Speco O5P2 Manual de usuario
Quick Start Guide
O5P2
Welcome
Thank you for purchasing this network camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time;
it may result in device damage! The product must be grounded to reduce the risk of
electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation,
storage and installation.
This product should be installed in a cool, dry place away from direct sunlight and heat
sources.
Do not install the product in extreme temperature conditions.
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS
sensor failure.
Do not block any ventilation openings.
Do not allow water and liquid intrusion into the camera.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning
Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Dome cover is an optical device, please don't touch or wipe cover surface directly during
installation and use, please refer to the following methods if dirt is found:
Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently.
Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked with alcohol
or detergent to wipe from the lens center outward. Change the cloth and wipe several
times if it is not clean enough.
Package
1
Overview
3 Overview
2
Ethernet connector
Reset
Micro SD card slot
Audio input connector
DC power connector
1
2
6
5
3
4
Camera Quick start guide
CD Plastic plug ×2
Drill template Wall mounting bracket
Screwdriver
2 tapping screws PA 4×25
5
6
1
2
3
4
Microphone
* 1 It is recommended to install the security cap for outdoor installations.
* 2 DC 12V power supply is not required if a PoE switch or injector is used to power
the camera.
► Connecting Network Cable
① Loosen the nut from the main element.
② Run the network cable (without RJ 45 connector) through both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut
and the main cover.
2
13
Security Cap
DC12V
Installation
3
* Before you start, please make sure that the wall or ceiling is strong enough
to withstand three times the weight of the camera and bracket.
① Loosen the lock screw of the bracket and then remove the
mounting base from the bracket.
② Loosen the screws to remove the lower dome from the camera.
Lower Dome
Lock screw
Mounting base
③fix the camera onto the
bracket with the screws provided.
Pull the cables through the bracket. Then
④Fix the mounting base of the bracket onto the wall with the screws.
⑥
preview the image of the camera on a monitor.
Adjust the camera to obtain an optimum angle . Before adjustment,
⑤
base and fasten them with the lock screw.
Connect the cables. Then attach the bracket onto the mounting
Rotation 0°~350°
Pan 0°~360°
Tilt 0°~70°
Web Operation and Login
4
●Operation
IP Scanner can search for the device on the local network.
①Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
②Install IP Scanner from the CD and run it after installation. Or
download from https://www.specotech.com/ip-scanner/
⑦Install the lower dome back to the camera with the screws.
③In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.
O5 P2
5C :F 2:07:25 :6 8: 9A
Tabla de contenidos
Otros manuales de Cámara de seguridad de Speco
Speco
Speco ONSIP OD8 Manual de usuario
Speco
Speco CVC-635CR Manual de usuario
Speco
Speco HT-7715DNV Manual de usuario
Speco
Speco O4LT1M Manual de usuario
Speco
Speco VLB11SCSFF Manual de usuario
Speco
Speco CVC605CMT Manual de usuario
Speco
Speco INTENSIFIER CVC6246IHR Manual de usuario
Speco
Speco 700Line IntensifierH CVC6246H Manual de usuario
Speco
Speco O4iB2 Manual de usuario
Speco
Speco HTINT40T1 Manual de usuario
Speco
Speco CVC-637EX Manual de usuario
Speco
Speco O8FT1W Manual de usuario
Speco
Speco LPRD922 Manual de usuario
Speco
Speco HT - INTB8/9/10 Manual de usuario
Speco
Speco ProVideo CVC-7005EXTP Manual de usuario
Speco
Speco HT66iLHB Manual de usuario
Speco
Speco O4VLD1 Manual de usuario
Speco
Speco ProVideo CVC-7700DN Manual de usuario
Speco
Speco O8D7M Manual de usuario
Speco
Speco HT-INTB1 Manual de usuario
