SSV Works SWITCH WORKS ALPHA 12 SW-E12 Manual de usuario

SW-E12

12 OUTPUT

ELECTRONIC ACCESSORIES

SMART SWITCHER

Please read and understand these

instructions completely before

installation to avoid possible injury, or

damage to the accessory or vehicle.

WARRANTY INFORMATION:

All SWITCH Works Electronics are covered by a limited 1 year warranty against defects in

material or workmanship. Contact SSV Works for further warranty information.

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

PARTS CONTENTS

B-H2513

CONTROLLER ACCESSORY ILLUMINATION

L1 (OUTPUT)

L2 (OUTPUT)

L3 (OUTPUT)

L4 (OUTPUT)

L5 (OUTPUT)

L6 (OUTPUT)

B-H2514

Controller Mounting

Bracket

LCD Touch Button

Controller

1 3/8”Pan Head

Screw & Locknut

RAM Mount

Ball Adapter

Low Current

Output Harness

High Current

Output Harness

High Current Pigtail

& Ring Terminal (x6)

SWITCH Works 12 Circuit

Brain Module

RAM Mount 1”

Ball Base

RAM Mount Double

Socket Arm

Low Current

Pigtail (x6)

Flat Head, Thread

Cut Screw (x4)

#4 AWG Power/Ground Cable Set

3 ft or10 ft

M8 Flange Bolt &

SS Split Washer (x2)

Fuse holder with 100A

mini ANL fuse

Faceplate & Gasket Pack

Brain Module Power

Harness

Dummy Plug

To Battery

To Ground

USB Port

(for software updates only)

High Current

Outputs x6

Low Current

Outputs x6

Illumination

ACC

B+

CONNECTION DIAGRAM

NOTE: Controller MUST be connected first before power is applied to the switcher.

HIGH CURRENT

OUTPUT DEVICE BUTTON # OUTPUT FUNCTION

LOW CURRENT

OUTPUTS DEVICE BUTTON OUTPUT FUNCTION

To make programming the SWITCH Works module easier, we recommend mapping your

accessories with the cheat sheet below. Determine which accessory you're connecting to

each individual output; which button you want to control the output (button used is not

determined by output location); and, which function you want to achieve for the output

(ON/OFF, Strobe, etc.).

DEVICE LIST

1. Attach the RAM Mount ball adapter to the

Controller Mounting Bracket and secure with

the 1 3/8”pan head screw and locknut.

2.Attach the Controller Mounting Bracket to

the LCD Touch Button Controller using the

4 flat head, thread cut screws provided.

Ground

To Battery

B+

4. Connect the 4AWG power and ground wires

to the brain module using the M8 flange bolt

and split washer.

3. Cut the 4AWG power and ground wires to the

required length to reach the battery. Install the

fuse holder provided in the kit to the 4 AWG

power wire. Wait to connect the power and

ground wires to the battery until all other

installations steps are completed.

To Module

INSTALLATION

Skip step 1 and 2 if using vehicle specific kit.

5. Plug the B-H2513 harness to the SWITCH

Works Brain.

6. Plug the LCD Touch Button Controller to the

B-H2513 harness.

8. Splice your devices to the to the high current and

low current harnesses accordingly. Then plug in the

harnesses to the module.

High Current: 25 amps each x6

Low Current: 5 amps each x6

NOTE: If outputs L1-L6 are not going to be used plug in

the dummy connector included in the accessory box.

*When all other Installation steps are completed,

connect power and ground wires to the Battery.

B+

7. Tap ACC wire to a switched 12 volt power

source. Tap Illumination wire to headlight power

for dimming function.

NOTE: LCD Touch Button Controller MUST be con-

nected before applying ACC power to the switcher.

High Current

Outputs x6

Low Current

Outputs x6

B+

Illumination

ACC

INSTALLATION

1 2 3 4

5 6 7 8

910 11 12

SWITCH Works LCD Touch Controller Button Layout

The SWITCH Works LCD Touch Controller features 60

user programmable buttons and 64 icons to choose from

to control electrical devices. Unit is defaulted to 1 page

of 12 buttons from the factory. Additional button pages

can be turned on in GENERAL menu. See section on

GENERAL SETTINGS.

Press MENU button to enter settings.

Output Description Devices

H1 High Current Output 1

Light Bars, Sound System, Horn, etc.

(25 amps max each output)

H2 High Current Output 2

H3 High Current Output 3

H4 High Current Output 4

H5 High Current Output 5

H6 High Current Output 6

L1 Low Current Output 1

Dome Light, Turn Signals, Rock Lights,

Low Current LEDs, etc.

(5 amps max each output)

L2 Low Current Output 2

L3 Low Current Output 3

L4 Low Current Output 4

L5 Low Current Output 5

L6 Low Current Output 6

OUTPUT SETTINGS

Output Button Button

Icon StatusMenu

Current

Limit

Back General About

Output

Back

H1 Battery Latched

Timer

Disabled

Program the function of each added accessory/output by selecting OUTPUT. Select

number (H1 to H6 and L1 to L6) and set the power source and function for each output.

PROGRAMMING

OUTPUT SETTINGS

Output Power Source Description

High Current

H1 to H6

(25 amps each)

Low Current

L1 to L6

(5 amps each)

Battery Output stays on with ignition (ACC) off

Ignition Output turns on with ignition (ACC) on

Ign. Memory Saves last device status (defaults to OFF)

Function

Latched Press ON, Press OFF

Latch Flash Press to FLASH, Press OFF

Latch Strobe Press to STROBE, Press OFF

Hold Strobe Press ON, Press OFF, Press & Hold to Strobe

Dimmer Press ON, Press OFF, Press & Hold for Dimmer Function

Moment Press & Hold for ON, Release for OFF

Moment Flash Momentary FLASH

Moment Strobe Momentary STROBE

Timer Disabled

Timed Output

(On for 30s, 1m to 5m)

(not available in Momentary functions)

Select OUTPUT number (H1 to H6 and L1 to L6) and set the power source and function

for each output.

Output

Back

Battery Latched

Timer

Disabled

PROGRAMMING

BUTTON SETTINGS

Function

Button Number H1 H2 H3 H4 H5 H6 L1 L2 L3 L4 L5 L6

B1 On Off Off Off Off Off Off Off Off Off Off Off

B2 Off On Off Off Off Off Off Off Off Off Off Off

Button

Back

B1 On O O

Light Bar

H1 H2 H3

Page

Select button number and set the output you want each button to turn ON or OFF. Note

that a button can be set to control more than one output. An example is to turn all High

Current outputs (H1 to H6) On or Off using one button.

BUTTON ICONS

Select the icon for each button used. Icon turns colored when selected. Press the BACK

button once all icons have been assigned to the buttons.

STATUS - Module

Status

Back

Module

76.5 F 2.3A 12.4V

The SWITCH Works LCD Touchscreen controller is capable of controlling two brain modules.

Select module 1 or 2 (If two brains are connected) to show TEMPERATURE, total CURRENT

DRAW and VOLTAGE.

Button

Back

Page

Left Arrow

Right Arrow

Hazard

Dome Light

Horn

Light Bar Whip Light

PROGRAMMING

Output Button Button

Icon StatusMenu

Current

Limit

Back

General

About

Output Button Button

Icon StatusMenu

Current

Limit

Back

General

About

Output Button Button

Icon StatusMenu

Current

Limit

Back

General

About

Status

Back

Module Output

STATUS - Output

Status

Back

Output

76.5 F 2.3A

O

The SWITCH Works LCD Touchscreen controller can show TEMPERATURE, CURRENT DRAW, STATUS

(On/Off) and SHORT CIRCUIT Protection Status of each used output.

CURRENT LIMIT

Status

Back

Output

H1P180A

Set the maximum current output of the SWITCH Works switcher module. The module is defaulted to

80 Amps. Adjust the module current output to match the total current draw of all devices connected.

NOTE: Adjust the current output based on the vehicle’s electrical current capacity.

Status

Back

Output

H1P180A

PRIORITY SHUTDOWN

The SWITCH Works controller constantly monitors the current draw and temperature of the system. It

offers a Priority Shutdown feature to prevent the system from over-current draw and over heating.

P1 - Highest Priority - Last output to turn off

P12 - Least Priority - First Output to turn off

Select which output (H1 to H6 and L1 to L6) has the Highest Priority and Least Priority.

Status

Back

Output

H1P180A

High Current Output 1

will be last to turn off

Status

Back

Output

L1P12

80A

Low Current Output 1

will be first to turn off

Status

Short Circuit

Protection

PROGRAMMING

Output Button Button

Icon StatusMenu

Current

Limit

Back General About

Status

Back

Module Output

Tabla de contenidos

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario