Speco O2BLP1M Manual de usuario

Quick Start Guide

O2BLP1M

1Warning and Caution

Package

Overview

3 Overview

Camera Quick start guide

CD Plastic plug ×4

Drill template

Screwdriver Junction box

4 tapping screws

1 machine screw

* 1

* 2 If the PoE switch is used to power the camera, DC12V power supply is not required.

It is recommended to install the security cap for outdoor installation.

1 Ethernet Connector

2 MIC-Audio Input

3 HP-Audio Output

4 Alarm Output/Input

5 Power Connector *

6 Micro SD Card Slot

7 Zoom +*

8 Zoom -*

9 CVBS output (unavailable)

10 Reset

ALARM

4 3 2 1

* 1 It is recommended to install the security cap for outdoor installations.

* 2 DC 12V power supply is not required if a PoE switch or injector is used to power

the camera.

► Connecting Network Cable

① Loosen the nut from the main element.

② Run the network cable (without RJ 45 connector) through both elements.

Then crimp the cable with RJ 45 connector.

③ Connect the cable to the hermetic connector. Then tighten the nut and the

main cover.

1--ALM-COM

2--ALM-OPEN

3--ALM-INA

4--ALM-GND

Security cap

DC12V

ALARM

4 3 2 1

Installation

* Before you start, please make sure that the wall or ceiling is strong enough

to withstand three times the weight of the camera and junction box.

①Open the mounting base and the upper cover of the junction box.

SD Card Installation

Camera Installation with a Junction Box

Insert a micro

SD card

Cover

Open the cover of the camera as shown in the following figure and then insert

a micro SD card. After that, install the cover back to the camera (Note that the

cover shouldn’t be installed unevenly).

Mounting base

Upper cover

② Install the mounting base of the junction box onto the wall by using the

screws provided.

③Fix the mounting base of the camera to the upper cover of the junction

box.

④ Route the cables through the cable hole and connect the camera. Then install

the camera onto the mounting base of the junction box.

Three-axis Adjustment-Before adjustment, preview the image of the camera

on a monitor and then loosen the fixed screws to adjust the camera according to

the figure below to get an optimum angle.

⑤

Tilt 90°

Pan 360°

Rotate

360°

Fixed screws

The monitoring image shall try to cover the lane, entering/exiting vehicles

and these vehicles' plate number shall be always seen in the video.

Try to avoid the objects that will block the camera, such as pillars,

obstacles, doors, etc.

Avoid the scenes with many trees or other moving objects (like humans,

non-motor vehicles).

The monitoring road shall be straight within 165ft in front of/behind the

location of the camera installation and make sure the camera points at the

front or rear of the vehicle.

Overhead Monitoring

The installation height (H) shall range from 15 ~ 20ft.

The distance D (between the location of the camera installation and the

captured area) shall range from 50 ~ 82ft. This distance (D) depends on the

installation height, usually 3 or 4 times as far as the installation height (H).

The distance of the captured area (L) shall be from 50 ~ 65ft.

Configuration requirements of camera and surrounding area

Note: The following installation requirements are based on optimum conditions,

your license capture rate may vary depending on speed, lighting, position, license

plate designs and other factors.

The depression angle of the camera shall range from 10° to 15°.

If the camera is installed on the side of the road, the pan angle of the camera

shall range from 0° to 20°.

If the camera is installed right above the middle of the road, the pan angle

of the camera shall range from -10° to 10°.

Entrance & Exit Monitoring

The installation height (H) shall range from 4.2ft to 5ft.

The distance D (between the location of the camera installation and the

captured area) shall range from 8.2ft to 10ft.

The distance of the captured area (L) shall be from 5ft to 6.5ft.

50~65 feet 50~82 feet

15~20feet

H4.2~5ft

8.2~10ft

5~6.5ft

<40MPH

The depression angle of the camera shall range from 0° to 5°.

The pan angle of the camera shall range from 5° to 20°.

If the captured license plate doesn't meet the above requirement, you can

adjust the pan angle of the camera to correct it.

The tilt angle of the license plate

After the camera is installed, you can log in the web client and view

whether the license plate tilts in the video. The tilt angle shall range from

-5° to 5°.

Web Operation and Login

Operation

IP Scanner can search for the device on the local network.

①Make sure that the camera and the PC are connected to the same local network.

The camera is set to DHCP by default.

② Install IP Scanner from the CD and run it after installation.

●

The login interface is shown above. Default user name is admin and password

is 1234. After logging in, follow directions to install applicable plugins.

③ In the device list, you can view the IP address, model number, and MAC

address of each device. Select the applicable device and double click to open

up the web viewer. You can also manually enter the IP address in the address

bar of the web browser.

O2BL P1M 5 2C:F2:07 :4:68:9A n/a n/a

192.1 68.17.2 51

Tabla de contenidos

Otros manuales de Cámara de seguridad de Speco

Speco

Speco HT-647HRTP Manual de usuario

Speco

Speco CVC5845DNV Manual de usuario

Speco

Speco H4FB1 Manual de usuario

Speco

Speco ONSIP 02S1 Manual de usuario

Speco

Speco ProVideo CVC-870EX Manual de usuario

Speco

Speco O2VT1V Manual de usuario

Speco

Speco O2P25X Manual de usuario

Speco

Speco O4BLP2M Manual de usuario

Speco

Speco HT-7246IHR Manual de usuario

Speco

Speco VLEDT2HG Manual de usuario

Speco

Speco VL12 Manual de usuario

Speco

Speco WDR-R3 Manual de usuario

Speco

Speco INTENSIFIER3 HT647HRTP Manual de usuario

Speco

Speco O8B9M Manual de usuario

Speco

Speco TC-23 Manual de usuario

Speco

Speco O4iT1 Manual de usuario

Speco

Speco O4FB8M Manual de usuario

Speco

Speco INTENSIFIER3 HTINTB10 Manual de usuario

Speco

Speco O4LB1 Manual de usuario

Speco

Speco O5D4M Manual de usuario

Speco

Speco O4iT2 Manual de usuario

Speco

Speco VLB11SCSFF Manual de usuario

Speco

Speco ONSIP O2B5 Manual de usuario

Speco

Speco CVC5845DNV Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario