Speaks z wave WWA-01 Manual de usuario
WWA-01 Wireless Water & Freeze Alarm
Instruction Manual
520 Aarons Way
Ortonville, MI 48462
www.fortrezz.com
Phone: (248) 852-1307
Made in USA
Thank you for purchasing the WWA-01 Wireless Water & Freeze Alarm. This product will provide you with the peace of
mind and protection you expect. Leaking pipes, corroded water heaters, fixtures in bathrooms and laundry rooms,
refrigerator drip pans, etc. can all cause water damage. The WWA-01 is a Z-WaveTM enabled device and will send a
water leak alert on any Z-WaveTM enabled network. A WWA-01 unit that is not in a Z-WaveTM network will still alert you to
water leaks using the audio alarm.
Specifications:
Power: One 3.6V 1/2AA 1200mAh Lithium Battery, ER14250H, LS14250 or equivalent
Battery Life: Calculated to be 1 to 2 years with no alarms and default Z-WaveTM network settings.
Frequency Range: 908.42MHz (US)
Distance Range: Max 100ft line of sight in unobstructed environment
Product Size (LxWxD): 2.4" x 1.6" x 0.8"
Product Weight: 0.2 lb
Operating Temperature: -10ºC (14F) to +70ºC (158F)
Reported Temperature: Reported temperature is at the unit and has a +/- 2 degC accuracy
System Requirement: Any Z-WaveTM enabled network and controller.
Testing the WWA-01
Moisten a paper towel and place over both of the small metal pads on the water sensor until you hear the audible alarm
sound. If the audible alarm fails to sound, your battery may be old or dead or incorrectly installed, the sensor may not be
moist enough, or the water sensor may be damaged.
If you do hear the audible alarm, remove the moistened paper towel, clean the small metal pads of any water residue, and
hold the button for 2 seconds to clear the alarm. You can then add your water alarm to any Z-WaveTM enabled network
and controller. Examples of Z-Wave controllers are: Schlage LiNK, Leviton's Vizia-RF Wireless Home, and Hawking
Technologies "HomeRemote Pro Home Control”.
Using the WWA-01 in a Z-WaveTM Network
Program Switch for inclusion or exclusion
Inclusion in (adding to) a network: 1) Set up the inclusion mode at the controller; 2) Press the button (or hold the button
for approx. 2 seconds) until the controller indicates the unit has been included in the network. Also, a beep will be heard
when the inclusion completes. Inclusion and exclusion are always done at normal transmit power mode.
Exclusion from (removing from) a network: 1) Set up the exclusion mode at the controller; 2) Press the button for approx.
2 seconds until the controller indicates the unit has been removed from the network. A beep will also be heard when the
exclusion completes.
Awake Mode: To remain awake and listen for commands (when in a network), press and hold the button for at least 2
seconds. The WWA-01 will stay awake for approx. 30 seconds.
Associations: Once in a network, a controller can be used to associate the WWA-01 with other devices in the Z-WaveTM
network, such as a light or another remote audible alarm. Refer to your controller’s documentation on how to associate
the WWA-01 to another device in your network. The WWA-01 supports two association groups. A maximum of 5
associated devices are allowed in each group.
The WWA-01 sends the Basic Set Command to the associated nodes assigned to Group1 to convey that a Water
Alarm is active. If no nodes are assigned to Group 1, then an Alarm Sensor report (Sensor Type 0x05) is broadcast.
The reports are sent at regular intervals while the water alarm is active. When the water alarm is cleared via the
button, one additional report (with status = no alarm) is sent.
The button in the rear casing is used for including or excluding the WWA-01
in a Z-WaveTM network. Refer to your controller’s User Manual for specific
details on network inclusion, exclusion, and association.
520 Aarons Way
Ortonville, MI 48462
www.fortrezz.com
Phone: (248) 852-1307
Made in USA
The WWA-01 sends the Basic Set Command to the associated nodes assigned to Group2 to convey that a Freeze
Alarm is active. If no nodes are assigned to Group 2, then an Alarm Sensor report (Sensor Type 0x04) is broadcast.
The reports are sent at regular intervals while the freeze alarm is active. When the freeze alarm is cleared due to
temperature rise, one additional report (with status = no alarm) is sent.
During an alarm
If water is detected at the monitoring location, the unit will sound an 82 decibel, audible alarm and will send an alert
message to the Z-WaveTM network (if included in the network already). Pressing and holding the button for 2 seconds will
clear the Water Alarm. If freezing conditions are detected, no audible alarm will sound but an alert message is sent to the
Z-WaveTM network (if included in the network). Depending on your Z-Wave controller, it is possible to receive a remote
alert. For example, with the Hawking gateway (mentioned above), you can receive an email or cell phone text message
when the Water Alarm is active. With a gateway’s remote access to your Z-WaveTM Home Network and depending on
your specific controller’s capabilities you will be able to check the status of any WWA-01 in your network.
Choosing a mounting location
The WWA-01 is suitable for use in dry, interior locations only. Avoid placing the WWA-01 close to a metal frame, or other
metal enclosures that may affect RF range. Also, avoid areas with rapid temperature swings.
Recommended WWA-01 uses: Under sink, Next to Sump pumps, Water Heaters, Laundry Room, Bathroom Floor,
Storage Area, Garage, Utility Sink, Vacation/Recreation homes, Boats etc.
Low Battery
The WWA-01 will broadcast an alert on the Z-Wave at regular intervals when it detects a low battery condition. In
addition, it will periodically sound an audible chirp. If the chirp is heard and the battery is thought to still be good, remove
and reinsert it and wait a couple of hours. If the chirp is still heard, the battery is low or defective and should be replaced.
FCC statement
This equipment has being tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Do not dispose the WWA-01 as unsorted municipal waste; use separate collection facilities. Contact your local
government for information regarding the collection systems available.
Limited Warranty:
THE PRODUCT IS PROVIDED WITH ONE YEAR LIMITED MANUFACTURER WARRANTY. FORTREZZ, LLC.
warrants its products to be free from defects in material and workmanship under normal use for one year, and is not
responsible for consequential damages or installation costs of any nature. FORTREZZ, LLC. expressly disclaims all
implied warranties, including but not limited to the implied warranties of merchantability and fitness for a particular
purpose. FORTREZZ, LLC. does not warrant, guarantee, or make any representations regarding the use or the results of
the use of the products or any accompanying materials in terms of their correctness, accuracy, reliability or otherwise. In
no event shall FORTREZZ, LLC. be liable to Purchaser hereunder or in respect of any products ordered or delivered to
Purchaser, whether in contract, tort including negligence or otherwise for a loss of profits or loss of use or for any
incidental, consequential, special or indirect damages howsoever caused whether or not FORTREZZ, LLC. has been
advised of the possibility of such loss or damage. FORTREZZ, LLC's maximum liability to Purchaser under these
conditions shall in no event exceed the amount paid by Purchaser for the products which are the subject of the claim and
in respect of all claims for products ordered from FORTREZZ, LLC. to which these conditions apply to the amount paid by
Purchaser for the products which are the subject of the claims. If you are not comfortable with your limited warranty, or not
completely satisfied with the WWA-01, or the WWA-01 does not perform as expected we encourage you to return the
WWA-01 for a full refund within 30 days of purchase.
All products to be returned to FORTREZZ, LLC. must have a valid Returned Goods Authorization (RGA).
Send the returned unit to: FortrezZ, LLC Warranty Replacement, 3667 W. Auburn Rd. Rochester Hills, MI48309,
postage prepaid with a payment of US$ 9.95 to cover the cost of return shipping, postage and handling. You must use the
original packaging and include a proof of purchase (photocopy of receipt) along with the RGA # and the returned Wireless
Water and Freeze Alarm.
Otros manuales de Sistema de seguridad de Speaks z wave
Manuales populares de Sistema de seguridad de otras marcas
EDM
EDM Solution 6+6 Wireless-AE Manual de usuario
Highway Safety Group
Highway Safety Group EA401 Manual de usuario
Siren
Siren LED GSM Manual de usuario
Detection Systems
Detection Systems 7090i Instrucciones de montaje
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manual de usuario
Siemens
Siemens FDM273 Manual de usuario