07
13. THIRD LIMIT SWITCH (PREFERRED POSITION)
13.1 USING REMOTE CONTROL Item 596
13.3 USING COMMAND BUTTONS
In the case of blinds with ADJUSTABLE slats, it is possible to decide whether to associate the THIRD LIMIT SWITCH to the fully lowered blind position with open slats or to the
lowered blind position with closed slats. In any case, it is better to initially associate the THIRD LIMIT SWITCH to the completely lowered position with slats closed, since the
LOWER limit switch has already been stored and associated with the completely lowered blind position with open slats. Subsequently, it is possible to invert the LOWER LIMIT
SWITCH with the THIRD LIMIT SWITCH at will and at any time (see paragraph 14).
13.2 USING REMOTE CONTROL Item 595
To store the THIRD LIMIT SWITCH:
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG* on the back. The motor performs an up/down
movement.
03. Press DOWN twice. The motor performs an up/down movement.
04. Press STOP. The motor moves to the lower limit switch.
04. Move the motor to the desired position (with ADJUSTABLE
slats, close blind and slats completely).
05. Press PROG 3 times to exit.
To call up:
01. Briefly press STOP 3 times
14. THIRD LIMIT SWITCH INVERSION
14.1 USING REMOTE CONTROL Item 596
01. Bring the motor to the intermediate position
02. Briefly press MENU on the back. The motor performs an up/down movement.
Display shows: - - . Press 3 times on DOWN. 03 appears on the display.
03. Press STOP. The motor moves to the lower limit switch position.
04. Press UP once. The lower limit switch has been reversed with the third limit switch.
05. The motor signals UP.
06. Press MENU to exit.
14.3 USING COMMAND BUTTONS
14.2 USING REMOTE CONTROL Item 595
01. Bring the motor to the intermediate position
02. Press 3 times on PROG* on the back. The motor performs an up/down movement.
03. Press DOWN 3 times. The motor performs an up/down movement
04. Press STOP. The motor moves to the lower limit switch position.
05. Press UP once. The lower limit switch has been reversed with the third limit switch.
06. The motor signals UP.
07. Press PROG 3 times to exit.
Wait for 5
seconds
12
39
6
2 x DOWN
ON
3 x DOWN
3 x UP
To store:
01. Bring the motor to the intermediate position.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press UP 3 times and DOWN 3 times*.
The motor completes 1 up/down movement.
04. Within 15 seconds, briefly and quickly press DOWN twice.
The motor shows: up/down.
05. Press the buttons bringing the motor to the desired position.
06. Wait for 5 seconds. The motor exits the menu without any movement.
To call up:
01. Quickly press DOWN 3 times.
01. Bring motor to the lower limit switch.
02. Turn off the power, wait a few seconds, then power up again.
03. Within 15 seconds, briefly and quickly press UP 3 times and DOWN 3 times*.
The motor moves up/down.
04. Within 15 seconds, briefly and quickly press DOWN 3 times.
The motor moves to the lower limit switch position.
05. Briefly press UP to invert the third limit switch.
06. The motor signals UP.
07. Wait for 5 seconds. The motor exits the menu without any movement.
15. SUN AND WIND ANEMOMETERS
The sun/wind sensors generate automatic operations without warning, which can be a source of danger. The installer is responsible for informing the end user and possibly integrating
appropriate safety systems to the installation. In some situations, (e.g., loss of motor or sensor voltage, motor or sensor failure, radio disturbances, etc.), it is possible that the
command given by the sensor may not be detected by the motor. The sensor must therefore not be understood as a safety device designed to guarantee the integrity of the rolling
shutter under all conditions, but a means to reduce the probability that the rolling shutter will be damaged by adverse weather events.
(*) The buttons must be pressed shortly, max 1 second between two pressures.
(*) The buttons must be pressed shortly, max 1 second between two pressures.
16. SUN/WIND ANEMOMETER RADIO TEST
As soon as a sun/wind radio anemometer is stored in the motor, a communication check is automatically activated between radio anemometer and motor. Communication between
the two devices occurs every 15 seconds. If communication fails twice consecutively, the motor performs an ascent manoeuvre to protect the rolling shutter. The automatic protection
manoeuvre is performed only once, remaining in place until radio communication is restored. It is possible to “query” the motor on the alarm status. Please refer to the anemometer
manual.
15.1 ANEMOMETERS COMPATIBLE WITH RX-E3 MOTORS
The V6.RX-E3 and V7.RX-E3 motors feature an integrated radio receiver and require the use of radio anemometers. Use model 595.K.XS.00 (sun/wind sensor for one or more
motors). The sensor constantly communicates to the associated motors wind intensity and brightness. Each motor, depending on the thresholds set inside it, decides whether to
trigger the wind or the sun alarm. In the event of wind alarm, the motor engages the upward mode, also inhibiting the manual commands until the end of the alarm. In the event of sun
alarm, the tuned motors activate a descent mode. When the sensor detects the absence of sun, the message “no sun” is sent to the motors. In turn, the motors activate the ascent
mode. For more information, refer to the relevant anemometer manual.
Wait for 5
seconds
12
39
6
3 x DOWN
ON
3 x DOWN
3 x UP
1 x UP
Sun function activation with remote control Item 596
Press the SUN button on the remote control until the
state of the YELLOW LED varies (about 2 seconds).
The motor moves up/down to confirm the change.
Select the channel associated with the motor
(except “SE” Sequencer)
YELLOW LED LIGHT ON/OFF:
“sun” function active/off
For clarification, refer to the manual of your sun-wind sensor.
Sun function activation with remote control Item 595
For clarification, refer to the manual of your sun-wind sensor.
01. Bring the motor to the intermediate position.
02. Press 3 times on PROG on the back. The motor shows:
up/down.
03. Press UP twice and DOWN twice, then press STOP.
04. The motor shows: up/down.
05. To activate, press UP once.
To deactivate, press DOWN once.
06. After 2 seconds, the motor replicates the movement.
07. Press PROG 3 times to exit (the motor does not show
anything).
To store the THIRD LIMIT SWITCH:
01. Bring the motor to the intermediate position.
02. Briefly press MENU on the back. The motor performs an up/down Display
shows: - - . Press DOWN twice. 02 appears on the display.
04. Press STOP. The motor moves to the lower limit switch.
04. Move the motor to the desired position (with ADJUSTABLE
slats, close blind and slats completely).
05. Press PROG to store settings. The motor performs an up/down movement.
06. Press MENU to exit.
To call up:
01. Press the THIRD LIMIT SWITCH button on the remote control.
In the case of blinds with ADJUSTABLE slats, it is possible to decide whether to associate the THIRD LIMIT SWITCH to the fully lowered blind position with open slats or to the lowered
blind position with closed slats. In any case, it is better to initially associate the THIRD LIMIT SWITCH to the completely lowered position with slats closed, since the LOWER limit switch
has already been stored and associated with the completely lowered blind position with open slats.
If you try to invert the THIRD LIMIT SWITCH before storing its settings, an error is signalled by 4 movements of the motor. It is possible to invert the LOWER LIMIT SWITCH with the
THIRD LIMIT SWITCH at any time, proceeding as follows:
