SPI Infrared SBE1 M2D Manual de usuario
SPI CORP M2D TRIP EOIR GIMBAL SYSTEM
SBE1 Recording, Tracking
+ IP Conversion
Module
User Manual
!
Ver 2.0
This document is the property of SPI CORP www.x20.org
TRIP Manual
Ver : 1.8
www.x20.org
Compilation and Publication Notice
This manual covers the latest product descriptions and specifications.
The contents of this manual and the specifications of this product are
subject to change without notice.
SPI reserves the right to make changes without notice in the
specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
For Further information please contact
SPI CORP
Table of Content
- Page !of !–2 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
1. Introduction 4
2. Architecture 5
3. Physical connectivity 6.......................................................................
3.1. Wire(Harness( 7(
4. Functionality 8
5. IP Setting 10
6. SBE1 Board Setting 11.......................................................................
7. SBE1 Board Firmware Update 23......................................................
8. SBE1 Video Preview 24......................................................................
9. SBE1 Video Preview With VLC 31....................................................
10.KLV Metadata 34................................................................................
Appendix A : Version Control 40.............................................................
- Page !of !–3 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
1. Introduction
The document includes the user manual of SPI’s Recording, Tracking
and IP conversion (SBE1) OEM board.
!
Note: The SBE1 board supports M2D protocols. !
- Page !of !–4 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
2. Architecture
The architecture of the SBE1 Module is depicted in the following:
!
!
!
!
!
!
!"
- Page !of !–5 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
3. Physical connectivity
The SBE1 board includes the following connectors:
Designat
ion
Connect,to
Type
Pin,Description
J1
M2D&camera
Molex&
PicoBladeT
M&10&pin
Pin& Function&
1& Camera&Power&IN&(12-32V)&
*max&voltage&depends&on&camera&
2& GND&
3& RS232&RX&(TRIP&Out,&Camera&In)&
4& RS232&TX&(TRIP&In,&Camera&out)&
5& GND&
6& NC&
7& NC&
8& NC&
9& Analog&Video&In&
10& Analog&Video&Return&(VIDEO_GND)&
J2
Host&Serial&
Port,&Analog&
Display,&Power
Molex&
PicoBladeT
M&10&pin
Pin& Function&
1& External&Power&IN&(12-32V)&
*max&voltage&depends&on&camera&
2& GND&
3& RS232&RX&(Host&Out,&TRIP&In),&&
Dual&function&(External&RS232&Control&or&GPS)&
4& RS232&TX&(Host&In,&TRIP&out)&
5& GND&
6& DBG_RX& (for& factory& use& only,& leave&
unconnected)&
7& DBG_TX& (for& factory& use& only,& leave&
unconnected)&
8& DBG_GND&
9& Analog&Video&Out&
10& Analog&Video&Return&(VIDEO_GND)&
J3
Input&(HDMI)
MicroHDMI
Standard&Micro&HDMI&
Connector
J4
Digital&Display&
(HDMI)
MicroHDMI
Standard&Micro&HDMI&
Connector
- Page !of !–6 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
3.1. Wire Harness
J5
Host&USB&Port
Molex&
PicoBladeT
M&4&pin
Pin& Function&
1& USB_HOST_VCC&(+5V)&&
Supplied&from&TRIP&to&Target&
2& USB_HOST_DATA+&(DP)&
3& USB_HOST_DATA-&(DM)&
4& GND&
J6
Host& Ethernet&
Port
Molex&
PicoBladeT
M&5&pin
Pin& Function&
1& ETH_TX+&
2& ETH_TX-&
3& ETH_RX+&
4& ETH_RX-&
5& ETH_GND&(optional)&
J7
Memory&card
MicroSD&
slot
Standard&MicroSD&slot
P.N
Connector
Description
2042
J1
Connecting SBE1 to Camera
The wire harness includes two Molex
51021-1000 connectors and 50cm [19.5”] long
ultra flexible wires.
2042
J2
Connecting SBE1 to PIB
The wire harness includes two Molex
51021-1000 connectors and 50cm [19.5”] long
ultra flexible wires.
2081
J5
Connecting SBE1 to USB Host
The wire harness includes a Molex 51021-0400
connector and USB Receptacle Connector
(Female) and 50cm [19.5”] long ultra flexible
wires.
- Page !of !–7 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
J3 cable can be sourced from any video store
4. Functionality
The SBE1 is available in two different flavors:!
SD – Standard Definition!
HD – High Definition!
!
Common functions that are supported by both flavors:
•IP Streaming of captured video using the following format:!
Mpeg2Ts over RTP with H264 compression.
•Receiving protocol commands from the user through RS232 (J2
connector) or through IP over Ethernet (J6 connector)
•Sending protocol commands to the camera through J1
connector
•Recording the video on the SD card upon protocol command.
Adding GPS meta data to stored frames.
•Tracking object in the video upon protocol command.
•Notify loss of object tracking through protocol.
•Detecting motion in the video upon protocol command.
•Notify motion detection through protocol.
2082
J6
Connecting SBE1 to Ethernet
The wire harness includes a Molex 51021-0500
connector and RJ-45 Jack (Female) and 50cm
[19.5”] long ultra flexible wires.
- Page !of !–8 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
The SBE1-SD board performs the following additional functions:
•Autodetection of PAL/NTSC video from the camera through J1
connector
•Outputting digital video on J4 HDMI connector, !
When the input video is PAL than the HDMI output transmits:
576p@50Hz format.!
When the input video is NTSC than the HDMI output
transmits: 480p@60Hz format.
The SBE1-HD board performs the following additional functions:
•Capture digital video from the camera through J3 HDMI
connector, the captured format is 720p@60Hz
•Outputting digital video on J3 HDMI connector, !
The HDMI output transmits: 720p@60Hz.!
- Page !of !–9 41
- SPI Proprietary and Confidential Information -
TRIP Manual
Ver : 1.8
www.x20.org
5. IP Setting
The SBE1 board default IP address is: 192.168.0.201 with the
following subnet mask: 255.255.255.0
In cases that there is no possible way to update the host IP address due
to lack of administrative rights the SBE1 Discovery Tool offers a way
to find units and update their IP settings from any network
transcending subnet settings.!
Open the discovery tool:
In order to display all the units that are available on network!
Press on the Find Boards button on the Discovery Units:
- Page !of !–10 41
- SPI Proprietary and Confidential Information -
Tabla de contenidos
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
