Spirax Sarco DLV7 Manual de usuario

IM-P204-03 CH Issue 8

1. Safety information

2. General product

information

3. Installation

4. Maintenance -

DN15 to DN32 valves

5. Maintenance -

DN40 to DN100 valves

6. Spare parts

Printed in GB

IM-P204-03

CH Issue 8

2046050/8

DLV7 SG Iron

Pressure Reducing Valve

Installation and Maintenance Instructions

IM-P204-03 CH Issue 8

Safe operation of the unit can only be guaranteed if it is properly installed,

commissioned and maintained by a qualified person (see Section 1.11) in compliance

with the operating instructions. General installation and safety instructions for

pipeline and plant construction, as well as the proper use of tools and safety equipment

must also be complied with.

Warning

Care should be exercised when handling gaskets since the stainless steel reinforcing

strip can easily inflict cuts.

1.1 Intended use

Referring to the Installation and Maintenance Instructions, name-plate and Technical

Information Sheet, check that the product is suitable for the intended Use/application.

The products listed below comply with the requirements of the European Pressure

Equipment Directive 2014/68/EU and carry the mark when so required.

The products fall within the following Pressure Equipment Directive categories:

Product Group 1

gases

Group 2

gases

Group 1

liquids

Group 2

liquids

DLV7

DN15 – DN40 PN16 and PN25 -SEP - -

DN50 PN16 -SEP - -

DN50 PN25 - 1 - -

DN65 – DN100 PN16 and PN25 - 1 - -

WS4 -SEP - -

WS4-3 - 1 - -

i) The products have been specifically designed for use on steam which is in

Group 2 of the above mentioned Pressure Equipment Directive. The product's

use on other fluids may be possible but, if this is contemplated, Spirax Sarco

should be contacted to confirm the suitability of the product for the application

being considered.

ii) Check material suitability, pressure and temperature and their maximum and

minimum values. If the maximum operating limits of the product are lower than

those of the system in which it is being fitted, or if malfunction of the product

could result in a dangerous overpressure or over temperature occurrence, ensure

a safety device is included in the system to prevent such over-limit situations.

iii) Determine the correct installation situation and direction of fluid flow.

iv) Spirax Sarco products are not intended to withstand external stresses that may

be induced by any system to which they are fitted. It is the responsibility of the

installer to consider these stresses and take adequate precautions to minimize

them.

v) Remove protection covers from all connections and protective film from all name-

plates, where appropriate, before installation on steam or other high temperature

applications.

1. Safety information

IM-P204-03 CH Issue 8

1.2 Access

Ensure safe access and if necessary a safe working platform (suitably guarded)

before attempting to work on the product. Arrange suitable lifting gear if required.

1.3 Lighting

Ensure adequate lighting, particularly where detailed or intricate work is required.

1.4 Hazardous substances in the pipeline

Consider what is in the pipeline or what may have been in the pipeline at some

previous time. Consider: flammable materials, substances hazardous to health,

extremes of temperature.

1.5 Hazardous environment around the product

Consider: explosion risk areas, lack of oxygen (e.g. tanks, pits), dangerous gases,

extremes of temperature, hot surfaces, fire hazard (e.g. during welding), excessive

noise, moving machinery.

1.6 The system

Consider the effect on the complete system of the work proposed.

Will any proposed action (e.g. closing isolation valves, electrical isolation) put any

other part of the system or any personnel at risk?

Dangers might include isolation of vents or protective devices or the rendering

ineffective of controls or alarms. Ensure isolation valves are turned on and off in a

gradual way to avoid system shocks.

1.7 Pressure systems

Ensure that any pressure is isolated and safely vented to atmospheric pressure.

Consider double isolation (double block and bleed) and the locking or labelling of

closed valves. Do not assume that the system has depressurised even when the

pressure gauge indicates zero.

1.8 Temperature

Allow time for temperature to normalise after isolation to avoid the danger of burns

and consider whether protective clothing (including safety glasses) is required.

1.9 Tools and consumables

Before starting work ensure that you have suitable tools and / or consumables

available. Use only genuine Spirax Sarco replacement parts.

1.10 Protective clothing

Consider whether you and / or others in the vicinity require any protective clothing

to protect against the hazards of, for example, chemicals, high / low temperature,

radiation, noise, falling objects, and dangers to eyes and face.

IM-P204-03 CH Issue 8

1.11 Permits to work

All work must be carried out or be supervised by a suitably competent person.

Installation and operating personnel should be trained in the correct use of the

product according to the Installation and Maintenance Instructions.

Where a formal 'permit to work' system is in force it must be complied with.

Where there is no such system, it is recommended that a responsible person should

know what work is going on and, where necessary, arrange to have an assistant

whose primary responsibility is safety. Post ‘warning notices’ if

necessary.

1.12 Handling

Manual handling of large and / or heavy products may present a risk of injury. Lifting,

pushing, pulling, carrying or supporting a load by bodily force can cause injury

particularly to the back. You are advised to assess the risks taking into account the

task, the individual, the load and the working environment and use the appropriate

handling method depending on the circumstances of the work being done.

1.13 Residual hazards

In normal use the external surface of the product may be very hot. If used at the

maximum permitted operating conditions the surface temperature of some products

may reach temperatures of 250 °C (482°F). Many products are not self-draining. Take

due care when dismantling or removing the product from an installation (refer to

'Maintenance instructions').

Self-acting valves may operate unexpectedly during normal service. The risk of

personal injury should be assessed for each installation. Where appropriate, suitable

guarding should be fitted.

1.14 Freezing

Provision must be made to protect products which are not selfdraining against frost

damage in environments where they may be exposed to temperatures below freezing

point.

1.15 Disposal

Unless otherwise stated in the Installation and Maintenance Instructions, this product

is recyclable and no ecological hazard is anticipated with its disposal providing due

care is taken.

1.16 Returning products

Customers and stockists are reminded that under EC Health, Safety and Environment

Law, when returning products to Spirax Sarco they must provide information on any

hazards and the precautions to be taken due to contamination residues or mechanical

damage which may present a health, safety or environmental risk. This information

must be provided in writing including Health and Safety data sheets relating to any

substances identified as hazardous or potentially hazardous.

IM-P204-03 CH Issue 8

Note: The DLV is not suitable for liquid applications

2.1 Description

The DLV pressure reducing valve is a direct acting self-powered valve of robust

construction, designed to operate under arduous conditions - Ideal for steam applications.

The valve is controlled by downstream pressure acting directly on the diaphragm to oppose

a 'set' spring force. Under stable conditions diaphragm force and spring force are in a state

of balance, but an increase or decrease in demand raises or lowers the downstream pressure

which in turn acts against the spring to close or open the valve to adjust the flowrate and

maintain a constant downstream pressure.

The DLV is 'routine' maintenance free. It is a single seat, bellows sealed valve available in

sizes ranging from DN15 to DN100 flanged EN 1092 PN16 and PN25 with downstream

pressure ranges of between 0.2 bar to 13 bar.

Standards and approvals

This product fully complies with the requirements of the European Pressure Equipment

Directive 2014/68/EU and carries the mark when so required.

Certification

This product is available with a manufacturer's Typical Test Report. Note: All certification /

inspection requirements must be stated at the time of order placement.

Note: For further product data see Technical Information sheet TI-P204-04.

2. General product information

IM-P204-03 CH Issue 8

The product must not be used in this region.

A-B-C Flanged EN 1092 PN16.

A-D-E Flanged EN 1092 PN25.

Body design conditions PN25 PN16

Maximum design pressure 25 bar g @ 100 °C 16 bar g @ 100 °C

Maximum design temperature 250 °C @ 21.8 bar g 250 °C @ 13.9 bar g

Minimum design temperature 0°C 0°C

Maximum operating temperature 250 °C @ 21.8 bar g 250 °C @ 13.9 bar g

Minimum operating temperature 0°C 0°C

Note: For lower operating temperatures consult Spirax Sarco

Maximum differential pressure 16 bar g

Designed for a maximum cold hydraulic test pressure of: 24 bar g

Note: With internals tted, test pressure must not exceed 16 bar g

Pressure bar g

Temperature °C

Steam

saturation

curve

A B D

C E

2.2 Pressure / temperature limits

IM-P204-03 CH Issue 8

Fig. 1 DN15 to DN32 Fig. 2 DN40 to DN100

2.3 Available types:

The DLV7 is available with the following pressure ranges:

Valve +Actuator and Size Pressure range

(bar)

Actuator

PN rating

DLV71 DN100 0.5 - 1.5 2.5

DLV72

DN15 to DN50 0.2 - 1.8

2.5

DN65 to DN80 0.4 - 1.8

DLV73 DN100 1.0 - 4.0 6.0

DLV74

DN15 to DN80 1.0 - 5.5 16.0

DN100 3.5 - 13 16.0

DLV75 DN15 to DN80 4.0 - 13 25.0

IM-P204-03 CH Issue 8

2.4 Water seal pot - WS4 / WS4-3 (optional extra)

Fig. 3 Water seal pot

Water fill connection

Actuator pressure signal

Technical details

Available types

WS4 The WS4 is for normal applications up to a volume of 1 litre.

WS4-3 The WS4-3 has a larger 3 litre volume and is recommended

where there is rapid fluctuation of pressure or load.

Connection sizes

Inlet

" BSP male

Screwed WS4 " NPT male BS 21

Screwed WS4-3 ½" BSP male BS 21

½" NPT male

DN10

Butt weld WS4 DN15

Outlet Screwed " BSP female BS 21 with 8 mm compression fittings

Materials

Housing Carbon steel

Downstream pressure pipe

IM-P204-03 CH Issue 8

2.5 Pressure / temperature limits - WS4 / WS4-3

The product must not be used in this region.

Body design conditions PN25

Maximum design pressure 25 bar g @ 120 °C

Maximum design temperature 225 °C @ 21 bar g

Minimum design temperature 0°C

Maximum operating pressure for saturated steam 21 bar g

Maximum operating temperature 225 °C @ 21 bar g

Minimum operating temperature 0°C

Note: For lower operating temperatures consult Spirax Sarco

Maximum differential pressure 25 bar g

Designed for a maximum cold hydraulic test pressure of 40 bar g

Note: With internals fitted, test pressure must not exceed 25 bar g

Pressure bar g

Temperature °C

Steam

saturation

curve

IM-P204-03 CH Issue 8

Note: Before actioning any installation observe the 'Safety information' in Section 1.

3.1 General information

The valve should be installed in a horizontal pipeline.

For operating temperatures below 125 °C the valve may be installed either vertically upwards

or vertically downwards (see Figure 4).

For operating on steam or temperatures above 125 °C the valve must be installed vertically

downwards with the spring / actuator below the pipework with a water seal pot fitted on the

downstream control signal line to the actuator, a typical installation is shown in Figure 5.

Care should be taken to install the valve correctly as indicated by the direction of flow arrow

on the valve body.

3. Installation

Fig. 4 Typical installation for

downstream temperatures below 125 °C

the valve can alternatively be mounted

vertically upwards.

* 1 m or 15

pipe diameters

minimum

* *

Steam

Condensate

Fig. 5 Typical installation for downstream

temperatures above 125 °C

* *

WS4 water seal pot

Steam

Condensate

3.2 Pressure control pipe

The valve actuator signal connection must be piped directly to the downstream side. To

provide a good control signal the downstream sensing point should be positioned a minimum

of 1 metre or 15 pipe diameters away from the valve or change in pipework direction on either

side. It is recommended that the actuator signal pipe should be 8 mm diameter copper or

stainless steel of 1 m minimum length.

3.3 Preventing dirt

Before installing the valve the system pipework should be flushed out to remove any residual

dirt or scale that may be present. The valve should be protected by a pipeline strainer of the

same size as the upstream pipework. For steam applications the strainer should be installed

on its side to prevent the accumulation of water.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de Spirax Sarco

Spirax Sarco

Spirax Sarco BSA3-BD Manual de usuario

Spirax Sarco

Spirax Sarco DP143 Manual de usuario

Spirax Sarco

Spirax Sarco HM Series Manual de usuario

Spirax Sarco

Spirax Sarco FTC80 Manual de usuario

Spirax Sarco

Spirax Sarco SRV2S Manual de usuario

Spirax Sarco

Spirax Sarco 25BP Manual de usuario

Spirax Sarco

Spirax Sarco Spira-trol KE73 Manual de usuario

Spirax Sarco

Spirax Sarco MkII Guía

Spirax Sarco

Spirax Sarco LCV6 Manual de usuario

Spirax Sarco

Spirax Sarco SafeBloc DBB3 Manual de usuario

Spirax Sarco

Spirax Sarco M80i ISO Manual de usuario

Spirax Sarco

Spirax Sarco 211 Manual de usuario

Spirax Sarco

Spirax Sarco M10S Manual de usuario

Spirax Sarco

Spirax Sarco PM6 Manual de usuario

Spirax Sarco

Spirax Sarco 25P Manual de usuario

Spirax Sarco

Spirax Sarco TD62LM Manual de usuario

Spirax Sarco

Spirax Sarco TD120 Manual de usuario

Spirax Sarco

Spirax Sarco PV4 Manual de usuario

Spirax Sarco

Spirax Sarco DP27S Manual de usuario

Spirax Sarco

Spirax Sarco FTS14 Manual de usuario

Spirax Sarco

Spirax Sarco TD3-3 Manual de usuario

Spirax Sarco

Spirax Sarco WAV1 Manual de usuario

Spirax Sarco

Spirax Sarco DP17 Manual de usuario

Spirax Sarco

Spirax Sarco DCV4 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario