StarTech.com WIF2HDMC Manual de usuario
Manual Revision: 06/04/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
WIF2HDMC / WIFI2HDMCGE
Wireless Display Adapter for Mobile Devices
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Product Diagram ....................................................................................1
Side View...................................................................................................................................................... 1
Back View ..................................................................................................................................................... 1
Introduction............................................................................................2
Packaging Contents ................................................................................................................................. 2
System Requirements.............................................................................................................................. 2
Installation ..............................................................................................3
Firmware....................................................................................................................................................... 4
Technical Support ..................................................................................16
Warranty Information............................................................................16
Instruction Manual
1
Product Diagram
Note: It is recommended the device WIFI2HDMC/WIFI2HDMCGE rmware be updated
to version 2.0.2. (Please see the Firmware section (Page 4) for details)
Mode Select Button
Power
adapter port
Side View
Back View
USB Media Input
Analog Audio/Video out
(For included 4 position A/V cable only)
HDMI-Out Port
RJ-45 LAN
Power
On/O
Instruction Manual
2
Introduction
Packaging Contents
• Wireless Display Adapter (WIFI2HDMC/WIFI2HDMCGE)
• Universal Power Adapter (NA/UK/EU)
• USB Cable to Power Adapter Port (optional for USB Power source)
• 4 position A/V cable
• Software Installation Disc
• Quick Installation Guide
System Requirements
• HDMI-enabled display device w/ cabling (i.e. television, projector)
• WiDi, Miracast, or 802.11n/g Wireless-enabled video source device (i.e. Smartphone,
tablet, Computer system)
• USB Flash Drive (For updating the device’s rmware)
Instruction Manual
3
Installation
1. Using an HDMI cable (not included), connect the HDMI-out port on the
WIFI2HDMC/WIFI2HDMCGE to the HDMI-in port on your HDMI-enabled display
device.
2. Using the included power adapter, connect the power adapter port on your
WIFI2HDMC/WIFI2HDMCGE to an available power outlet.
or
Using the included USB power cable, connect the power adapter port on your
WIFI2HDMC/WIFI2HDMCGE to an available USB power source.
3. Press the power button on the WIFI2HDMC/WIFI2HDMCGE to turn the device on.
Hardware installation is completed as the primary launch page is displayed on your
HDMI-enabled display device.
Notes:
• The primary launch page will take several seconds to display.
• The primary launch page may vary depending on your rmware version (See
Firmware section to update your rmware to the latest version).
Instruction Manual
4
Firmware
For optimal operation we recommend updating your rmware to the latest version
(2.0.2). There are three possible rmware versions that may be loaded on your
WIFI2HDMC/WIFI2HDMCGE (1.6.5 / 2.0.0 / 2.0.2). Please follow the below steps to
identify your current rmware version, and update your rmware if required.
Identify Your Current Firmware Version
1. Follow Hardware Installation to display the primary launch page on your HDMI-
enabled display device.
Note: The primary launch page may vary depending on your rmware version.
2. Identify and take note of your rmware version.
a) If your WIFI2HDMC/WIFI2HDMCGE has rmware versions 1.6.5 or 2.0.0 installed,
your rmware version will be displayed in the bottom right-hand corner.
b) If your WIFI2HDMC/WIFI2HDMCGE has rmware version 2.0.2 installed, your
rmware version will be displayed on the secondary launch page. (Press the mode
select button once on the WIFI2HDMC/WIFI2HDCMGE to switch to the secondary
launch page).
Instruction Manual
5
3. If your current rmware version is 1.6.5 or 2.0.0, please proceed to Update to the
Latest Firmware section in order to upgrade your rmware to the latest version. If
your current rmware version is 2.0.2, no rmware update is required.
Update to the Latest Firmware Version (2.0.2)
WARNING! Do not unplug the USB ash drive or power down the device until the new
primary launch screen is displayed.
Note: Firmware upgrades are irreversible
Once you have identied which rmware version is installed on your WIFI2HDMC/
WIFI2HDMCGE (See: Identify Your Current Firmware Version) follow the below
instructions to update your rmware based on your current version.
Instruction Manual
6
Update from Version 1.6.5
1. Download the rmware update les from StarTech.com.
2. Unzip the compressed le.
3. Copy install.img and install_sp.img from the downloaded folder to the root
directory (the parent/top directory) of the USB ash drive.
4. Ensure the WIFI2HDMC/WIFI2HDMCGE is powered o.
5. Plug the USB ash drive into the USB Media Input on the WIFI2HDMC.
6. Hold down the mode select button and turn on the WIFI2HDMC/WIFI2HDMCGE by
pressing the power button. Continue to hold down the mode select button while
the device powers on.
7. Release the mode select button after the “Please wait for USB update” appears on
your HDMI-enabled display device.
The rmware on your WIFI2HDMC/WIFI2HDMCGE will now update. Once the update
has completed the new primary launch page will be displayed:
Instruction Manual
7
Update from Version 2.0.0
1. Download the rmware update les from StarTech.com.
2. Unzip the compressed le.
3. Copy install_sp.img from the downloaded folder to the root directory
(the parent/top directory) of the USB ash drive.
4. Once the le has been moved to your USB ash drive, rename install_sp.img le
to install.img.
5. Ensure the WIFI2HDMC/WIFI2HDMCGE is powered o.
6. Plug the USB ash drive into the USB Media Input on the WIFI2HDMC.
7. Hold down the mode select button and turn on the WIFI2HDMC/WIFI2HDMCGE
by pressing the power button. Continue to hold down the mode select button
while the device powers on.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Adaptador de StarTech.com
StarTech.com
StarTech.com DKT3CHSD4GPD Manual de usuario
StarTech.com
StarTech.com ST2000PEXPSE Manual de usuario
StarTech.com
StarTech.com ICUSB422 Manual de usuario
StarTech.com
StarTech.com USB32HD4K Manual de usuario
StarTech.com
StarTech.com USB32HDDVII Manual de usuario
StarTech.com
StarTech.com 2CF2SATAR Manual de usuario
StarTech.com
StarTech.com TBT3TBTADAP Manual de usuario
StarTech.com
StarTech.com ESATAPLT2M Manual del sistema
StarTech.com
StarTech.com DKT30CHVCM Manual de usuario
StarTech.com
StarTech.com MHD2HDF11 Manual de usuario
StarTech.com
StarTech.com RJ45SPLITTER Manual de usuario
StarTech.com
StarTech.com ECUSB3S2 Manual de usuario
StarTech.com
StarTech.com 102B-USBC-MULTIPORT Manual de usuario
StarTech.com
StarTech.com CB2CFFCR Manual de usuario
StarTech.com
StarTech.com ICUBS232SM3 Manual de usuario
StarTech.com
StarTech.com DKT30CSDHPD3 Manual de usuario
StarTech.com
StarTech.com CDP2HD4K60SA Manual de usuario
StarTech.com
StarTech.com PEX10GSFP Manual de usuario
StarTech.com
StarTech.com USB3S2SATA Manual de usuario
StarTech.com
StarTech.com PCI150WN1X1 Manual de usuario
