StarTech.com VS440HDMI Manual de usuario

Manual Revision: 02/06/2012

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

VS440HDMI

4x4HDMIMatrixVideoSwitchSplitterwithRS232

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Front View .................................................................................................................................................... 2

Rear View...................................................................................................................................................... 2

Installation ..............................................................................................3

Hardware Installation .............................................................................................................................. 3

Software Installation................................................................................................................................ 3

How to Use ..............................................................................................4

Front Panel................................................................................................................................................... 4

Software ....................................................................................................................................................... 5

Troubleshooting.....................................................................................7

Specications..........................................................................................8

Technical Support ..................................................................................9

Warranty Information............................................................................9

Instruction Manual

Introduction

The VS440HDMI 4x4 HDMI Matrix Video Switch Splitter with Audio and RS232 allows

you to share up to four distinct HDMI or DVI inputs (Using HDMI to DVI adapters - not

included) with audio between four independent displays or projectors.

Providing convenient front panel push-button and RS-232 PC control using the

included software, this Matrix switch allows each input and the corresponding audio to

be switched individually, meaning that dierent sources can be shown on each output

display or a single source can be output to several, oering maximum exibility.

This exible device features a front panel LCD for easy status monitoring, plus an

included remote control and IR extender module for simple control from a distance.

Designed to provide maximum control while saving space, the VS440HDMI can be

used as a standalone solution or rack-mounted using the included ear-mounts.

Backed by a StarTech.com 1 year warranty and free lifetime technical support.

Packaging Contents

• 1 x VS440HDMI video switch

• 1 x IR Extender Module

• 1 x Remote Control

• 2 x Rack Mounting Brackets

• 1 x DB9 RS232 cable

• 1 x Universal Power Adapter

• 1 x Software Installation CD

• 1 x Instruction Manual

System Requirements

• HDMI enabled video source device(s) (i.e. computer, game console, PVR/DVR, etc)

• HDMI enabled display device(s) (i.e. monitor, projector, HDTV, etc)

• Available AC power outlet

• Software: Microsoft®Windows®2000/XP/Vista/7 (32/64-bit), 32MB RAM,

10MB storage space, CD-ROM drive, RS232 serial port

Instruction Manual

Front View

Rear View

Instruction Manual

Installation

Hardware Installation

1. Make sure that all devices are powered o before beginning installation.

2. Connect the HDMI display device(s) to the HDMI Output connectors on the rear of

the matrix switch.

3. Connect the HDMI video source device(s) to the HDMI Input connectors on the rear

of the matrix switch.

4. OPTIONAL: If planning to use RS232 control for the matrix switch, connect a DB9

RS232 cable from the rear of the matrix switch, to the RS232 port on the host

computer system.

5. OPTIONAL: If using the IR Extender module, connect it into the rear of the matrix switch.

6. Connect the power adapter to the matrix switch, followed by powering on the

display devices, then the HDMI source devices.

7. The LCD screen on the front of the matrix switch should activate and display the

current status and Input-to-Output display relationships. The top row of the LCD

lists each output port, while the bottom row indicates which input port is being

displayed on it, with “0” representing no input selected (no video).

Software Installation

1. Insert the software installation CD into the computer’s CD/DVD drive.

2. On the CD, in the “AVM” folder, double click the AV Matrix le to start the installation.

3. Proceed through the installation prompts.

4. Once installation is complete, close the installation wizard. The software should

now be ready for use.

Instruction Manual

How to Use

Front Panel

OUT 1~4: Selects the numbered Output Port to be congured. An output must be

selected before selecting an input.

IN 1~4: Selects the numbered Input Port to map to an Output Port. Should only be

used after an Output Port has been selected rst, otherwise an error message will be

generated on the LCD status display.

ALL: Selects all of the Output ports at once. Used to congure all output ports

simultaneously with the same setting.

STO: Stores/saves the current Input/Output display relationships to internal memory.

EDID: Switches between“FIX” and “TV1” modes. FIX uses an internal EDID prole that

supports up to 1080p and sends it to each input device. TV1, uses the EDID from the

display connected to Output port 1 and sends it to each input device. Useful if the

connected display devices have dierent capabilities than the built in EDID that you

wish to use (i.e. dierent display resolutions).

OFF: Turns o the selected Output port. No video will be sent to the selected display(s).

RCL: Recalls/loads the stored display relationships from the“STO” button.

Instruction Manual

Software

Once the software is installed and the matrix switch is properly connected to the host

computer, launch the AV Matrix software to bring up the main control panel.

The panel on the left side will list all compatible matrix switches that are connected to

the host computer system. The name/model, number of ports will also be listed.

The center panel displays a grid showing the current Input-to-Output relationships for

the selected matrix switch. The numbered ports for Input and Output are listed along

the X and Y axis of the grid, with the currently set relationships highlighted.

The panel on the right side displays the stored display relationship proles for the

selected matrix switch. Up to 4 dierent custom proles can be saved for each matrix

switch from the software (front panel controls can only store 1).

The buttons along the bottom of the software window serve various functions:

Select/Deselect all output: Selects or deselects all 4 of the “Output” ports on the

matrix switch.

Disconnect all: Disables video output to all displays.

Scan: Refreshes the software window with any changes that may have been made

through directly using the front panel controls on the matrix switch while the software

is running.

Instruction Manual

Options: Used to congure the serial port on the computer, if necessary.

Selecting Video Output

Mapping the “Output” ports to an “Input” port can be accomplished through one of

two methods

Method 1:

1. Ensure the“Video”checkbox is checked in the bottom right corner of the center panel.

2. Click on the appropriate location on the grid to map the numbered “Output” port to

a numbered “Input” port.

Method 2:

1. Ensure the“Video”checkbox is checked in the bottom right corner of the center panel.

2. Click on the numbered “Output” port button(s) along the side of the grid.

3. Click on the numbered “Input” port button along the bottom of the grid that you

want the previously selected outputs to use.

4. Press the “Deselect all output” button in the bottom left corner of the window.

NOTE: If the I/O port relationships are changed from the front panel controls directly,

the software will need to be refreshed using the “Scan” button.

Disconnect/Disable Video Output

To stop video from being sent to one or more of the Output ports:

1.Press the numbered button for the Output port(s) from the side of the grid.

2.Press the “Disconnect” button in the bottom right corner of the grid.

3.Press the“Deselect all output” button in the bottom left corner of the software window.

Saving/Loading Stored Proles

The matrix switching software can store up to 4 dierent display relationship proles.

To save the current conguration, select the desired prole number from the drop

down list and press the“Save”button. To load the currently selected prole, click the

“Load” button.

Instruction Manual

Troubleshooting

If switching input/output with the front panel keys are not responsive.

• Press and hold the key for 2 seconds, then release, instead of just a quick press.

Loss of video output or color, or the unit becomes unusually hot.

• If the signal voltage dierence between the video source device(s) and the matrix

switch is too large, hot plugging could easily cause damage to the IC chips. Please

turn o power to the system before plugging or unplugging.

The LCD displays normally and the communication port has a return code but no

image is being output.

• The output/input cable connectors are loose. Simply reconnect the cables.

• The connection cable short-circuited. Simply replace the cable.

• The connection cable is broken. Simply replace the cable.

The front panel keys and communication ports are not responsive.

• Check that the equipment input power is properly connected and the computer

communication ports are working.

• Disconnect all cables and power and let sit for several minutes before attempting to

use again.

• Otherwise, contact technical support for further assistance.

Otros manuales para VS440HDMI

Tabla de contenidos

Otros manuales de Cables y conectores de StarTech.com

StarTech.com

StarTech.com ICUSBCPLLD25 Manual de usuario

StarTech.com

StarTech.com PCMACLINK2 Manual de usuario

StarTech.com

StarTech.com CRJ4550PK Manual de usuario

StarTech.com

StarTech.com ICUSBCPLLD25 Manual de usuario

StarTech.com

StarTech.com SATRD60CM Manual de usuario

StarTech.com

StarTech.com USB2SATAIDE Manual de usuario

StarTech.com

StarTech.com ICUSB232V2 Manual de usuario

StarTech.com

StarTech.com ST122PROA Manual de usuario

StarTech.com

StarTech.com ST124HDVW Manual de usuario

StarTech.com

StarTech.com ICUSB232FTN Manual del sistema

StarTech.com

StarTech.com ICUSBROLLOVR Manual de usuario

StarTech.com

StarTech.com USB3LINK Manual de usuario

StarTech.com

StarTech.com USB2SATAIDE Manual de usuario

StarTech.com

StarTech.com 1P3FPC-USB-SERIAL Manual de usuario

StarTech.com

StarTech.com ICUSB232V2 Manual de usuario

StarTech.com

StarTech.com ST222MX Manual

StarTech.com

StarTech.com SVID2USB2 Manual de usuario

StarTech.com

StarTech.com 35BAYPANEL Manual de usuario

StarTech.com

StarTech.com ICUSB232C2 Manual de usuario

StarTech.com

StarTech.com USB3S2SAT3CB Manual de usuario

StarTech.com

StarTech.com SVID2USB2NS Manual de usuario

StarTech.com

StarTech.com 35BAYPANELBK Manual de usuario

StarTech.com

StarTech.com SATRD30CM Manual de usuario

StarTech.com

StarTech.com 35BAYPANELBK Manual del sistema

Manuales populares de Cables y conectores de otras marcas

Philips

Philips SWA6310 Manual de usuario

Nohau

Nohau EMUL-IP2K-PC Manual de usuario

Foxun

Foxun SX-SP144E-HD4K2K Manual de usuario

Philips

Philips SWA3305W Manual de usuario

opticis

opticis Stretch DVIM1-1P0x Manual de usuario

Volkswagen

Volkswagen VAS 6558A Manual de usuario

NEXIBO

NEXIBO N-13 Manual de usuario

CYP

CYP PU-1H3HBTL Manual de usuario

Allen-Bradley

Allen-Bradley 1784-u2dhp Manual de usuario

Global Caché

Global Caché Flex Link Blaster Manual de usuario

Hauppauge

Hauppauge USB-Live2 Manual de usuario

Fenix

Fenix MPSV 15 Manual de usuario

BEGA

BEGA 71 085 Manual de usuario

Tesla

Tesla HPWC Manual de usuario

GAMERON

GAMERON LUXURY TV CABLE Manual de usuario

molex

molex Milli-Grid Dual row 87568 Series Manual de usuario

Burndy

Burndy Continental Industries thermOweld CRE-7 Manual de usuario

Chauvet DJ

Chauvet DJ Data Stream 8 Manual de usuario