Sparklan WX-7615A Manual de usuario

User’s Guide 0

Wireless 802.11ag AP Router

User’s Manual

Version 1.4

User’s Guide 1

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body.

If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor

environment only.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

The WX-7615A ( FCC ID: RYK-7615A ) is limited in CH1~CH11 for 2.4 GHz by specified firmware

controlled in U.S.A.

User’s Guide 2

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any

means, whether electronic, mechanical, photocopying, recording, or otherwise without the prior writing of the

publisher.

March. 2005

User’s Guide 3

Contents

1. Introduction............................................................................................................... 4

2. Safety Notification .................................................................................................... 5

3. Hardware Installation................................................................................................ 6

4. How to Configuring the Dual Band Router............................................................. 9

4.1 Setup – Basic Setup ............................................................................................. 10

4.2 Setup – DDNS........................................................................................................ 13

4.3 Setup – MAC Address Clone................................................................................ 14

4.4 Setup – Advanced Routing .................................................................................. 15

4.5 Wireless – Basic Wireless Settings..................................................................... 16

4.6 Wireless – Wireless Security ............................................................................... 17

4.7 Wireless – Wireless MAC Filter............................................................................ 18

4.8 Wireless – Advanced Wireless Settings ............................................................. 19

4.9 Security.................................................................................................................. 22

4.10 Access Restrictions – Internet Access Policy.................................................. 23

4.11 Application & Gaming – Port Range Forwarding............................................. 25

4.12 Application & Gaming – Port Range Triggering............................................... 27

4.13 Application & Gaming – DMZ............................................................................. 28

4.14 Application & Gaming –QoS .............................................................................. 29

4.15 Administration – Management........................................................................... 31

4.16 Administration – Log.......................................................................................... 33

4.17 Administration – Diagnostics ............................................................................ 34

4.18 Administration – Factory Defaults..................................................................... 35

4.19 Administration – Firmware Upgrade ................................................................. 36

4.20 Status – Router.................................................................................................... 37

4.21 Status – Local Network....................................................................................... 38

4.22 Status – Wireless Network ................................................................................. 39

5. Troubleshooting – Q & A........................................................................................ 40

User’s Guide 4

1. Introduction

Thank you for purchasing your Wireless 802.11ag AP Router.

This user guide will assist you with the installation procedure.

The package you have received should contain the following items:

Wireless 802.11ag AP Router

Quick Installation Guide

User Manual CD-ROM

Detachable Antenna

Universal AC/DC Power Adapter

RJ-45 Network Cable

Note: if anything is missing, please contact your vendor

User’s Guide 5

2. Safety Notification

Your Wireless AP Router should be placed in a safe and secure location. To ensure proper operation, please keep the unit

away from water and other damaging elements. Please read the user manual thoroughly before you install the device.

The device should only be repaired by authorized and qualified personnel.

Please do not try to open or repair the device yourself.

Do not place the device in a damp or humid location, i.e. a bathroom.

The device should be placed in a sheltered and non-slip location within a temperature range of +5 to +40 Celsius

degree.

Please do not expose the device to direct sunlight or other heat sources. The housing and electronic components may

be damaged by direct sunlight or heat sources.

3. Hardware Installation

Front Panel

The front panel provides LED’s for device status. Refer to the following table for the meaning of each feature.

Power The Power LED lights up and will keep while the Router is powered on. When the Router goes through

its self-diagnostic mode during every boot-up, this LED will flash. When the diagnostic is complete, the

LED will be lit continuously.

DMZ The DMZ LED indicates when the DMZ function is being used. This LED will remain lit as long as DMZ

is enabled.

11a The 11a LED flashes when there is a successful Wireless-A connection.

11g The 11g LED flashes when there is a successful Wireless-G connection.

Ethernet LED 1, 2, 3, 4. These numbered LEDs, corresponding with the numbered ports on the Router’s rear

panel. If the LED is continuously lit, the Router is successfully connected to a device through that port.

A flashing LED indicates network activity over that port.

Internet The Internet LED lights up when there is a connection built through the Internet port.

User’s Guide 6

User’s Guide 7

Rear Panel

The rear panel features 4 LAN ports, 1 WAN port and Reset button. Refer to the following table for the meaning of each

feature.

Internet LAN Power

RESET

RESET Button The RESET button can restore device to factory default settings by press this button for approx. 10

seconds during device power on status.

Internet The Internet port is where you will connect your broadband Internet connection.

LAN

1,2,3,4 These ports (1, 2, 3, 4) connect the Router to your networked PCs and other Ethernet network devices.

Power The POWER port is where you will connect the power adapter.

AP Router Default Settings

User

Password admin

IP Address 192.168.1.1

Subnet Mask 255.255.255.0

RF ESSID A band: wlan-a G band: wlan-g

Channel A band: Auto G band: 6

Mode G band: Mixed

Encryption Disabled

DHCP Server Enabled

User’s Guide 8

Hardware Installation for Connection to Your Broadband Modem

1. Power off your network devices.

2. Locate an optimum location for the Router. The best place for the Router is usually at the center of your wireless

network, with line of sight to all of your wireless devices.

3. Adjust the antennas. Normally, the higher location of your Router will get better the performance.

4. Using a standard Ethernet network cable, connect the Router’s Internet port to your broadband modem.

5. Connect your network PCs or Ethernet devices to the Router’s LAN ports using standard Ethernet network cabling.

6. Connect the AC power adapter to the Router's Power port. Then connect the other end to an electrical outlet. Only

use the power adapter supplied with the Router. Use of a different adapter may cause product damage.

7. The Hardware installation is complete, please refer to the following content for Router configuration.

User’s Guide 9

4. How to Configuring the Dual Band Router

TURN ON POWER SUPPLY

Quick power cycle would caused system corruption. When power on, be careful not to shut down in about 5 seconds,

because data is writing to the flash.

START UP & LOGIN

In order to configure the Wireless 11ag Router, you must use web browser and manually input http://192.168.1.1 into the

Address box and press Enter. The Main Page will appear.

In order to configure the Wireless 11ag Router, you must input the password into the Password box and leave blank on

the User Name box. The default password is “admin”.

Once you have logged-in as administrator, it is a good idea to change the administrator password to ensure a secure

protection to the Wireless 11ag Router. The Security Settings section described later in this manual describes how to

change the password.

Once you have input the correct password and logged-in, the screen will change to the Setup page screen.

Tabla de contenidos

Otros manuales de Enrutador de red de Sparklan

Sparklan

Sparklan WRTR 141 Manual de usuario

Sparklan

Sparklan WRTR-300 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad