Stardom Sohoraid SR4 Manual de usuario
SR4-WBS2
Four Drive RAID Storage Enclosure
2
8
16
24
32
38
44
»
SOHORAID SR4 Series User Manual
.......................................
»
SOHORAID SR4 Serie Bedienungsanleitung
.............................
»
Série SOHORAID SR4 Manuel de l’utilisateur
............................
»
Manual de usuario de SOHORAID SR4 Series
...........................
»
SOHORAID SR4 系列產品使用說明
.........................................
»
SOHORAID SR4シリーズユーザーマニュアル
..........................
»
SOHORAID SR4 시리즈 사용 설명서
........................................
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
About this manual
Thank you for purchasing STARDOM products.
This user manual will introduce the STARDOM SOHORAID SR4 product. Before using the
product, please read this manual thoroughly.
Although all information contained in this user manual has been carefully veried before
publishing, however, the actual product specication will be based on the time of delivery
from STARDOM. Any updates to the product specications or relevant information may be
found on www.stardom.com.tw. Products are subject to change without prior notications. If
you have any questions regarding the products of STARDOM, or you would like to know the
latest product information, user manual update, or rmware update, please contact your local
supplier or visit www.stardom.com.tw for further information.
Copyright © RAIDON TECHNOLOGY, INC. All rights reserved.
Table of Contents
1. Package Contents and Product Views
2. Environmental Requirements
3. Hardware Requirements and Precautions
4. Hardware Installation
5. Replacement of Malfunctioning Drive and Data Rebuild Instructions
6. System Temperature Overheat and Fan Failure Management
7. Visual Status Indicator Denitions
8. Introduction of the STARDOM Host Adapters
9. Frequently Asked Questions
2
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
1. Package Contents and Product Views
Open the package and you should nd the following:
SR4-WBS2 SR4-WBS2-4SX8
SR4-WBS2 x 1
(with removable drive tray enclosed x 4)
SR4-WBS2 x 1
(with removable drive tray enclosed x 4)
Power Cord x 1 Power Cord x 1
eSATA Cable x 1 eSATA Cable x 1
FireWire 800 (1394b) Cable x 1 FireWire 800 (1394b) Cable x 1
USB 2.0 Cable x 1 USB 2.0 Cable x 1
Accessory Kit x 4 Accessory Kit x 4
SR4-WBS2 User Manual x 1 SR4-WBS2 User Manual x 1
SJ20-x8 x 1
SJ20-x8 User Manual x 1
Please make sure that the contents listed above are not damaged or missing. If there are
damages or missing contents, please contact your supplier immediately.
Front and Rear Views
Alarm Mute
USB 2.0
e-SATA
FW800
FW800
2
A
C
B
D
1
6
10
11
12
12
4
8
3
7
5
9
13
14
1. Hard drive status indicator 2. Removable drive tray 3. Key access opening
4. Power indicator 5. Alarm indicator 6. Power switch
7. Power socket 8. Mute button 9. USB 2.0 interface connection
10. e-SATA interface connection 11. FireWire 800 (1394b) interface connection
12. Cooling fan 13. Anti-theft cord slot 14. Storage mode switch
3
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
Drive Position
A Drive position A B Drive position B C Drive position C D Drive position D
Storage Mode Denitions
・Safe mode (RAID 5) : Large volume storage with data protection.
・Speed mode (RAID 0) : Large volume storage with high speed throughput but without
data protection.
The secondary FireWire 800 (1394b) connection on the SR4-WBS2 is provided to connect
and extend to another FireWire 800 (1394b) device.
2. Environmental Requirements
Operating Temperature: 0 ~ 40°C (32 ~ 104°F)
Storage Temperature: -10 ~ 70°C (14 ~ 158°F)
Line Voltage:100 ~ 240V AC
3. Hardware Requirements and Precautions
1. Only one interface connection may be used at once per computer system.
2.
RAID volume formation utilizes the capacity of whichever hard drive has the smallest and
then multiply that capacity by three for RAID 5, four for RAID 0, to form a large volume,
therefore, it is recommended to only install hard drives of the same brand and specication
for all drive position prior to use. Moreover, when you need to replace with a new hard drive,
please be sure to purchase one with the same specication, capacity and brand. If these
conditions can’t be met, select one that’s at least 20 GB greater in capacity.
3. The actual storage capacity of SR4-WBS2 recognized by the system may differ from the
total capacity stated on the hard drives once the drives have been formatted.
4. When connected to the computer system, it’s prohibited to remove, insert or swap the
hard drive while data transfer is being performed.
5. It’s prohibited to change the positioning of the drives once the initial installation has been
completed as the changes made to the drive positions may destroy the RAID formation.
6. If you discover that hard drive failure is taking place, go to Section 5 “Replacement of
Malfunctioning Drive and Data Rebuild Instructions” and follow the steps accordingly.
7.
Whenever turning off or unplugging the SR4-WBS2 from your computer system becomes
necessary, always remember to safely remove it from your operating system rst.
8. In RAID 5 mode, the system allows one single hard drive failure. If multiple drive failures
occur at once, it’s likely that all data stored in the system have been destroyed or lost. In
RAID 0 mode, if one hard drive failure occurs, then all data maybe destroyed or lost. If
this happens, we recommend you to consult with a professional hard drive data recovery
specialist to see if your data may be recoverable.
4
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
9. It is highly recommended for users to back up important data contained within the SR4-
WBS2 unit on a regular basis or whenever the user feels necessary to a remote or a
separate storage device. Stardom will not be responsible for any lost of data caused
during the use of the unit or the recovery of the data lost.
4. Hardware Installation
Please follow the instructions below to complete the hardware installation:
Step 1
Open the package and take out the product making sure that all the enclosed contents
are not damaged or missing. If there are damages or missing contents, please contact
your supplier immediately.
Step 2
Place the device on a stable surface, ensure that it is well ventilated without blockage
to the vent and kept away from locations near moisture or where the product may
become vulnerable resulting in damages.
Step 3 Choose the storage mode of your choice through the storage mode switch located
at the rear of the unit.
Step 4
Use the provided key in the accessory kit and insert it into the key access opening
to eject the removable drive tray latch and extract the removable drive tray.
Step 5 Remove the drive stabilizer from the removable tray. Mount the hard drive onto the
tray and secure it with the screws provided in the accessory kit. Once completed,
insert the drive tray back to the drive position A and push the latch into place.
Repeat the same procedure for drive position B, C, and D in sequence to complete
all drive installations.
Step 6 Choose the corresponding cable to connect the preferred interface connection on
the back of the SR4-WBS2 to the computer.
5
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
Step 7 Connect one end of the AC power cord to the SR4-WBS2’s power socket and the
other end to a wall socket. Then power on the unit.
Step 8
Wait for the system to complete initialization as the hard drive status indicator will
briey light up in red and blue interchangeably and then stop. When your computer
has booted, your operating system should recognize the RAID volume automatically.
After the volume has been successfully recognized, please follow the formatting of
hard drive instructions given by the operating system to format the drive volume of
your preference. Once the formatting has been completed, the RAID system is
ready for use.
5. Replacement of Malfunctioning Drive and Data Rebuild Instructions
When a front hard drive indicator has lit up red and the audio alarm sounds, this could mean
the indicated hard drive may be malfunctioning. If this occurs, you may press the mute button
at the rear of the system to shut off the audio alarm and power off the system immediately if
in the allowed operational state, and then re-power on the system to double check and see if
in fact the indicated hard drive has malfunctioned. If the problem persists, please turn off the
system and follow the directions below :
Step
1 Remove the drive tray containing the malfunctioned hard drive and disassemble
the hard drive from drive tray.
Step
2
Mount the new hard drive onto the tray and insert it back to the empty drive position
of the SR4-WBS2, then push the latch into place making sure it is secured and locked.
Step
3 In RAID 5 mode, when you turn the system on, the hard drive status indicator of the
replacement drive will interchangeably blink red and purple to inform that the data is
being rebuilt to the replacement drive. During data rebuild, you may operate the SR4-
WBS2 as normal. When the indicator stops, the data rebuild process has been
completed.
In RAID 0 mode, since all data have been destroyed or lost due to hard drive malfuntion,
you are required to re-format the drives for use.
6. System Temperature Overheat and Fan Failure Management
If the alarm indicator has lit up red and the audio alarm sounds, this could mean that either a
system fan has stopped operating entirely or the system temperature has exceeded over the
default temperature of 60°C. When this occurs, you may press the mute button at the rear of
the system to shut off the audio alarm and power off the system immediately if in the allowed
operational state to let the system cool. Check and see if the overall operation environment is
well ventilated and make sure there are no blockages to the enclosed fan and then re-power
on the system to continue use. If the problem persists, please turn off the system and contact
your supplier or the STARDOM tech support for further assistance.
6
SOHORAID SR4 Series User Manual
English
Deutsch
Français
Español
中文
日本語
한국어
7. Visual Status Indicator Denitions
Hard drive status indicator :
1. The front hard drive status indicator lights up in blue, the hard drive is on standby.
2.
The front hard drive status indicator lights up in red, the hard drive is missing or
malfunctioning.
3. The front hard drive status indicator blinks in blue, the hard drive is reading/writing data.
4. The front hard drive status indicator blinks in purple, data rebuild is in progress.
5. The front hard drive status indicator of newly installed hard drive blinks in red and purple
interchangeably, data rebuild is in progress.
6.
The front hard drive status indicator blinks in red and blue, system initialization is processing.
Power indicator:
1. When the power indicator lights in blue, this means the power of the system is on.
2. When the power indicator is off, this means the power of the system is off.
Alarm indicator:
1.
The alarm indicator will light up in red if the system temperature exceeds the safety limitation,
the cooling fan fails or the hard drive has not been installed or has failed.
2. When the alarm indicator is off, the system temperature, cooling fan and hard drives are
in the normal state.
8. Introduction of the STARDOM Host Adapters
If you require an host adapter to be used with this system, please log onto www.stardom.
com.tw to nd the recommeded adapter or contact STARDOM for more information.
9. Frequently Asked Questions
Q1. Which drive format should I choose to format the hard drives in the SR4-WBS2?
A : It depends on the computer system you most often use. See the below suggestions:
1. Use NTFS for Windows 2000/XP/Vista/Windows 7 system.
2. Use HFS+ (Mac OS Extended) format for a Mac OS X system.
3. Choose FAT32 format if you’ll use the SR4-WBS2 in both Windows and Mac
environments (the maximum size of one single le may not exceed 4 GB).
Q2. Why can’t my SR4-WBS2 reach the high transfer performance speed beyond 200 MB/
sec. via e-SATA interface as stated on your website?
A : 1. Please rst check if your PCI-E SATA host adapter would only support PCI-E (1X).
This type of host adapters cannot reach the transfer performance speed beyond 140
MB/s.
2.
It is recommended to purchase STARDOM SJ20-8x (PCI-E 8X) host adapter to enhance
the transfer speed performance via e-SATA.
7
SOHORAID SR4 Serie Bedienungsanleitung
English
Deutsch
Français
Español
中文
日本語
한국어
Über diese Anleitung
Vielen Dank für den Kauf eines STARDOM Produkts.
Dieses Bedienungsanleitung beschreibt das STARDOM SOHORAID SR4 Produkt. Bevor Sie
dieses Produkt benutzen, lesen Sie diese Anleitung bitte sorgfältig durch.
Obwohl alle Informationen in dieser Anleitung vor der Veröffentlichung sorgfältig überprüft
wurden, beziehen sich die tatsächlichen Produktspezikationen auf die Zeit der Auslieferung
durch STARDOM. Aktualisierungen der Produktspezikationen können auf der Webseite
www.stardom.com.tw gefunden werden. Änderungen der Produkte ohne vorherige
Nachricht
vorbehalten. Wenn Sie Fragen zu den Produkten von STARDOM haben, oder mehr
über die aktuellsten Produktinformationen, Aktualisierungen der Bedienungsanleitung oder
Firmwareupdates erfahren möchten,
kontaktieren Sie bitte Ihren Händler vor Ort oder besuchen
Sie www.stardom.com.tw für weitere Informationen.
Copyright © RAIDON TECHNOLOGY, INC. All Rechte vorbehalten.
Inhaltsverzeichnis
1. Packungsinhalt und Produktansichten
2. Betriebsbedingungen
3. Hardwarevoraussetzungen und Vorsichtsmaßnahmen
4. Hardwareinstallation
5. Austausch eines defekten Laufwerks und Anweisungen zur Datenwiederherstellung
6. Verhalten bei Systemüberhitzung und Lüfterausfall
7. Beschreibung der visuellen Statusanzeige
8. Beschreibung des STARDOM Host Adapters
9. Oft gestellte Fragen
8
SOHORAID SR4 Serie Bedienungsanleitung
English
Deutsch
Français
Español
中文
日本語
한국어
1. Packungsinhalt und Produktansichten
Öffnen Sie das Paket und Sie sollten die folgenden Dinge vornden:
SR4-WBS2 SR4-WBS2-4SX8
SR4-WBS2 x 1
(mit integriertem Wechselrahmen x 4)
SR4-WBS2 x 1
(mit integriertem Wechselrahmen x 4)
Stromkabel x 1 Stromkabel x 1
eSATA Kabel x 1 eSATA Kabel x 1
FireWire 800 (1394b) Kabel x 1 FireWire 800 (1394b) Kabel x 1
USB 2.0 Kabel x 1 USB 2.0 Kabel x 1
Zubehörset x 4 Zubehörset x 4
SR4-WBS2 Bedienungsanleitung x 1 SR4-WBS2 Bedienungsanleitung x 1
SJ20-x8 x 1
SJ20-x8 Bedienungsanleitung x 1
Bitte stellen Sie sicher, dass die oben aufgelisteten Inhalte nicht beschädigt sind oder
fehlen. Falls Schäden oder fehlende Inhalte festgestellt werden, kontaktieren Sie bitte
umgehend Ihren Händler.
Vorder- und Rückansichten
Alarm Mute
USB 2.0
e-SATA
FW800
FW800
2
A
C
B
D
1
6
10
11
12
12
4
8
3
7
5
9
13
14
1. Festplatten-Statusanzeige 2. Wechselrahmen 3. Schlüsselzugangsöffnung
4. Netzanzeige 5. Alarmanzeige 6. Netzschalter
7. Netzbuchse 8. Stummtaste 9. USB 2.0 Anschluss
10. e-SATA Anschluss 11. FireWire 800 (1394b) Anschlüsse
12. Kühllüfter 13. Steckplatz für Kensingtonschloss
14. Speichermodus Schalter
9
Otros manuales para Sohoraid SR4
1
Tabla de contenidos
Idiomas:
Otros manuales de Almacenamiento de Stardom
Stardom
Stardom SOHORAID MR2-B31 Manual de usuario
Stardom
Stardom SR2-B31 Manual de usuario
Stardom
Stardom SOHORAID MR2-B31BP Series Manual de usuario
Stardom
Stardom MR2-WBS2 Manual de usuario
Stardom
Stardom SA2TB3 Manual de usuario
Stardom
Stardom SOHORAID SR8-TB3 Manual de usuario
Stardom
Stardom SOHORAID SR3MSB-B31 Manual de usuario
Stardom
Stardom SOHORAID SR4-TB3 Manual de usuario
Stardom
Stardom SOHORAID DR8-TB2 Manual de usuario
Stardom
Stardom SafeTANK GT5640-B31 Manual de usuario
Stardom
Stardom sohoraid ST2-B31 Manual de usuario
Stardom
Stardom SOHORAID DR5-WBS3 Manual de usuario
Stardom
Stardom DR2-B31 Manual de usuario
Stardom
Stardom iTANK MT1-B31BP Manual de usuario
Stardom
Stardom SR2611 Series Manual de usuario
Stardom
Stardom SOHORAID DR2-TB2 Manual de usuario
Stardom
Stardom SOHOTANK MS2-TB3 Manual de usuario
Stardom
Stardom ST4-B31 Manual de usuario
Stardom
Stardom sohoraid ST2-B31 Manual de usuario
Stardom
Stardom SA2TB2 Manual de usuario
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario