SPEECON 7300PA series Manual de usuario

4H358D0130001

VARIABLE TORQUE INVERTER WITH ENERGY SAVING CONTROL

INVERTER

7300PA

INSTRUCTION MANUAL

220V Class 3Φ25~125HP

440V Class 3Φ25~500HP

Please hand this manual to the end-users. It will be of

great help for their daily operation, maintenance,

inspection and troubleshooting.

BEFORE INSTALLATION & USE

1. Ensure nameplate data corresponds with your requirements.

2. Ensure the apparatus is undamaged.

WARNING

The following safety precautions must be observed:

1. Electric apparatus and electricity can cause serious or fatal injury if the

apparatus is improperly installed, operated or maintained.

Responsible personnel must be fully trained to understand the

hazards to themselves and others before being involved in installing,

operating, maintaining and decommissioning electrical apparatus.

European Union Safety information can be obtained from such as:

BS4999; EN60204-11 EN292-1 EN294

IEE Wiring Regulations

Particular industries and countries have further safety requirements.

Refer to their trade safety bodies, British Standards Institution, Dept.

of Trade & Industry, etc., for further information. For instance, in the

USA, refer to NEMA MG2, the National Electrical Code, local safety

requirements, etc.

2. When servicing, all power sources to the apparatus and to the

accessory devices should be de-energized and disconnected and all

moving parts at standstill.

3. Safety guards and other protective, devices must neither be bypassed

nor rendered inoperative.

4. The apparatus must be earthed. Refer to relevant standards such as

EN60204-1, IEE Wiring Regulation etc.

5. A suitable enclosure must be provided to prevent access to live parts.

Extra caution should be observed around apparatus that is

automatically started or has automatic resetting relays or is remotely

started in case such starting means has not been properly disabled

and the apparatus starts unexpectedly.

－1－

CAUTION AND WARNING:

WARNING

 Do not change the wiring while power is applied to the circuit.

 After turning OFF the main circuit supply, do not touch circuit components until CHARGE

LED is extinguished.

 Never connect power circuit output U (T1), V (T2), W (T3) to AC power supply.

 When the retry function (Cn-36) is selected, motor may restart suddenly after being

stopped by momentary power loss.

CAUTION

 When mounting units in a separate enclosure, install a fan or other cooling device to keep

the intake air temperature below 45℃.

 Do not perform a withstand voltage test to the inverter.

 All the constants of the inverter have been factory preset. Do not change the settings

unnecessarily.

－2－

CONTENTS

PART I INSTALLATION MANUAL Pages

1. GENERAL ...............................................................................................................................5

1.1 SAFE OPERATION NOTES ..............................................................................................5

1.2 PRODUCT CHANGES ......................................................................................................5

2. RECEIVING............................................................................................................................6

3. INSTALLATION.....................................................................................................................7

3.1 MOUNTING SPACE..........................................................................................................7

3.2 LOCATION.........................................................................................................................8

4. WIRING...................................................................................................................................9

4.1 NOTES ON WIRING TO PERIPHERAL UNITS .............................................................9

4.2 CONNECTION DIAGRAM.............................................................................................10

4.3 TERMINAL FUNCTION .................................................................................................11

4.3.1 MAIN CIRCUIT TERMINALS ............................................................................11

4.3.2 CONTROL CIRCUIT TERMINALS ....................................................................11

4.3.3 MAIN CIRCUIT SCHEMATIC.............................................................................12

4.4 WIRING PARTS ...............................................................................................................13

4.4.1 RECOMMENDED WIRING PARTS....................................................................13

4.4.2 CAUTIONS FOR WIRING ...................................................................................15

5. TEST OPERATION..............................................................................................................17

5.1 CHECK BEFORE TEST OPERATION ...........................................................................17

5.2 SETTING THE LINE VOLTAGE SELECTING CONNECTOR ....................................17

6. MAINTENANCE ..................................................................................................................18

6.1 PERIODIC INSPECTION ................................................................................................18

6.2 SPARE PARTS ..................................................................................................................19

7. SPECIFICATIONS ...............................................................................................................21

8. DIMENSIONS .......................................................................................................................23

9. PERIPHERAL AND OPTIONS ..........................................................................................26

9.1 AC REACTOR..................................................................................................................26

9.2 NOISE FILTER.................................................................................................................27

9.2.1 INPUT NOISE FILTER .........................................................................................27

9.2.2 EMI SUPPRESSION ZERO CORE ......................................................................28

9.3 BRAKING RESISTOR AND BRAKING UNIT .............................................................29

9.4 OTHERS ...........................................................................................................................30

9.4.1 DIGITAL OPERATOR WITH EXTENSION WIRE ............................................30

9.4.2 ANALOG OPERATOR .........................................................................................31

9.4.3 LED DIGITAL OPERATOR..................................................................................31

9.4.4 1 TO 8 PID RELAY CARD ...................................................................................31

9.4.5 RS-485 COMMUNICATION OPTION CARD ....................................................32

－3－

PART II OPERATION MANUAL Pages

1. DESCRIPTION OF USING 7300PA...................................................................................34

1.1 Using LCD (OR LED) digital operator.............................................................................34

1.2 DRIVE mode and PRGM mode displayed contents .........................................................36

1.3 Parameter description........................................................................................................37

1.4 Sample example of using LCD digital operator................................................................38

2. SETTING USER CONSTANT ............................................................................................40

2.1 Frequency Command An-□□.........................................................................................40

2.2 Parameters Can Be Changed during Running Bn-□□....................................................41

2.3 Control Parameters Cn-□□.............................................................................................49

2.4 System Parameters Sn-□□..............................................................................................64

2.5 Monitoring Parameters Un-□□.....................................................................................105

2.6 Monitoring Parameters Hn-□□.....................................................................................107

2.7 Order Parameters On-□□..............................................................................................109

3. FAULT DISPLAY AND TROUBLE SHOOTING........................................................... 111

APPENDIX:

A. ENERGY-SAVING CONTROL..........................................................................................119

B. PID CONTROL....................................................................................................................121

C. RS-485 COMMUNICATION CONNECTION DIAGRAM ...............................................126

D. SINK/SOURCE TYPICAL CONNECTION DIAGRAM...................................................128

E. RS-232C SERIAL COMMUNICATIONS CONNECTION DIAGRAM............................130

F. NOTES ON APPLICATION OF MOTORS.........................................................................131

G. PERIPHERAL UNIT NOTES .............................................................................................132

H. CIRCUIT PROTECTION AND ENVIRONMENTAL RATING NOTES..........................133

I . INVERTER HEAT LOSS…………………………………………………………………..135

J. DRIVE INPUT FUSES……………………………………………………………………..136

K.CERTIFICATION FOR THE INVERTER…………………………………………………137

－4－

PART I

INSTALLATION MANUAL

－5－

1. GENERAL

1.1 SAFE OPERATION NOTES

Read this installation manual thoroughly before installation, operation, maintenance or

inspection of the inverter. Only authorized personnel should be permitted to perform

maintenance, inspections or parts replacement.

In this manual, notes for safe operation are classified as:

"WARNING" or "CAUTION".

: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury to personnel.

: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury to personnel and damage to equipment. It may

also be used to alert against unsafe practices.

This inverter has been placed through demanding tests at the factory before shipment. After

unpacking, check for the following:

1. Verify that part numbers on shipping carton and unit match the purchase order sheet

and/or packing list.

2. Do not install or operate any inverter which is damaged or missing parts.

3. Do not install or operate any inverter which has no QC marking.

Contact your local distributor or TECO representative if any of the above have been found.

1.2 PRODUCT CHANGES

TECO reserves the right to discontinue or make modifications to the design of its products

without prior notice, and holds no obligation to make modifications to products sold previously.

TECO also holds no liability for losses of any kind which may result from this action.

WARNING

CAUTION

－6－

2. RECEIVING

CAUTION

This 7300PA has been put through demanding tests at the factory before shipment. After

unpacking, check the followings.

 Verify the received product with the purchase order sheet (invoice) and/or packing list.

 Transit damage.

If any part of 7300PA is damaged or lost, immediately notify the shipper.

■NAMEPLATE DATA ( 220V CLASS 75HP example )

220V CLASS INVERTER

JNTFBGBA0075JK- - -

MODEL

INPUT

OUTPUT

SER. NO.

AC 3PH 200-230V 50/60Hz

AC 3PH 0-230V 81KVA 212A

■MODEL DESIGNATION

JNTFBGBA0075JK ---

Inverter Series

7300PA

Enclosures and

mountings

BA：Open chassis type（IEC IP00）

BB：Enclosed, wall-mounted type（NEMA-1）

Reserved

Voltage

Applicable maximum

motor output（HP）

0025：25HP

0500：500HP

JK:220V, 60Hz(200V, 50Hz)

AZ:440V, 60Hz(400V,50Hz)

Inverter Model

Input Spec.

Output Spec.

Series No.

CE Mark &CSA Mark

－7－

3. INSTALLATION

CAUTION

 Never move, lift or handle the 7300PA cabinet by the front cover.

 Lift the cabinet from the bottom.

 Do not drop the inverter.

3.1 MOUNTING SPACE

Install 7300PA vertically and allow sufficient space for effective cooling as shown in Fig. 1.

(a)FrontView (b)SideView

Note: For product external dimensions and mounting dimensions,

refer to “DIMENSIONS” on page 23.

Fig. 1 Mounting Spaces

1.18in(30mm)

OR MORE

1.18in(30mm)

OR MORE

ALLOWABLE

TEMPERATURE OF

CONTROL PART: 131

℉(55℃)

5.9in(150mm)

OR MORE

5.9in(150mm)

OR MORE

AIR

FRONT

COVER OPEN CHASSIS TYPE:

113℉(45℃)

ENCLOSED

WALL-MOUNTED

TYPE: 104℉(40℃)

－8－

3.2 LOCATION

Location of the equipment is important to achieve proper performance and

normal operating life. The 7300PA should be installed in areas where the

following conditions exist:

 Protected from rain or moisture.

 Protected from direct sunlight.

 Protected from corrosive gases or liquids.

 Free from airborne dust or metallic particles.

 Free from vibration.

 Free from magnetic noise (e.g. welding machines, power units)

 Ambient temperature:

+14 to 104℉, -10 to +40℃(For enclosed type),

+14 to 113℉, -10 to +45℃(For open chassis type)

 Free from combustible materials, gases, etc.

CAUTION

When mounting multiple units in a common enclosure, install a cooling

fan or some other means to cool the air entering the inverter to at least

113℉(45℃) or below.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario