Stabila 196 electronic IP65 Manual de usuario
Operating Instructions196 electronic IP65
196 M electronic IP65
EN
196 / 196 M electronic IP65
1
en
The STABILA 196 electronic IP65 is an electronic spirit level
with 2 digital displays for quickly and easily measuring
inclinations and angles.
If you still have any questions aer reading the
operating instructions, feel free to call our hotline:
0049 / 63 46 / 3 09 - 0
Equipment and functions:
• vertical vial(s) for vertical levelling, in reverse position too
• horizontal vial for horizontal levelling, in reverse position too
• electronic module with 2 digital displays for accurately
determining inclinations and angles
Operating Instructions
196 / 196 M electronic IP65
2
en
Components of the unit
Buttons:
On/Off
Operating mode selection
Reference
Measurement memory
Lighting
Acoustic signal
Calibration
Button lock
1. 2 Displays
2. Battery compartment lid
3. Magnet (196 M electronic IP65)
4. Vials - vertical and horizontal
5. Removable, shock-absorbing end caps
6. Anti-slip stopper
7. Electronic module
- dust-proof and waterproof in accordance with IP 65
IP 65
IP 65
196 / 196 M electronic IP65
3
en
2x 1.5V
alkaline
AA, LR6, Mignon
MN 1500
Unscrew battery compartment lid on rear, insert new
batteries according to symbol in battery compartment.
Suitable rechargeable batteries can also be used.
LCD:
low battery charge - insert new battery
Dispose of used batteries at suitable collection
points - not with household waste.
Do not leave in unit!
Remove the batteries if you do not intend
to use the unit for some time!
Insert batteries / Battery replacement
196 / 196 M electronic IP65
4
en
After switching on, an automatic self-test is carried out.
All the display's segments are shown.
After the end of the test, the version number S x.xx of the
measurement program is briefly displayed and the saved
automatic switch-off time of 1/8 or 2 hours displayed.
An acoustic signal indicates that the unit is ready for
operation.
The display shows the angle measured in the set unit
of measurement.
Commissioning
test
off
Software Version
196 / 196 M electronic IP65
5
en
Automatic display inversion
The two displays are inverted for overhead measurements
so they are always legible.
Alignment guides
Arrows in the display show which way to turn the
spirit level to the horizontal (-15°/0 °/+ 15°) or
vertical (+75°/90°/-75°).
The acoustic alignment guide is activated /
deactivated using the "Acoustic signal" button.
If the acoustic signal is activated, the tone
sequence speeds up as the 0° or 90° position is
approached in a range of ± 2° to the horizontal
or vertical. A change in the pitch indicates that
these positions have been exceeded.
A continuous tone confirms the precise point
at which the horizontal / vertical is reached.
This is also indicated on the display with 2
"centre display" bars.
The electronic spirit level can also be aligned using the vial.
196 / 196 M electronic IP65
6
en
0,05˚
0,1˚
The unit of measurement is set by pressing
the MODE button several times.
° Rough: Display in 0.1° steps
° Fine: Display in 0.05° steps
%: Display in 0.1 % steps
mm/m: Display in 1 mm/m steps
in/ft decimal: Display in 0.01 in/ft steps
in/ft fraction: Display in 1/8 in/ft steps
The set unit of measurement is retained after the unit is
switched off.
Setting the unit of measurement
MODE
196 / 196 M electronic IP65
7
en
The REF button can be used to select any set angle as
0° reference. The angle details now displayed relate to
this reference angle. The display flashes in this setting.
The original reference angle value is displayed for 2 seconds
by briefly pressing the REF button.
The reference angle is deleted by:
• Pressing and holding (≥ 3 sec) the REF button
If the button lock is active, this must be disabled first.
• Switching off
• The automatic switch-off function
The zero position again refers to the calibrated setting.
The alignment selected for the electronic spirit level must
not be changed during the reference function!
Reference angle
- freely selectable zero position
+5°
(= 25° )
0°
(= 20° )
20°
( + 5° )
RESET
REFERENCE
REFERENCE
20°
3 sec
1x
1x
1x
3 sec
2 sec
196 / 196 M electronic IP65
8
en
Briefly pressing the "Lighting" button switches the display
lighting on for approx. 60 seconds.
Pressing and holding the "Lighting" button switches the
lighting permanently on or off.
The pressing of this button is confirmed by an acoustic signal.
Lighting
1x
1x
1x
on = 60 sec
on = ∞
Button lock
Pressing and holding ( ≥ 3 sec ) the "Key" button locks the
Operating mode selection
Reference
Measurement memory
Calibration
buttons. The button lock remains active after switching the
unit off and back on again!
Pressing and holding the "Key" button disables the button
lock. The pressing of this button is confirmed by an acoustic
signal.
1x
1x
5 sec
196 / 196 M electronic IP65
9
en
1x
1x
HOLD
Measurement memory
The current measurement can be saved by pressing the
HOLD button. The arrows and the "centre display" bars
flash. The measurement is displayed continuously.
Close to 0° and 90° the arrows flash to indicate direction.
The saved measurement is deleted by again pressing the
HOLD button or switching the unit off.
Tabla de contenidos
Otros manuales de Nivel láser de Stabila
Stabila
Stabila TECH 196-2 Electronic Series Manual de usuario
Stabila
Stabila LAX 300 G Manual de usuario
Stabila
Stabila Laser LA-P+L Manual de usuario
Stabila
Stabila Laser LAX 300 Manual de usuario
Stabila
Stabila Laser LAR 120 G Manual de usuario
Stabila
Stabila Laser FLS 90 Manual de usuario
Stabila
Stabila LAPR-150 Manual de usuario
Stabila
Stabila LA-5P Manual de usuario
Stabila
Stabila LA 90L Manual de usuario
Stabila
Stabila LAR-250 Manual de usuario
