SpectraPure Mega MaxCap Manual de usuario

REV_3 2017-10-25

INSTALLATION AND OPERATING MANUAL

WARNING

Please read carefully before proceeding with installation. Failure to

follow any attached instructions or operating parameters may lead

to the product’s failure and possible damage to property.

Mega MaxCap®(manual flush)

Single (90 gpd) or Dual (180 gpd) Membrane Models

Reverse Osmosis/Deionization

Water Purification Systems

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

TABLE OF CONTENTS:

System Information

System Features 3

System Specifications 4

General System Description 5-6

Flow Restrictors And Test Strips 7

Optional Booster Pump 7

Front View Of System 8

Top Views Of System 9

Manual Flush Assembly 9

System Setup

Cautions 10

System Installation And Initialization 10 -11

Float Valve Installation 11

Float Valve Illustration 12

HowThe Float Valve Works 12

System Diagnostics

Metering And Diagnostics 13

Using The Pressure Gauge 14

Using The Manual Flush Valve 14

Testing The Quality Of The Membrane 15

Membrane Production Calculation 16 -17

Tips For Long Membrane Life 17

System Maintenance

Working With Push Fittings 18

Sediment Prefilter Replacement 19

Carbon Block Filter Replacement 20

Mega MaxCap Super DI Replacement 21

SilicaBuster Super DI Replacement 21

RO Membrane Replacement 22

Sanitizing The System 23

System Storage 23

System Troubleshooting Guide 24-25

Optional Accessories 25

Terms And Conditions 26

Three-Year Limited Warranty 27

Replacement Parts And Accessories 28

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photocopying,

recording or otherwise without the prior written permission of SpectraPure Inc.

SpectraPure

Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

[email protected] www.spectrapure.com 3

SpectraPure

Thank You for your purchase of a SpectraPure®System. With proper installation

and maintenance, this system will provide you with high quality water for

years to come. All SpectraPure®products are rigorously tested by us for

safety and reliability. However, SpectraPure®Inc. Assumes No Responsibility

for water damage due to leaks. It is the user’s responsibility to determine that

the system is leak-free. If you have any questions or concerns, please contact

our customer service department at 1.800.685.2783.

This Mega MaxCap™RO/DI System comes complete with:

• Ultra-high rejection SpectraSelectPlus™ TFC Membrane

(2 membranes in 180GPD system)

• 0.5 micron High-Performance Sediment prefilter

• High-capacity 0.5 micron Carbon Block prefilter eliminates chlorine,

herbicides and other organic pollutants

• Newly-designed Mega MaxCap™ DI Cartridge (DI-MMC-10) with

greatly improved removal capacity

• New Enduro DI™ Finishing Cartridge (DI-MB-ENDI-10)

• Two dual-probe TDS Meters to monitor performance at every stage

of production

• 2:1 waste-to-product ratio produces 50% less waste water

(3:1 for hard water areas)

• Manual Flush Valve for longer membrane life

• Automatic Shutoff Valve saves water

• Inline feedwater Ball Valve for manual system shutoff

• Float Valve for filling a reservoir

• Built-in pressure gauge indicates when to change prefilters

• Durable, no rust mounting bracket and clear filter housings

• 6 feet of feed, product and waste tubing included

• Housing wrench for easy filter removal

• Garden hose adapter for feed water hookup

• 3-year warranty

Warning: SpectraPure does not recommend

drinking deionized water.

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

SYSTEM SPECIFICATIONS:

Sediment Prefilter 0.5 micron sediment prefilter (SF-MT-0.5-10)

Carbon Filter 0.5 micron carbon block prefilter (CF-0.5-10)

RO Membrane Type 90 GPD SpectraSelectPlus™ TFC Membrane

(Use 2 for 180 GPD Systems)

DI Cartridges Mega MaxCap™ Extended Life DI Cartridge (DI-MMC-10)

Enduro DI™ DI Finishing Cartridge (DI-MB-ENDI-10)

Rejection Rate Typical stabilized conductivity rejection 99%

Minimum conductivity rejection 98%

Input Water Pressure 60 psi (4.15 bar) line pressure*

Input Water Temp 77°F (25°C)

Recovery Rate 33% (i.e. 33% of the water will be collected as pure water)

Dimensions:

MMC-RODI-90-10-MF 21" W x 15" H x 7" D (One Membrane)

MMC-RODI-180-10-MF 21" W x 15" H x 7" D (Two Membranes)

Nominal Membrane Flow Rates @ 60 psi, 77° F, & 250 ppm TDS :

GPD Product Water Flow Rate Concentrate Flow Rate (2:1)

90 237 ml/min 473 ml/min

180 473 ml/min 946 ml/min

Permeate flow and TDS rejection is based on the following test conditions:

250 ppm softened tap water, 77° F (25° C), 33% recovery and 60 psi.

Higher TDS, harder tap water, lower water temperature, greater recovery rate, or lower

operating pressure may contribute to reduced permeate flow and/or lower TDS rejection.

Reverse Osmosis Operating Limits:

Operating Pressure* 40 – 80 psi (2.75 – 5.5 bar)

pH Range 2 –11

Maximum Temperature 113° F (45° C)

Maximum Turbidity 1.0 NTU

Maximum Silt Density Index 5.0 (based on 15 min. test time)

Free Chlorine Tolerance less than 0.1 ppm

Maximum Iron less than 0.1 ppm

Maximum Manganese less than 0.1 ppm

Maximum Hydrogen Sulfide 0 ppm

*Operating pressure less than 40 psi may require a booster pump:

Operating pressure greater than 80 psi may require a pressure regulator.

SpectraPure

Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

[email protected] www.spectrapure.com 5

SpectraPure

GENERAL SYSTEM DESCRIPTION:

The incoming feed water from a cold water source is directed through

BLACK tubing with an inline ball valve and is first passed through a

sediment prefilter. This filter is used to remove excessive turbidity, sand,

dust, silt, etc., that would otherwise cause the carbon filter to become

fouled. The next stage of filtration is the carbon block prefilter. This filter

is used to remove organics and chlorine from the feed water that can

damage the membrane. The next stage of the system is the RO membrane.

Household water pressure is used to force tap water through the

semipermeable RO membrane. The membrane only allows the purest of

water molecules to pass through it while over 98% of

most inorganic salts,

all microorganisms and almost all high molecular weight organics in the

water

are rejected by the membrane and sent down the drain.

These RODI systems have two stages of Deionization that polish the RO

water to less than one ppm purity.

The fourth and fifth stage filters are our

Mega MaxCap™ DI Cartridge and our Enduro DI™ High-Performance DI

Finishing Cartridge.

The Mega MaxCap™ DI Cartridge is used as a high-capacity “roughing”

cartridge and is followed by our Enduro DI™ high-performance finishing

cartridge. The Mega MaxCap™ DI cartridge has a much higher capacity,

but less purity than the Enduro DI™ cartridge. These DI cartridges work

in tandem to achieve a greatly extended lifespan when compared to

standard mixed-bed DI cartridges. Because the RO water reaches it first,

the Mega MaxCap™ will need to be replaced more often than the Enduro

DI™.

The Mega MaxCap™RODI system comes equipped with two Dual-Probe

Inline TDS meters for complete monitoring of water purity throughout

every stage of the purification process. The left-side TDS meter will monitor

the tap water TDS and the TDS of the RO water, allowing you to accurately

compute the rejection rate of the RO membrane. (See “Testing The Quality

Of The Membrane” on Page 15.) The right-side meter monitors the DI

cartridges to let you know when they need to be replaced. It will also

monitor the purity of your product water when set to the “Out” position.

(continued on next page)

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

A pressure -operated Automatic Shutoff (ASO) Valve and a Float Valve are

provided for convenient filling of a storage reservoir.

NOTE: SpectraPure does not recommend using the Float Valve for topoff

due to evaporation. The short duration of the fill cycle when using

a float valve will rapidly deplete the life of the DI cartridges due

to TDS creep. Instead, we recommend the use of high/low float

switches in the reservoir/sump to extend the fill cycle and minimize

the effects of TDS creep. (see SpectraPure part number LLC-SVC-

2FLT-2-10)

The Manual Flush Valve may be used to periodically rinse the accumulated

impurities and concentrated waste water from the surface of the RO

membrane to help increase the life of the membrane. The Manual Flush

Valve is located in parallel with the flow restrictor (see page 9) and, when

opened, provides a high-flow bypass of waste water used to purge

concentrated brine from the membrane housing and rapidly flush any

particulates from the membrane surface. This is especially useful in hard

water conditions. We recommend that the valve be turned ON for 30

seconds at the start of a fill cycle and at the end of a fill cycle. BE SURE to

turn the Flush Valve OFF before making product water.

GENERAL SYSTEM DESCRIPTION: (continued)

SpectraPure

Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

[email protected] www.spectrapure.com 7

SpectraPure

OPTIONAL BOOSTER PUMP (BPHF-MF-115):

An optional Booster Pump is necessary for installations with less than 40

psi tap water pressure.

RO production is directly dependent upon water pressure, so the

production rate may be dramatically increased by adding a Booster

Pump Kit. When installed between the Carbon Block filter and the RO

Membrane, the pressure may be increased up to 80 psi.This would double

the production rate if the starting household water pressure is 40 psi.

Higher water pressure not only increases the rate of production, it also

results in higher rejection rates for the RO Membrane. Higher rejection

rates mean less contaminants reach the DI stages, thereby extending the

life of your DI Cartridges which are a more expensive way to filter water

when compared to Reverse Osmosis Membranes.

If you are interested in installing a Booster Pump Kit on your RO/DI system

or if you have any questions regarding a Booster Pump Kit, please contact

SpectraPure Support.

FLOW RESTRICTORS AND TEST STRIPS:

These systems are supplied with TWO Flow Restrictors (FR) - RED and

GREEN. (See images on Page 9.) The RED FR (pre-installed) produces a

preset waste-to-product ratio of 3:1 and the optional GREEN FR has a 2:1

ratio.

Two Test Strips are provided to determine the Total Hardness (this is NOT

TDS) of your tap water. To test: Dip the colored end into a small tap water

sample for 3 seconds. Remove and do not shake. Wait for 20 seconds and

then match with the closest color block on the back of the package. Color

is stable for 1 minute.

If the Total Hardness is 180 or greater, you should keep the RED FR installed.

If the Total Hardness is less than 180, you may replace the RED FR with the

GREEN FR. (see “Working with Push Fittings” on Page 18.) Be sure to note

the orientation of the small “plug” in the end of the removed FR and install

the new FR with the same orientation.

The RED FR has a waste-to-product ratio of 3:1, which will increase the

amount of water used, but also increase the lifetime of the RO membrane.

In hard water conditions, you may use the GREEN FR to save water, but

the RO membrane will not last as long, as it will plug up with hardness

much more quickly.

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

SpectraSelectPlus™ 90 GPD

Membrane (inside housing)

Left-side Meter

“IN” = Tap Water TDS

“OUT” = RO Water TDS

Right-side Meter

“IN” = MaxCap DI TDS

“OUT” = Enduro DI TDS

Pressure Gauge

Manual Flush Valve

0.5 micron

Sediment Prefilter

(SF-MT-0.5-10)

1/4" BLACK

Tap Water

Tubing

Attaches

Here

0.5 micron

Carbon Block Filter

(CF-0.5-10)

Mega MaxCap™

DI Cartridge

(DI-MMC-10)

Enduro DI™

Finishing Cartridge

(DI-MB-ENDI-10)

MAXCAP®MMC- RODI-90-10-MF : Front View

(180 GPD system is the same except for extra membrane housing)

SpectraPure

Inc

. Fax 480.894.6109 Fax us toll-free 1.877.527.7873

[email protected] www.spectrapure.com 9

SpectraPure

MEGA MAXCAP™RO/DI Systems : Top Views

“IN” Port of ASO Valve

Flow Restrictor located

inside this end of Red

(or Green) Tubing

Automatic ShutOff

(ASO) Valve

1/4" Yellow

Tubing to

Drain

Handle in “RUN” position. If handle is parallel to tubing, system is in “FLUSH” mode.

“OUT” Port of ASO Valve

MANUAL FLUSH ASSEMBLY

REAR

FRONT

Flow Restrictor located

inside this end of Red

(or Green) Tubing

Automatic ShutOff

(ASO) Valve

1/4" Yellow

Tubing to

Drain

REAR

FRONT

1/4" Yellow

Tubing to

Drain

90 GPD Single-Membrane System

180 GPD Dual-Membrane System

SpectraPure

Inc.

480.894.5437 Call us toll-free 1.800.685.2783

2167 East Fifth St, Tempe, Arizona 85281

SYSTEM INSTALLATION & INITIALIZATION:

1. Attach the black tap water tubing to the left side of the Sediment Filter Housing

(See page 8).

2. Attach the yellow drain line to the “Y”- connector at the rear of the system. This “Y”

-connector already has a yellow and red tube attached to it. (See page 9)

3. Attach the blue product line to the rear port of the

right-hand DI housing (Left-side housing when

viewed from rear. See image on right).

4. Attach the black tubing and elbow(s) to the

membrane housing cap(s). (See page 9)

5. Attach the garden hose adapter (connected to

the black tubing) to your cold water source.

6. Remove the two DI filter cartridges from the two right-hand filter housings.

Reconnect the two housings to their threaded caps. Hand tighten.

7. The provided ball valve can be located at a convenient place on the black tap

water line. Cut the black tubing in two and reconnect the two cut ends with

the ball valve. This will allow you to cut off the water supply to service the RO/

DI system without affecting the household water supply.

8. Place the yellow concentrate (waste) tubing and the blue purified (product)

water tubing temporarily into a drain. Do not restrict flow from these lines.

9. Let both tubings run water down the drain for 20 minutes.

10. Reinstall the two DI cartridges into the DI housings. Hand tighten.

(continued on next page)

• Most of the components of this system are plastic and are subject to damage

by ultraviolet light from the sun and other sources such as metal halide

lighting.

• Avoid installing this unit in an area where it may be subjected to bright

light or direct sunlight, as algae is more likely to thrive inside the clear filter

housings when exposed to bright light. The unit must be kept out of

areas that are subject to freezing temperatures.

• High temperatures greater than 113° F (45° C) must be avoided. If the unit

is used outside, avoid putting the system in direct sunlight or connecting

it to a garden hose that may be exposed to sunlight.

CAUTION

Tabla de contenidos

Otros manuales de Sistema de filtración de agua de SpectraPure

SpectraPure

SpectraPure The Ultimate DI System Manual de usuario

SpectraPure

SpectraPure MaxPure MPRO-300 RO System Manual de usuario

SpectraPure

SpectraPure Coffee Lovers System CLS-90 Manual de usuario

SpectraPure

SpectraPure MAXCAP RO/DI Manual de usuario

SpectraPure

SpectraPure MPRO RO System Manual de usuario

SpectraPure

SpectraPure MAXCAP RO Manual de usuario

SpectraPure

SpectraPure PERFORMANCE PLUS MC-RODI-100-PPLUS Instrucciones originales

SpectraPure

SpectraPure CSPDI-90-MF Manual de usuario

SpectraPure

SpectraPure MC-RODI-200UHE Instrucciones originales

SpectraPure

SpectraPure MaxCap MC-RODI-90-10-MF Manual de usuario

SpectraPure

SpectraPure SpectraPlus 2000 Manual de usuario

SpectraPure

SpectraPure PROPLUS RO System Manual de usuario

SpectraPure

SpectraPure PSP-600 Manual de usuario

SpectraPure

SpectraPure The Eliminator RO System Manual de usuario

SpectraPure

SpectraPure CSP Series Manual de usuario

SpectraPure

SpectraPure SP-RO-90 RO BASIC Manual de usuario

SpectraPure

SpectraPure Coffee Lovers System CLS-5-90 Manual de usuario

SpectraPure

SpectraPure The Eliminator Manual de usuario

SpectraPure

SpectraPure MaxCap MC-RODI-180-MF Manual de usuario

SpectraPure

SpectraPure CSPDI-180 Manual de usuario

SpectraPure

SpectraPure Eliminator 90 Manual de usuario

SpectraPure

SpectraPure 100 GPD U.H.E RO/DI Instrucciones originales

SpectraPure

SpectraPure The MarinePRO Manual de usuario

SpectraPure

SpectraPure PSP Series Manual de usuario

Manuales populares de Sistema de filtración de agua de otras marcas

Wisy

Wisy LineAir 100 Manual de usuario

Schaffner

Schaffner Ecosine FN3446 Series Manual de funcionamiento

Pentair

Pentair FLECK 4600 SXT Guía del usuario

H2O International

H2O International H20-500 Manual de usuario

Renkforce

Renkforce 2306241 Manual de usuario

Neo-Pure

Neo-Pure TL3-A502 Manual de usuario

FLTR

FLTR OBF Manual de usuario

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manual de usuario

Applied Membranes

Applied Membranes W-G844EM Manual de usuario

BEGA

BEGA 116 Manual de usuario

WATA

WATA Standard Manual de usuario

Price

Price FFU series Manual

Gaggenau

Gaggenau BRITA INTENZA 467873 Manual de usuario

Brita

Brita SAFF-100 Manual de usuario

HEISSNER

HEISSNER FPU24000-00 Manual de usuario

BGS technic

BGS technic 1518 Manual de usuario

Reverse Osmosis

Reverse Osmosis RF Series Manual de usuario

ubbink

ubbink Filtramax Series Manual de usuario