Spectrum Controls Micro800 2080sc-IF4U Manual de usuario

Install Guide 
 
 
 
Micro800™
4 Ch Universal Analog Input Module 
(Catalog Number 2080sc-IF4U) 
Contents 
For More Information.................................................................................2 
Environment and Enclosure......................................................................2 
Prevent Electrostatic Discharge................................................................3 
Parts List ...................................................................................................4 
Insert Module into Controller.....................................................................5 
Wire the Module........................................................................................6 
Configuring the Module.............................................................................6 
Module Input Data.....................................................................................9 
Adding the IF4U to CCW.........................................................................11 
Electrical Specifications ..........................................................................12 
Environmental Specifications..................................................................14 
Hazardous Location Considerations .......................................................17 
Environnements dangereux....................................................................18 
 
 

Micro800™ 4 Ch Universal Analog Input Module 2

Publication 0100189-04 Rev. C

For More Information

PLC sample projects and documentation are available on our

website at www.spectrumcontrols.com

Environment and Enclosure

This equipment is intended for use in a Pollution

Degree 2 industrial environment, in overvoltage

Category II applications (as defined in IEC

publication 60664-1), at altitudes up to 2000 meters

(6562 ft) without derating.

This equipment is considered Group 1, Class A

industrial equipment according to IEC/CISPR

Publication 11. Without appropriate precautions,

there may be potential difficulties ensuring

electromagnetic compatibility in other environments

due to conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment.

It must be mounted within an enclosure that is

suitably designed for those specific environmental

conditions that will be present and appropriately

designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have

suitable flame-retardant properties to prevent or

minimize the spread of flame, complying with a flame

spread rating of 5VA, V2, V1, V0 (or equivalent) if

non-metallic. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent

sections of this publication may contain additional

information regarding specific enclosure type ratings

that are required to comply with certain product

safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding

Guidelines, Allen-Bradley publication 1770-

4.1, for additional installation requirements.

•NEMA Standards publication 250 and IEC

publication 60529, as applicable, for

explanations of the degrees of protection

provided by different types of enclosure

Micro800™ 4 Ch Universal Analog Input Module 3

Publication 0100189-04 Rev. C

Prevent Electrostatic Discharge

Electrostatic discharge can damage integrated

circuits or semiconductors if you touch bus connector

pins. Follow these guidelines when you handle the

module:

•Touch a grounded object to discharge static

potential.

•Wear an approved wrist-strap grounding

device.

•Do not touch connectors or pins on

component boards.

•Do not touch circuit components inside the

module.

•If available, use a static-safe work station.

•When not in use, keep the module in its

static-shield box.

To comply with the CE Low Voltage Directive (LVD),

all connected I/O must be powered from a source

compliant with the following: Safety Extra Low

Voltage (SELV) or Protected Extra Low Voltage

(PELV).

Micro800™ 4 Ch Universal Analog Input Module 4

Publication 0100189-04 Rev. C

Parts List

Your package contains one Micro800 Universal Analog Input Plug-in

Module and one Quick Start guide.

You can choose to wire the plug-in before inserting it onto the controller,

or wire it once the module is secured in place.

•This equipment is considered Group 1, Class

A industrial equipment according to

IEC/CISPR 11. Without appropriate

precautions, there may be difficulties with

electromagnetic compatibility in residential

and other environments due to conducted

and radiated disturbance.

•Be careful when stripping wires. Wire

fragments that fall into the controller could

cause damage. Once wiring is complete,

make sure the controller is free of all metal

fragments before removing the protective

debris strip.

•Do not wire more than 2 conductors on any

single terminal.

•If you insert or remove the plug-in module

while power is on, an electrical arc can

occur. This could cause an explosion in

hazardous location installations. Be sure that

power is removed or the area is

nonhazardous before proceeding.

•Cable length should be less than 10 meters.

•Do not insert or remove the plug-in module

while power is applied, otherwise, permanent

damage to equipment may occur.

Micro800™ 4 Ch Universal Analog Input Module 5

Publication 0100189-04 Rev. C

Insert Module into Controller

Follow the instructions to insert and secure the plug-in module to the

controller.

1. Position the plug-in module with the terminal block facing the

front of the controller as shown.

2. Snap the module into the module bay.

3. Using a screwdriver, tighten the 10…12 mm (0.39…0.47 in.) M3

self-tapping screw to torque specifications.

Micro800™ 4 Ch Universal Analog Input Module 6

Publication 0100189-04 Rev. C

IN +2

IN -2

IRET2

IN +3

IN -3

IRET3

IN +0

IN -0

IRET0

IN +1

IN -1

IRET1

+ -

2 wire

XMTR

24 Vdc

Pwr

2-wire RTD/Resistance

Current Input

Voltage Input

Thermocouple Input

IN +2

IN -2

IRET2

IN +3

IN -3

IRET3

IN +0

IN -0

IRET0

IN +1

IN -1

IRET1

3-wire RTD

4-wire RTD

Wire the Module

Follow the wiring diagrams below to wire the module.

Configuring the Module

The 2080sc-IF4U is configured using 8 SINT configuration registers.

The following table describes the module configuration registers.

Table 1 (Configuration Assembly)

Bits

MSB

LSB

Ch0

Config.

Bytes

Channel

Enable

Disable

Filter Frequency

17 Hz

4 Hz

60 Hz

240 Hz

470 Hz

Input Type

4-20 mA

0-20 mA

+/-10 V

0-10 V

0-5 V

+/-100 mV

+/-50 mV

Type J TC

Type K TC

Micro800™ 4 Ch Universal Analog Input Module 7

Publication 0100189-04 Rev. C

Bits

MSB

LSB

Type T TC

Type E TC

100 Pt 385

1000 Pt 385

100 Pt 3916

1000 Pt

3916

0-3000

Ohms

Type R TC2

Undefined Bits

Data Format1

Engr. X1

Engr. X10

Temp. Units

Degrees C

Degrees F

2/3/4 Wire RTD, ignored for

R ranges.

3 Wire

(Default)

4 wire with

lead

2 wire

CJC enable

Enable

Disable

Ch1

Config.

Bytes

Data structure the same as channel 0 above

Ch2

Config.

Bytes

Data structure the same as channel 0 above

Ch3

Config.

Bytes

Data structure the same as channel 0 above

1See Table 2 (Data Format)

2Type R thermocouple is only available on modules running firmware version 1.3 or higher.

Table 2 (Data Format)

Input Type

Input Value

Condition

EU x1

EU x10

E Thermocouple

1000.00 deg C

High Range

10000

1000

-270.00 deg C

Low Range

-2700

-270

J Thermocouple

1200.00 deg C

High Range

12000

1200

-210.00 deg C

Low Range

-2100

-210

K Thermocouple

1370.00 deg C

High Range

13700

1370

-270.00 deg C

Low Range

-2700

-270

Micro800™ 4 Ch Universal Analog Input Module 8

Publication 0100189-04 Rev. C

Input Type

Input Value

Condition

EU x1

EU x10

T Thermocouple

400.00 deg C

High Range

4000

400

-270.00 deg C

Low Range

-2700

-270

R Thermocouple

1768.00 deg C

High Range

17680

1768

0.00 deg C

Low Range

100 Ohm Pt 0.385

850.00 deg C

High Range

8500

850

-200.00 deg C

Low Range

-2000

-200

1000 Ohm Pt 0.385

850.00 deg C

High Range

8500

850

-200.00 deg C

Low Range

-2000

-200

100 Ohm Pt 0.392

630.00 deg C

High Range

6300

630

-200.00 deg C

Low Range

-2000

-200

1000 Ohm Pt 0.392

630.00 deg C

High Range

6300

630

-200.00 deg C

Low Range

-2000

-200

0..3000 Ohms

3000.00 ohms

High Range

30000

3000

0.00 ohms

Low Range

+/-50mV

50.00 mV dc

High Range

5000

500

-50.00 mV dc

Low Range

-5000

-500

+-100mV

100.00 mV dc

High Range

10000

1000

-100.00 mV dc

Low Range

-10000

-1000

0..5V

5.00 V dc

High Range

5000

500

0.00 V dc

Low Range

+/-10V

10.00 V dc

High Range

10000

1000

-10.00 V dc

Low Range

-10000

-1000

0..10V

10.00 V dc

High Range

10000

1000

0.00 V dc

Low Range

4..20mA

20.00 mA

High Range

20000

2000

4.00 mA

Low Range

4000

400

0..20mA

20.00 mA

High Range

20000

2000

0.00 mA

Low Range

CJC

85.00 deg C

High Range

850

-25.00 deg C

Low Range

-250

-25

Micro800™ 4 Ch Universal Analog Input Module 9

Publication 0100189-04 Rev. C

Module Input Data

There are four input registers used to report data values for each of the

four channels and one register to report CJC sensor temperature.

Table 3 (Module Input Data)

Bit

Ch0

Channel 0 Input Data

Ch1

Channel 1 Input Data

Ch2

Channel 2 Input Data

Ch3

Channel 3 Input Data

CJC

CJC Temperature in degrees C

Three separate status bytes are available to the user, one for open-

circuit detect, one for over/under range detection, and one for general

module status.

Table 4 (Open-circuit Status)

Bit

O_CJC

U_CJC

OC3

OC2

OC1

OC0

Bit 0 for channel 0 open wire.

Bit 1 for channel 1 open wire.

Bit 2 for channel 2 open wire.

Bit 3 for channel 3 open wire.

Bit 4 is for CJC under range indication.

Bit 5 is for CJC over range indication.

Bit 6 and Bit 7 are not used.

Micro800™ 4 Ch Universal Analog Input Module 10

Publication 0100189-04 Rev. C

Table 5 (Under/Over Range Status)

Bit

Bit 0 is for channel 0 under range indication

Bit 1 is for channel 1 under range indication

Bit 2 is for channel 2 under range indication

Bit 3 is for channel 3 under range indication

Bit 4 is for channel 0 over range indication

Bit 5 is for channel 1 over range indication

Bit 6 is for channel 2 over range indication

Bit 7 is for channel 3 over range indication

Table 6 (General Module Status)

Bit

Number

Description

Notes

0-1

These 2 bits define module

operation mode,

0: Idle: Module is ready to RUN,

and I/O is off.

1: RUN: Module is under RUN,

and I/O is on.

2: Error: Error happens, and I/O is

off.

3: Busy: Module is busy, cannot go

to RUN, and I/O is off.

This bit defines module user

interrupt mode,

0: User Interrupt is disabled.

1: User Interrupt is enabled.

The IF4U does not support this

functionality; this bit is always off (0).

Reserved

SW Error

Trigger condition –Watchdog timer

triggered.

ADC Error

Trigger condition –ADC

communication stops or ADC has not

sampled data for long period of time.

Calibration Error

Trigger condition –blank calibration or

calibration checksum error.

Configuration Error

Wrong bits set in channel

configuration.

Tabla de contenidos

Otros manuales de Unidad de control de Spectrum Controls

Spectrum Controls

Spectrum Controls 1756-CTR8 Manual de usuario

Spectrum Controls

Spectrum Controls 1794sc-IRT8I Manual de usuario

Spectrum Controls

Spectrum Controls SLC 500 Manual de usuario

Spectrum Controls

Spectrum Controls 2085sc-IF8U Manual de usuario

Spectrum Controls

Spectrum Controls Micro800 2085-IR8-SC Manual de usuario

Spectrum Controls

Spectrum Controls Micro800 2085-IF16C-SC Manual de usuario

Spectrum Controls

Spectrum Controls DTAM PLUS 2707-L40 Series Manual de usuario

Spectrum Controls

Spectrum Controls 1794 Manual de usuario

Spectrum Controls

Spectrum Controls 1762sc-IF4OF4 Manual de usuario

Spectrum Controls

Spectrum Controls SLC 500 Manual de usuario

Spectrum Controls

Spectrum Controls Micro 800 Manual de usuario

Spectrum Controls

Spectrum Controls Micro800 2085-IR8-SC Manual de usuario

Spectrum Controls

Spectrum Controls SLC 500 1746sc-INO4i Manual de usuario

Spectrum Controls

Spectrum Controls 1762sc-OF8 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario