Spectrum Digital XDS510USB Manual de usuario

XDS510USB JTAG Emulator

Installation Guide

IMPORTANT INFORMATION

About This Installation Guide

This Installation Guide is for the XDS510USB Emulator product. The XDS510USB Emulator

is a module to be attached to a PC for hardware engineers and software programmers to develop

DSP applications.

The text paragraphs in this Guide are very important for proper device functioning and for

preventing any possible damages on the XDS510USB Emulator device and project target board.

These paragraphs are shaded as in the following example. Please carefully read each of the

shaded text.

This is an example of a very important text paragraph mentioned above.

Introduction

Overview

XDS510USB Emulator is designed to use with digital signal processors (DSPS) operating at

1.0-5.0 volts. The emulator itself is a bus-powered USB device. It is fully plug and play

compatible and is fully powered by the host computer’s USB connection. The XDS510USB

Emulator operates with TI Code Composer Studio IDE debug tool and is fully compatible with

windows 98/SE/ME/2000/XP/VISTA.

Features

XDS510USB Emulator has the following features:

●

Supports Texas Instruments DSP with a JTAG (IEEE1149.1) interface: C2000, C5000,

C6000 ,OMAP platforms.

●

Supports Texas Instruments Code Composer Studio.

●

Supports 1.0-5.0 volt DSP devices.

●

USB compatible. Simple Connection, fully Plug-and-Play compatible-no jumpers, noswitch

settings.

●

Hot pluggable

●

Power provided by USB bus , no additional power supply is required.

QUICK Installation

Quick Install Procedures

This guide describes the steps to installing the XDS510USB Emulator in the following orders:

1. Install the XDS510USB Emulator hardware

2. Install the XDS510USB device driver

3. Make sure Code Composer Studio IDE is installed on the PC

4. Install the XDS510USB Emulator software

5. Configure Code Composer Studio IDE

6. Reset the XDS510USB Emulator and Reset the target DSP

7. Run CCS

The XDS510USB JTAG Emulator kit contains:

●

XDS510USB JTAG Emulator

●

USB interface cable

●

The XDS510USB driver disk

●

XDS510USB Emulator Installation Guide Reference Guide (this document)

Installation Requirements

●

Code Composer Studio IDE 1.2 or greater

●

A free USB port

●

233 MHZ or higher Pentium compatible CPU (500MHZ or higher Pentium III CPU or

equivalent is recommended)

●

Local CD-ROM drive

Supported Operating Systems

●

Windows98/ME/2000/XP/VISTA

Detailed Installation

What you will need

The following detailed list contains all items needed to install and run with the XDS510USB

JTAG Emulator.

●

PC with a free Universal Serial Bus (USB) port

●

XDS510USB JTAG Emulator

●

XDS510USB driver disk

●

USB interface cable

●

DSP target system

●

Code Composer Studio

The Hardware Installation

●

Remove power from the target DSP system.

●

Connect the keyed XDS510USB JTAG Emulator JTAG interface cable to the target board.

●

Apply power to the target DSP system.

●

Connect the XDS510USB JTAG Emulator to the host computer system using a USB cable.

The USB Device Drivers Installation

Driver installation for windows 2000/XP:

1. After plug the XDS510USB JTAG Emulator into the host computer’s USB port, the system

should display the Found New Hardware (Figure A-1) dialog box. This dialog box indicates

the computer operating system has found a new USB device.

Figure A-1

2. The system will prompt for new hardware detected and start the “Found New Hardware

Wizard” as shown in Figure A-2.

Figure A-2

3. Click on next and system will display the window as shown in Figure A-3.

Figure A-3

4. Check on “Search for a suitable driver for my device(Recommended)” and click on next. The

system will display a window as shown in Figure A-4.

Figure A-4

5. Check on “CD-ROM drives” and click on next. The system will prompt you to insert the

manufacturer’s installation disk, as shown in the Figure A-5.

Figure A-5

6. Click on Browse and locate the file usb510.Inf in the installation CD(TI DSP

Emulator\XDS510 USB_driver), or in the folder where you have downloaded the file into, as

shown in Figure A-6.

Figure A-6

7. Click on next, the following window will be displayed ,as shown in Figure A-7.

Figure A-7

8. Click on Finish. Set up is completed.

Installing the XDS510USB software

This installation assumes that the Code Composer Studio IDE has already been installed on

the PC. If not, please follow the directions for installing Code Composer Studio first. After

completing the installation procedure, you may return to the guide to complete the installation

procedure of the XDS510 Emulator.

Insert the XDS510USB driver disk into your CD-ROM, Double click on Setup.Exe(TI DSP

Emulator\XDS510 CCS_driver) to install the JTAG emulator tools for CCS.

In order to run the

application properly the XDS510 CCS Driver must reside in the same folder in which the

Code Composer Studio IDE is installed.For example,if the Code Composer Studio IDE

installed in E:\CCStudio_v3.3,the XDS510 CCS Driver must install in E:\CCStudio_v3.3.

NOTE

Be sure the Code Composer Studio has been installed before run Setup.exe. It’ll copy

files to the CCS install directory and create environment variable to enable the file usage

by CCS. If this step is missing, the XDS510USB can’t function properly.

CCS Emulate Configuration

XDS510USB JTAG Emulator has provided many typical emulate configuration. The user can

use them directly without modification.

1. Launch the Setup CCStudio v3.3 , the program will display the window as shown

in figure C-1.

Figure C-1

2. Select xds510 emulator in the platform list; Select your DSP type in the family list. The

program will list some typical configuration.

3. Double-click the item according to your target board .The new configuration will appear in

My System list in the System Configuration window.Configure the properties of your target

board and Set the proper gel file. Save the configuration and exit the setup program.

4. Connect your target board to the emulator, then power on the target board, launch the CCS.

Now, you can debug your target system using XDS510USB JTAG Emulator.

Figure C-2

Figure C-3

Tabla de contenidos

Otros manuales de Hardware de computadora de Spectrum Digital

Spectrum Digital

Spectrum Digital XDS510PP Manual de usuario

Spectrum Digital

Spectrum Digital XDS560R Manual de instrucciones

Spectrum Digital

Spectrum Digital XDS560v2 Manual de uso y cuidado

Spectrum Digital

Spectrum Digital C2000 Series Manual de uso y cuidado

Spectrum Digital

Spectrum Digital TMS320C5515 eZdsp Manual de uso y cuidado

Spectrum Digital

Spectrum Digital XEVM642 4VSX35 Manual de uso y cuidado

Spectrum Digital

Spectrum Digital XDS560R Manual de usuario

Spectrum Digital

Spectrum Digital AppBox C21 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario