INSTALLATION INSTRUCTIONS
-05--04-
WARRANTY INFORMATION
Our company warranties its products to be free of defects in materials and workman-
-ship for a period of two (2) years. There are no obligations or liabilites on the part
use or performance of this product or other indirect damages with respect to loss
of property, revenue, or profit, or cost of removal, installation or reinstallation.
of our company for consequential damages arising out of or in connection with the
Jun,2011
Restoring Factory Defaults
All Configuration Parameters can all be restored to their factory default settings by
using your primary controller to delete/reset the device.
-06-
Refer to the instructions for your primary controller to access the network setup
function and include or exclude devices.
When prompted by your primary controller, tap the top or bottom of the paddle.
The primary controller should indicate that the action was successful. If the
controller indicates the action was unsuccessful, please repeat the procedure.
Once the switch is part of the network, the same basic procedure is used to add
the switch to groups & scenes or change advanced functions. Refer to the primary
controller’s instuctions for details.
Please Note: After a power failure, the ZW15S switch returns to
the last used state.
ADVANCED OPERATION
The following Advanced Operation parameters require that you have an advanced
controller. However, basic remotes do not have this capability.
All-ON and All-OFF
Depending upon your primary controller, the ZW15S switch can be set to respond to
ALL-ON and ALL-OFF commands in up to four different ways.Some controllers may
not be able to change the response from its default setting. Please refer to your
controller’s instructions for information on whether or not it supports the configuration
function and if so, how to change this setting.
The four possible responses are:
- It will respond to ALL-ON and the ALL-OFF command (default).
- It will not respond to ALL-ON or ALL-OFF commands.
- It will respond to the ALL-OFF command but will not respond to the ALL-ON command.
- It will respond to the ALL-ON command but will not respond to the ALL-OFF command.
From the Remote (or repeating Z-Wave module) to
destination device:
Type of
Construction
Wood Frame with
Drywall
Brick, Tile or
Concrete
Plastic
J-Boxes*
Metal
J-Boxes
Plastic
J-Boxes*
Metal
J-Boxes
Number of
Walls or
Obstacles
0** 100’ 80’ 100’ 80’
1 70’ 56’ 60’ 48’
2 49’ 39’ 36’ 29’
3 34’ 27’ 21’ 17’
Z-Wave Enabled Devices.
WIRELESS RANGE
This device complies with the Z-Wave standard of open-air, line of sight transmission
distances of 65 feet. Actual performance in a home depends on the numbers of walls
between the remote controller and the destination device, the type of contruction and
the number of Z-Wave enabled devices installed in the control network. Most Z-Wave
enabled devices act as signal repeater and multiple devices result in more possible
transmission routes which helps eliminate " RF dead-spots."
Z-WAVENETWORK
WAVENETWOR
Things to consider regarding RF range:
- Each wall or obstacle (i.e.:refrigerator, big screen TV, etc.)between the remote or
Z-Wave device and the destination device will reduce the maximum range of 100
feet by approximately 25-30%.
- Brick, tile or concrete walls block more of the RF signal than walls made of wooden
studs and plasterboard (drywall).
- Wall mounted Z-Wave devices installed in metal junction boxes may suffer a
significant loss of range (approximately 20%) since the metal box blocks a
large part of the RF signal.
Effects of Home Construction on Wireless Range Between
The distances shown in the table below are typical examples.Actual
performance in your home will vary .
Note:
Basic Operation
Remote Control
Z-Wave remotes provide control of an Individual device,Groups of devices and Scenes.
Other brands of Z-Wave Certified remotes may not offer as much flexibility in how you
can set up your lighting control network. Please refer to your remote control's instruc-
-tions for details on its capabilities and instructions for adding and controlling devices.
OPERATIONS
Air Gap Switch
LED Light
Manual Control
The switch paddle on the ZW15S allows the user to:
Turn ON/OFF the connected lighting.
To turn the connected lighting ON: Tap the top of the switch paddle.
To turn the connected lighting OFF: Tap the bottom of the switch paddle.
Switch Paddle
Air Gap Switch
The ZW15S has an air gap switch on the lower right side (see diagram for location)
to completely disconnect power to the load. Pull the air gap switch OUT to disconnect
the power while replacing light bulbs and push it all the way back in for normal
operation. The air gap switch must be all the way in for the switch to function and
control the lighting.
switch. The signals tell the Z-wave switch what action to perform.
b. Ground.
c. Neutral.
2. DO NOT connect the ZW15S-K auxiliary switch to the home’s black Hot(Line)
wire.
Once program button is pressed, the device will enter into learn mode to
accomplish inclusion or exclusion by controller.
LED Light and Buttons Configuration
By default setting ,once press button "up", the load connected to ZW15S will be
turned on,and LED light will turn off. We use Command_Class_Configuration
to configure LED light state and button toggle. After configuring,once press button
"up",the load connected to ZW15S can be turned off and LED light will be turned
off.
Configuration details
-Parameter 1 (configure LED light state ), default value is 0. Valid values are 0 and
-Parameter 2 (configure button toggle), default value is 0. Valid values are 0 and
1 with 1byte.
1 with 1byte.
The equipment has been tested and found to comply with the limits for a Class
B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment uses,generates and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction, may
cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
- This device may not cause interference
- This device must accept any interference, including interference that may
Operation is subject to the following two conditions:
cause undesired operation of the device.
FCC COMPLIANCE STATEMENT
