech.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Instruction Manual

IInnttrroodduuccttiioonn

Thank you for purchasing a StarTech.com InfoSafe external hard drive enclosure. This

product allows you to turn virtually any standard 2.5” notebook computer hard drive into a

portable storage solution. The perfect solution for storing multimedia, digital imaging,

audio, and other demanding applications, this product can be installed easily to suit

virtually any storage necessity.

Features

• USB 2.0 compatible

• Backward compatible with USB 1.1

• Requires no external power source

• LED indicates Activity and Power status

Before You Begin

System Requirements

• A computer with an available USB port (USB v.2.0 or v1.1)

• An operating system that supports removable hard drives: Windows

98SE/ME/2000/XP/2003 Server/Vista, Mac OS 8.6 or higher (Note:

Other operating

systems may also support this product; consult your documentation for specific

details

)

Contents

This package should contain:

• 1 x InfoSafe Mobile Drive Enclosure

• 1 x USB 2.0 (Male) to USB Mini B (Male) / Y cable

• 1 x Installation CD

• 1 x Protective pouch

• 1 x Instruction Manual

• 1 x Screw kit

Instruction Manual

IInnssttaallllaattiioonnaanndduussaaggee

Installing a hard drive in the Enclosure

CAUTION:Use caution when installing a hard drive in the enclosure. Excessive shock or

force could damage the drive and/or the enclosure, resulting in data loss.

Always ensure that you are properly grounded when handling a hard drive or the

enclosure tray, since electronic components can be damaged by static electricity. If an

anti-static mat or similar product is not available, ground yourself by touching a computer

case or other metal surface for several seconds before handling any components.

1. Set the hard drive to function in Master mode by adjusting the necessary jumpers,

according to the drive manufacturer’s instruction.

2. Using the included screwdriver, remove the screws fastening the top panel to the

enclosure.

Instruction Manual

Top panel

USB Mini B port

LED Indicator

Bottom panel

3. Attach the 2.5” hard drive to the interface connector (located on inverse of top panel),

ensuring a snug connection. Do not use excessive force, to avoid damaging the drive

and the the enclosure.

4. Insert the interface connector and attached hard drive into the casing.

5. Re-fasten the screws removed in Step 2.

Instruction Manual

Installing Drivers (

Windows 98SE

)

Note: Windows ME/2000/XP/2003 Server and supported versions of Mac OS all support

removable hard drives without additional software. As such, please ensure you have the

most current updates installed. Computers running Windows 98SE need to install

support for USB removable mass storage devices before using the enclosure:

1. Insert the installation CD into your computer’s CD-ROM or compatible optical drive.

2. Double click the My Computer icon on the desktop. Double click the icon for the

computer’s CD-ROM drive.

3. Locate and open the \Win98 folder. Double click on the Setup.exe file, and follow all

prompts to complete installation.

4. Once the software installation has completed, connect the enclosure to the host

computer, using the included USB 2.0 (Male) to USB Mini B (Male) cable. Windows

will notify you that new hardware has been found and installed.

Installing Drivers (

Mac OS 8.6

)

Mac OS 9.0 and above all support removable hard drives without additional software. To

install the necessary software on Mac OS 8.6:

1. Insert the installation CD into your computer’s CD-ROM or other compatible optical

drive.

2. Locate and open the \MAC directory. Locate the GeneUSBIDE.SIT file, and copy it to

the desktop. Once the file has been copied, double click on it to generate the driver

file automatically.

3. Copy the driver file produced in Step 2 to the extension directory (System Folder) -

(Extensions).

5. Connect the USB hard disk to the host computer. Once connected, restart the

computer, for software installation to conclude.

Using the added drive

Once the enclosure has been attached to a computer, and the necessary software has

been installed, the drive will be accessible as though it were installed within the system.

Prior to using the drive, it will need to be formatted according to your operating system

requirements. To format your newly attached hard drive, or create partitions, please

consult the documentation that accompanied your operating system at the time of

purchase.

Powering the added drive

The hard drive enclosure requires no external power supply, as it is capable of receiving

enough power (5V/500mA) from the USB Bus to which it is connected.

Instruction Manual

LED Indicator

The hard drive enclosure offers an LED indicator, to enable you to monitor drive activity.

When the enclosure is powered, the LED will illuminate and remain green. While the

hard drive is being accessed, however, the LED will change from green to red. Do not

remove the enclosure from the host computer while the LED is red, as it could damage

the drive or the enclosure, resulting in data loss.

Disconnecting the hard drive enclosure

Windows 98SE

The hard drive enclosure can be removed when the activity LED is green. To do so,

simply unplug the USB cable connecting the enclosure to the host computer.

Windows ME/2000/XP

1. Right click on the removable storage icon, located in the task bar.

Windows XP: When the Safely Remove Hardware message appears, click on it with

the left mouse button.

Windows ME/2000: When the Unplug or eject hardware message appears, click on

it with the left mouse button.

2. You will be asked to select the device you wish to disconnect. Please highlight the

drive listing, and click on OK.

Instruction Manual

Drive to be removed

3. On the screen that follows, click on Stop.

4. Wait for the message indicating that it is now safe to remove the device. Please note:

Removing the connected drive prior to receiving notification that it is safe to do

so, could result in losing or corrupting data stored on the drive. Once the Safe

to Remove Hardware message appears, please disconnect the enclosure from the

computer by removing the USB connection.

Mac

To safely disconnect the attached drive from the host computer, close any windows listing

the contents of the removable drive. Once all windows are closed, click on the USB

storage icon on the desktop, and drag it to the Trash Can icon on the desktop. Allow 5

seconds before physically removing the enclosure/drive from the computer.

TTrroouubblleesshhoooottiinngg

My computer does not recognize the hard drive or the enclosure.

1) Ensure that all necessary drivers have been installed. If you are using Windows

98SE, follow the driver installation instructions so that Windows can recognize a

removable hard drive. Also, ensure that the drivers for your USB controller have been

properly installed.

2) In the system BIOS, ensure that On-chip USB is enabled (if applicable).

Instruction Manual

SSppeecciiffiiccaattiioonnss

AAcccceessssoorryypprroodduuccttssffrroommSSttaarrTTeecchh..ccoomm

USB2HABM6

6 ft USB Cable for Canon, Sony, & Hewlett Packard Digital Camera

USB2HABM10

10 ft USB Cable for Canon, Sony, & Hewlett Packard Digital Camera

Instruction Manual

Hard Drive support IDE2510U2: 2.5” IDE (ATA 100)

SAT2510U2: 2.5” SATA / SATA II

Connectors USB mini B Female

Drive Capacity support 120GB, 5400 RPM

Maximum Data Transfer Rate 480Mb/s

Chipset Genesis GL-811E

Operating System support Windows 98SE/ME/2000/XP/Vista

Mac OS 9.X or Higher

Dimensions 120 x 75 x 10 mm (4.72 x 2.95 x 0.39”)

Weight 62.1g (2.19 oz.)

Regulatory Certifications FCC, CE, ROHS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Recinto de StarTech.com

StarTech.com

StarTech.com SAT2510U2REM Manual de usuario

StarTech.com

StarTech.com RK2537BKM Manual de usuario

StarTech.com

StarTech.com S2510BU33PW Manual de usuario

StarTech.com

StarTech.com SAT2510U2F Manual de usuario

StarTech.com

StarTech.com SAT35401U Manual del sistema

StarTech.com

StarTech.com SAT3510U3V Manual de usuario

StarTech.com

StarTech.com 8STS25SLOTR Manual de usuario

StarTech.com

StarTech.com SAT2510U2F Manual del sistema

StarTech.com

StarTech.com 2TBT3-PCIE-ENCLOSURE Manual de usuario

StarTech.com

StarTech.com INFOSAFE SAT2510BU2 Manual de usuario

StarTech.com

StarTech.com RK616WALM Manual de usuario

StarTech.com

StarTech.com IDECASE525F Manual de usuario

StarTech.com

StarTech.com S351BMU33ETG Manual de usuario

StarTech.com

StarTech.com SAT2520U2ER Manual de usuario

StarTech.com

StarTech.com SATBP125VP Manual de usuario

StarTech.com

StarTech.com SAT3550ESR Manual de usuario

StarTech.com

StarTech.com SAT2510U3REM Manual del sistema

StarTech.com

StarTech.com SAT35401U Manual de usuario

StarTech.com

StarTech.com M2-USB-C-NVME-SATA Manual de usuario

StarTech.com

StarTech.com S251BPU31C3 Manual de usuario

StarTech.com

StarTech.com UNI3510U2 Manual de usuario

StarTech.com

StarTech.com DRW110SAT Manual de usuario

StarTech.com

StarTech.com InfoSafe IDECASE35U2 Manual de usuario

StarTech.com

StarTech.com S352BMU3N Manual de usuario

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario