Southco EA-R03 Manual de usuario

EA-R03 Wireless Keypad Controller Kit

Operating Instructions

J-EA-R03-M_revC visit www.southco.com for latest version of this document Page 1 of 4

Package Contents

EA-R02-202 Receiver

EA-R03-103 Wireless Keypad Transmitter

Keypad Mounting Packet

Power/Auxiliary Connector Wire Harness

Lock/Unlock Relay Connector Wire Harness

User Instructions

EA-R03-103 Wireless Keypad Transmitter

1·2 3·4 5·6 7·8 9·0

EA-R02-202 Receiver

1. Antenna

2. Access Tab for Programming Switches

Features

Receiver supports up to four transmitters (one pre-programmed

wireless keypad transmitter included with kit)

Re-programmable user code (3 to 7 digits)

Selectable LOCK/UNLOCK pulse duration (250ms or 10sec)

Backlit keypad keys

Two user-configurable lock/unlock relay outputs

One 12V auxiliary relay output.

Specifications

Receiver Power: 12VDC (±10%)

Receiver Idle Current: 10mA (maximum), no attached devices

Receiver Operating Current: 100mA (maximum), no attached devices

Receiver Outputs: three Form C relays, rated 15A at 14VDC

Receiver Operating Temp: -20 to 80°C

Operating Range: up to 60 feet / 18 meters (open air)

Operating Frequency: 433.92MHz

Coding Type: Fixed Code (24-Bit)

Transmitter Power: Type CR2032 3VDC battery

Normal Use

The keypad transmitter can be used to lock and unlock the system.

Unlocking the System

Enter the user code (default 1234), then press the 1·2 button. The system

will unlock and the auxiliary output will pulse twice, as shown in the figure

below:

UNLOCK Sequence (pulse set for 250ms)

UNLOCK Sequence (pulse set for 10 seconds)

Locking the System

Enter the user code (default 1234), then press the 3·4 button. The system

will lock and the auxiliary output will pulse once, as shown in the figure

below:

LOCK Sequence (pulse set for 250ms)

LOCK Sequence (pulse set for 10 seconds)

Pulsing Auxiliary Output

Enter the user code (default 1234), then press the 5·6 button. The auxiliary

output will pulse five times, as shown in the following figure:

EA-R03 Wireless Keypad Controller Kit

Operating Instructions

J-EA-R03-M_revC visit www.southco.com for latest version of this document Page 2 of 4

Changing the User Code

The unit is shipped with a default user code of 1234, but can be changed

to a 3-7 digit number. To change the user code:

1. Press the 9·0 button for approximately 3 seconds. Keypad lights

will flash twice then stay on.

2. Enter the current user code. When entering the last digit of the

current user code, hold the button for approximately 2 seconds.

Keypad lights will flash once then stay on.

3. Enter the new user code. When entering the last digit of the new

user code, hold the button for approximately 2 seconds. Keypad

lights will flash once then stay on.

4. Repeat the new user code. When entering the last digit of the

new user code, hold the button for approximately 2 seconds.

5. Keypad lights will flash once then turn off. The user code has

been successfully changed.

If the keypad lights turn off during Steps 1-4, then programming has been

timed out and the process needs to be repeated from Step 1.

NOTE: Refer to “Resetting the User Code” section if the user code

is lost or forgotten.

Enrolling Transmitters and Setting LOCK/UNLOCK Pulse Duration

Enrolling additional transmitters or setting the LOCK/UNLOCK pulse

duration will require access to the programming switches on the EA-R02-

202 receiver’s circuit board. To access the switches, remove the switch

access tab by sliding the tab away from the receiver unit as shown below.

Two switches will be visible thru the tab window (default positions shown):

Switch1 – Used to enroll transmitters. Default setting = “OFF”

position.

Switch 2 – Used to set LOCK and UNLOCK pulse duration:

Switch2 Setting

Duration

ON (default) 250ms (default)

OFF 10sec

NOTE: The switch access tab must always be re-installed when done

changing the settings.

Enrolling Transmitters

The EA-R03 kit is shipped with one EA-R02-202 receiver and one pre-

enrolled EA-R03-103 keypad transmitter. This transmitter is ready to use

with the receiver.

Up to four compatible transmitters can be enrolled with the receiver. To

enroll a transmitter:

1. Verify receiver has 12VDC power supply.

2. Move Switch1 from OFF to ON position, as shown below. The

auxiliary output will turn on.

3. Within six seconds of moving Switch1 to the ON position, enter

the current user code of the new keypad (e.g. 1234), then press

the 1·2 button. The auxiliary output will pulse to indicate the

transmitter has been enrolled.

4. If additional keypads are to be enrolled, enter the current user

code of the new keypad (e.g. 1234), then press the 1·2 button

within three seconds of enrolling the previous transmitter. The

auxiliary output will pulse twice to indicate transmitter #2 has

been enrolled, three times to indicate transmitter #3 has been

enrolled, and four times to indicate transmitter #4 has been

enrolled.

EA-R03 Wireless Keypad Controller Kit

Operating Instructions

J-EA-R03-M_revC visit www.southco.com for latest version of this document Page 3 of 4

5. Move Switch1 from ON to OFF position, as shown below:

6. Issue a LOCK or UNLOCK command from the transmitter to

verify successful enrollment.

NOTE: Enrolling any transmitters after moving Switch1 from OFF to

ON will cause all previous transmitters that were enrolled to be erased

and require re-programming to that receiver.

Setting LOCK/UNLOCK Pulse Duration

The EA-R02-202 receiver is shipped with the LOCK/UNLOCK pulse

duration set to 250ms.

The pulse duration of the LOCK and UNLOCK outputs can be set by

setting Switch2, shown below. Set the switch to the ON position for 250ms

output. Set the switch to the OFF position for 10 second output.

CAUTION: Be sure the LOCK/UNLOCK pulse duration is appropriate

for the latch or actuator connected to the EA-R02-202 receiver.

Resetting the User Code

If the keypad user code is lost or forgotten, it is possible to reset to the

factory default (1234). The keypad will remain enrolled with the receiver if

it is reset.

The keypad is shipped with a production date code label affixed to the

housing as shown in the following location:

The production date code is unique to each keypad. Each production date

code corresponds to a unique supervisor code that is required to reset the

user code. To obtain the supervisor code, contact Southco and provide the

production date code for your keypad.

Once the supervisor code is provided, perform the following to reset the

user code to 1234:

1. Press the 9·0 button for approximately 3 seconds. Keypad lights

will flash twice then stay on.

2. Enter the supervisor code provided by Southco. When entering

the last digit of the supervisor code, hold the button for

approximately 3 seconds. Keypad lights will flash, then turn off.

If the keypad is near the receiver, the receiver will issue an

‘unlock’ command and the auxiliary output will pulse.

NOTE: It is important to keep the production date code. The

keypad user code cannot be reset without the production date code.

It is suggested the user writes the production date code here and store

these instructions in a safe location. After writing down the production date

code and storing the instructions, the label should be removed from the

keypad.

Production Date Code: ____________________________________

Transmitter Battery Replacement

Replace the transmitter battery with a Type CR2032 3VDC battery. The

battery can be replaced by removing the screws on the back of the keypad,

then opening the enclosure.

EA-R03 Wireless Keypad Controller Kit

Operating Instructions

J-EA-R03-M_revC visit www.southco.com for latest version of this document Page 4 of 4

Receiver Unit Mounting and Wiring

The receiver should be mounted in a location to minimize RF shielding.

Two mounting screw bosses are provided to mount the receiver.

Power Supply and Auxiliary Output Connector

Pin #

Descripti

1 VCC (+12VDC Power Supply Input)

2 GND (Ground)

3 Auxiliary Output (Vout = VCC)

LOCK & UNLOCK Relay Connector

Pin #

Description

1 LOCK Relay – Normally Closed

(typically connect to GND)

2 LOCK Relay – Common

3 LOCK Relay – Normally Open

(typically connect to VCC)

4 UNLOCK Relay – Normally Closed

(typically connect to GND)

5 UNLOCK Relay – Common

6 UNLOCK Relay – Normally Open

(typically connect to VCC)

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. this device may not cause harmful interference and

2. this device must accept any interference received, including

interference that may cause undesired operation of the device.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE

1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of

March 9, 1999 on radio equipment and telecommunication terminal

Equipment and the mutual recognition of their conformity (R&TTE).

The R&TTE Directive repeals and replaces in the directive 98/13/EEC

(Telecommunications Terminal Equipment and Satellite Earth Station

Equipment) as of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those

who install and use it. However, special attention must be paid to the

dangers of electric shock and static electricity when working with electrical

equipment. All guidelines of this and of the computer manufacture must

therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland,

Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the

United Kingdom.

The ETSI version of this device is also authorized for use in EFTA ember

states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not Intended for Use

None.

For technical support of this product contact: info@southco.com

or visit: www.southco.com.

Este manual sirve para los siguientes modelos

Otros manuales de Controladores de Southco

Southco

Southco EA-KC2-201 Manual del propietario

Southco

Southco EA-P3-200 Manual de usuario

Southco

Southco EA-P1 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario