ST STEVAL-BCN002V1B Manual de usuario

Quick Start Guide

STEVAL-BCN002V1B - BlueTile kit

www.st.com/bluetile

What do you want to do? 2

Unpack and run

the default demo Start designing

your application

Go to page 8 Go to page 10

www.st.com/bluetile ST BLE Sensor

Run the preloaded Demo

•The preloaded demo on Bluetile is the BLE_SensorDemo available in the SDK software development kit

3

Step 1

To power the system, slide

the battery inside the holder.

Step 2

Download and run the ST BLE Sensor

app from the iOS or Android store

www.st.com/bluems

Step 3

Discover, connect and see the

data in real time; swipe for more

ST BLE Sensor

Run the preloaded Demo 4

Environmental

sensors Inertial sensor and

MotionFX fusion Accelerometer

events LED control Voice over BLE

(BlueVoice)

References for libraries embedded in the demo

•UM2220 Getting started with MotionFX sensor fusion library

•UM2382 / UM2196 Getting started with BlueVoice full/single duplex

www.st.com/bluetile ST BLE Sensor

Start designing your application 5

Software setup

SDK & IDE Hardware setup

Flash & Debug

Go to page 11 Go to page 12

Flash only

using the host board Flash & Debug

using the host board

and ST-Link on a Nucleo

Software setup: SDK & IDE

•Download and unzip the Bluetile SDK (software development kit) from www.st.com/bluetile

6

BLE_SensorDemo is the default

firmware preloaded for demo purposes

Select the most appropriate project in BLE_Examples directory

•BLE_Beacon to advertise programmable data

•BLE_HID_Peripheral to emulate a wireless keyboard or mouse

•BLE_SensorDemo to stream sensor data to the reference app ST BLE Sensor

•DTM to enable BlueNRG-2 control in real-time using STSW-BNRGUI software tool

Open the project file corresponding to your favorite IDE

•EWARM for IAR Embedded Workbench by IAR

•MDK-ARM for KEIL uVision by ARM

•TrueStudio for TrueStudio by Atollic

Step 1

Step 2

Step 3

Hardware setup: Flash & Debug 7

Step 1

Remove the battery and plug the BlueNRG-Tile on its

host board, move switch SW2 and SW3 in position 2-3 Remove the battery and plug the BlueNRG-Tile on its

host board, plug the host board on any Nucleo ST-Link

Flash Flash & Debug with supported IDEs

10 pin SWD/UART connector 5 pin SWD connector

Alignment connectors

SW2 and SW3

in position 2-3

Remove

the battery

not needed for

Window 10

Hardware setup: Flash & Debug 8

Step 3

Step 1

Step 2

Connect the USB of the host board to the laptop

Download and install STSW-STM32102

Virtual COM port driver (VCOM)

Download, install, run STSW-BNRGFLASHER

to Flash BlueNRG-2(reference manual UM2406) Download, install and run STSW-BNRG1STLINK

to Flash BlueNRG-2 (reference manual UM2109)

Connect the USB of the host board to the laptop, also

connect the USB of the Nucleo ST-Link to the laptop

Flash Flash & Debug with supported IDEs

Flasher

in UART

mode

SW2 and SW3 in position 2-3

Host board

If BlueNRG-2 is in deep sleep, it is not possible to Flash & Debug

(use STSW-BNRGFLASHER to Flash - see next slide)

Flash & Debug using supported IDEs (IAR, Keil, Atollic

TrueSTUDIO) or…

Hardware setup: Flash & Debug

•If BlueNRG-2 is in deep sleep

•It is not possible to Flash & Debug with STSW-BNRG1STLINK: the SWD interface is shut down and the ST-Link will not

detect BlueNRG-2

•Use STSW-BNRGFLASHER to Flash then Debug with supported IDEs

•Use STSW-BNRGFLASHER to mass erase then Flash & Debug with supported IDEs

•When debugging, custom firmware should not enter deep sleep: as soon as the deep sleep mode is activated the SWD

interface will be shut down and the ST-Link will be disconnected

•When the BlueNRG-Tile is plugged on its host motherboard, the reference firmware automatically disables deep sleep

mode to enable Flash & Debug with the ST-Link

•BlueNRG-2 is not an STM32 microcontroller!

•The standard ST-Link Utility STSW-LINK004 will NOT work with BlueNRG-2

•Use the BlueNRG ST-Link Utility STSW-BNGR1STLINK or STSW-BNRGFLASHER

9

More information

10

Otros manuales para STEVAL-BCN002V1B

1

Tabla de contenidos

Otros manuales de Hardware de computadora de ST

ST

ST EVALSPEAr320HMI Manual de usuario

ST

ST FP-LIT-BLEMESH1 Manual de usuario

ST

ST X-NUCLEO-OUT14A1 Manual de usuario

ST

ST UM2727 Manual de usuario

ST

ST X-NUCLEO-IDW01M1 Manual de usuario

ST

ST STEVAL-IFS013V2 Manual de usuario

ST

ST STEVAL-IFP046V1 Manual de usuario

ST

ST X-NUCLEO-OUT10A1 Manual de usuario

ST

ST STSW-L9026-Y0 Manual de usuario

ST

ST X-NUCLEO-IDB05A2 Manual de usuario

ST

ST X-NUCLEO-OUT02A1 Manual de usuario

ST

ST EVSPIN958 Manual de usuario

ST

ST X-NUCLEO-OUT13A1 Manual de usuario

ST

ST EVSPIN948 Manual de usuario

ST

ST TIP120 Manual de usuario

ST

ST X-NUCLEO-OUT09A1 Manual de usuario

ST

ST STM8SVLDISCOVERY Instrucciones de instalación y funcionamiento

ST

ST X-CUBE-OUT3 Manual de usuario

ST

ST STM32F3DISCOVERY Manual de usuario

ST

ST STR9 Manual de usuario

ST

ST STM32U5 Manual de usuario

ST

ST X-NUCLEO-IHM03A1 Manual de usuario

ST

ST X-NUCLEO-IHM11M1 Manual de usuario

ST

ST 32L152CDISCOVERY Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Advantech

Advantech ASMB-935 Series Manual de usuario