Star Trac E Series Manual de referencia

Customer Services Bulletin

STAR TRAC FITNESS

1 of 3

637-4229 Rev: A

Display Not Powering Up at Install

E Series E-CT, Bikes, and Steppers

After an E-Series CT, Bike or Stepper has been fully assembled it is required to “initialize” the display electronics in order

to ensure the LED’s will illuminate or “wake up” every time.

Tools Required:

Philips Screwdriver

Getting The Unit to Wake Up:

The unit must be self powered to start this process. If the unit has PVS, make sure the power adapter is unplugged.

Start pedaling (Bike) striding (CT) or Stepping (Stepper) on

the unit for 5 seconds to see if the unit powers up. If unit

does not power up stop pedaling, striding, or stepping for a

minimum of 45 seconds and repeat this step.

If the unit does not wake up the second time, use a

Philips screwdriver to open the display of electronics.

Unplug the data cable from the display found in the

lower left corner for 5 seconds, then reseat the

connector.

Start pedaling (Bike) striding (CT) or Stepping on the unit for 5 seconds to see if the unit powers up. If unit does not power

up repeat the previous step. Once the display does wake up proceed to the next step.

Initialize the Display:

For video instructions on the following

steps, please click

http://www.youtube.com/watch?v=5VkjXD

zI5hc&feature=youtu.be or follow the

diagram steps.

Customer Services Bulletin

STAR TRAC FITNESS

2 of 3

637-4229 Rev: A

Once the unit is awake, press the number “0”, “2”, and

“Start” at the same time to get into the maintenance mode.

Right when “Maintenance Mode” comes up, press the

numbers “1”, 4” and 7” at the same time. “Init Variables” will

appear.

Note: very important to do it within 3 seconds of seeing the

“maintenance mode”

“Please Wait” will then appear.

Let the unit power down.

Start pedaling.

Return to the “Maintenance Mode”. Using the “SCROLL”

key. If it is plugged in the wall, make sure the “Wall Power”

is on.

Customer Services Bulletin

STAR TRAC FITNESS

3 of 3

637-4229 Rev: A

To change the values from “On” to “Off”, press the + or –

button.

Serial number should be 00000. Then press “SCROLL”

Change weight to 155

Change time to 99

Change model to Bike

Make sure CSAFE is off.

Press “OK” to save all setting.

Otros manuales para E Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Entrenador elíptico de Star Trac

Star Trac

Star Trac S-TBTx Manual de usuario

Star Trac

Star Trac 8-RB Manual de usuario

Star Trac

Star Trac Core Health & Fitness 8-RDE Manual de usuario

Star Trac

Star Trac StairMaster 8-CT Manual de usuario

Star Trac

Star Trac Elliptical Edge Manual de usuario

Star Trac

Star Trac Pro Manual de usuario

Star Trac

Star Trac Elliptical Edge Manual de usuario

Star Trac

Star Trac Pro CrossTrainer Elite CrossTrainer Manual de usuario

Star Trac

Star Trac StairMaster 8-CT Manual de usuario

Star Trac

Star Trac E-TBTe Manual de usuario

Manuales populares de Entrenador elíptico de otras marcas

Weslo

Weslo Momentum 4.0 Elliptical Manual de operación y mantenimiento

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manual de usuario

Torque Fitness

Torque Fitness XPLLP Manual de usuario

Octane Fitness

Octane Fitness PRO3700C Manual de usuario

Xterra

Xterra FS5.8e Manual de usuario

Bodyguard

Bodyguard E-40 Manual de usuario

Bonn Germany

Bonn Germany Concept 2.2 Manual de usuario

Precor

Precor Resolute RSL 620 Manual de usuario

NordicTrack

NordicTrack E 9.2 Elliptical Manual de usuario

Vision Fitness

Vision Fitness X6600iNetTV Manual de usuario

Matrix

Matrix MX-A5x Manual de usuario

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manual de usuario

Sears

Sears FREE SPIRIT C249 30737 0 Manual de usuario

True

True FS-64 Manual de usuario

Sport-thieme

Sport-thieme ST 310 Manual de usuario

VIRTUFIT

VIRTUFIT CTR 1.1 Manual de usuario

Kettler

Kettler GIRO C 1 Manual de usuario

CIRCLE FITNESS

CIRCLE FITNESS E7 Manual de usuario