Soundstream Granite 120.4 Manual de servicio

SOUNDSTREAM

Granite 60.2,

Granite 120.4 and

Granite 180.6

POWER

AMPLIFIERS

OWNER’S MANUAL &

INSTALLATION GUIDE

CONGRATULATlONS

You now own the Soundstream Granite Amplifier, the result of a unique design and

engineering philosophy.

To maximize the performance of your system, we recommend that you thoroughly

acquaint yourself with its capabilities and features. Please retain this manual and

your sales and installation receipts for future reference.

Soundstream amplifiers are the result of American craftsmanship and the highest

quality control standards, and if properly installed, should provide you with many

years of listening pleasure. Should your amplifier ever need service or replacement

due to theft, please record the following information, which will help protect your

investment.

Model

Serial Number

Dealer’s

Name

Date of Purchase

Installation Shop

Installation Date

CAUTION!

Prolonged listening at high levels may result in hearing loss. Even though your new

Soundstream amplifier sounds better than anything you’ve ever heard, exercise

caution to prevent hearing damage.

DESlGN

FEATURES

Handcrafted

in the U.S.A. with mil-spec glass epoxy circuit boards, low-loss con-

nections, gold plated input connectors, and metal film resistors.

Darlington High Current Discrete Output Topology

Soundstream’s “overbuild

ing” of the output section incorporates Darlington output devices sandwiched

between the circuit board and the heat sink in a design called

ChassisinkTM

ensure cool, efficient amplifier operation.

Mixed Mono Capable so you can simultaneously drive a stereo and mono load

(satellites and subwoofer).

2 Ohm Drive Ability

The Granite amplifiers are designed to drive loads all the

way down to 2 Ohms stereo and 4 Ohms bridged.

Built-in Staggered Asymmetrical Crossovers (Granite 120.4, Granite 180.6)

Built-in electronic crossovers are designed to compensate for the acoustics of

the automobile environment. A high pass crossover (at 150 Hz

dB/octave)

and low pass crossover (at 75 Hz

dB/octave)

allow you to drive a com-

plete subwoofer and satellite system without the use of passive crossovers.

l Internal Signal Routing (Granite 120.4, Granite 180.6)

Permits one pair of

signal cables to drive all 4 channels (Granite 120.4) or two pairs of signal cables

to drive all 6 channels (Granite 180.6).

l Drive Delay Muted

Tunum/off

Circuit

unique circuit which completely elimi-

nates any amplifier-related turn-on/off noises.

l Flexible Input Sensitivity

accepts input voltages from 100

to 2.5 V, which

permits maximum output from amplifier with virtually any source unit.

*“Balancing Act” Input Topology

for added immunity to ground loops caused by

component and vehicle electrical system interaction.

Your Granite amplifier comes with a limited warranty. Refer to the enclosed

warranty card for length of warranty and conditions.

SPECIFlCATIONS

POWER OUTPUT

Power into

Power into Bridged Power

Ohms

Ohms into 4 Ohms

Granite 60.2

3Owx2 5Owx2

loowxl

Granite

120.4

3owx4 5owx4

lOOWx2

Granite 180.6

.3Owx6

50~x6

lOOwx3

THD <

O.l%, 20Hz-20kHz at rated power into 4 ohms

S/N Ratio

>90

Damping Factor

>200

Input Sensitivity 100

2.5 V

Dimensions (W x D x H)

Granite 60.2 7” x

&3/16”

2-3/16”

Granite 120.4

95/8”

83/16”

2-3/16”

Granite 180.6 12” x

83/8”

2-3/16”

GRANITE

60.2

Side View

MONO STEREO STEREO

MAIN FUSE

-0

Underside

View

Connected to fuse or circuit breaker, then battery’s positive post.

2. Ground

Main ground connection. Bolt to a clean chassis ground in the vehicle.

3. Remote

Remote

tumon

input from the head unit. Accepts +12V.

4. LED

Indicates amplifier power on.

Speaker Output

ConnectIons

Channels

)

6. Input Level

Variable from 100mV to 2.5V (Channels 1 +2).

7. Inputs

Right and Left Channel inputs; only right channel input used in “Mono” position.

[underside]

Mono/Stereo/Stereo Switch

Select “Mono” for bridged operation (only use

right channel input) or either Stereo position for

2channel

Stereo or Mixed Mono operation.

9. [underside] Main Fuse

Main power supply fuse. Replace only with same value.

GRANIlE120.4

.->A-

0’

-,--I

15’ 6

‘7

Side View

CflOnllOlS3UldA

Channets 1 and 2

MONO

r~~oi

MONO

STEREO

twut

tnprt

twut

Right

FKlm3u

ficm3+4

tnpur tnput

tnwt

FmmRkJht

Ffom1+2

Fmm3+4

L-J Underside View

1. +I2V

Connected to fuse or circuit breaker, then battery’s positive post.

2. Ground

Main ground connection. Bolt to a clean chassis ground in the vehicle.

3. Remote

Remote turn-on input from the head unit. Accepts

+12V.

4. LED

indicates amplifier power on.

5. Speaker

Du@ut

Connections

Channels

)

6. Input Level

Variable from

100mV

to 2.W (Channels

2).

7. Inputs

Standard RCA style connectors (Channels

I+

2). Right channel only for mono.

8. Speaker

Output

Connections

(Channels 3 + 4)

9. Input Level -Variable from

1OOmV

2.5V

(Channels 3 + 4).

10. Inputs

Standard RCA style connectors (Channels 3 + 4). Right channel only for mono.

11.

[underside]Channels

3 + 4

Mono/Stereo

(input 3 +

4)/Stereo

(input 3 + 4) Switch

MONO position for single channel operation (only right channel is active in Mono). Use

either STEREO input position with RCA inputs from Channels 3 + 4.

12. [underside] Channels 3 + 4

Cnwsover

Select either full range or high pass

(150H2,

12dB/octave)

operation.

13. [underside] Channels

2 Mono/Stereo (input

Stereo (input 3 + 4)

Switch

MONO position for single channel operation (only right channel is active in Mono). Use

“STEREO

1+2”

for RCA inputs

1+2.

Use “STEREO

3+4”

for RCA input

3+4.

14. [underside] Channels 1 + 2 Crossover

Select either full range or low pass

(75H2,

12dB/octave)

operation.

15. [underside] Main Fuse

Main power supply fuse, replace only with same value.

GRANITE180.6

UndersIde

View

+I2V

Connected to fuse or circuit breaker, then battery’s positive post.

2. Ground

Main ground connection. Bolt to a clean chassis ground in the vehicle.

3. Remote

Remote turn-on input from the head unit. Accepts +12V

4. LED

Indicates amplifier power on.

5. Speaker Output

Connections

Channels

)

6. Input Level

Variable from

1OOmV

to 2.5V (Channels 1 + 2).

7. Inputs

Standard RCA-type connectors (Channels

1 +

2). Use only right channel for mono.

8. Speaker Output Connections

(Channels 3 + 4)

9. input

level

Variable from 100mV to 2.5V (Channels 3 + 4).

10. Inputs

Standard RCA-type connectors (Channels 3

+4).

Use only right channel for mono.

11. Speaker Output Connections

(Channels 5 + 6)

12. Input Level -Variable from

IOOmV

to 2.5V (Channels 5 + 6).

13. Inputs

Standard

RCAtype

connectors (Channels 5

+6).

Use only right channel for mono.

14. [underside] Channels 5 + 6 Mono/Stereo (input 5 + 6)

Stereo (input 3 + 4) Switch

MONO position for single channel operation. (Only right channel is active in Mono) Use

“STEREO

5+6”

for RCA inputs

5+6.

Use “STEREO

3+4”

for input from

RCAs

3+4.

15. [underside] Channels 5 + 6 Crossover

Full range or high pass

(150Hz,12dB/octave).

16. [underside] Channels 3 + 4 Mono/Stereo (input 3 + 4)

Stereo (Input 3 + 4) Switch

MONO position for single channel operation. (Only right channel is active in Mono) Use

either STEREO input position with RCA inputs from Channels 3 + 4.

17.

[undersidejchannels

3 + 4 Crossover

Full range or high pass (150Hz,

12dB/octave).

18. [underside] Channels

+ 2 Mono/Stereo (input

I+

Stereo (input 3 + 4) Switch

MONO position for single channel operation (only right channel is active in Mono). Use

“STEREO

1+2”

for RCA inputs

1+2.

Use ‘STEREO

3+4”

for input from

RCAs

3+4.

19.

[unde&de]Chann&

1 +

2 Crossover

Full range or low pass (75Hz,

12dB/octave).

20. [underside] Main Fuse

Main power supply fuse, replace only with same value.

SPEAKER

WBRlNG

CONFlGlJRAVlONS

(per pair of channels)

STEREO

MONO

Use

R inputs

Use Right input only

MIXED MONO

Use

R inputs

STEREO

MONO

STEREO MONO

STEREO

SWITCH SETTINGS (bottom of amp)

For each pair of’channels, there are two switches (one on 60.2) accessible from

the bottom of the amplifier.

Mono/Stereo Switch:

Set to “Mono” to bridge one pair of channels into a

single channel. Only Right channel input is active. When in “Stereo,” a mono

channel can be driven using Left

& Right + speaker outputs.

Crossover

Switch

(Granite 120.4, Granite 180.6): Defeatable high or low

pass crossover. Frequencies are set at 150 Hz, 12 dB/octave on the high

pass and 75 Hz, 12 dB/octave on the low pass.

Following are several possible system configurations driven by a single or two

bridged Granite amplifiers.

1. Granite

60.2

2 Channel Input

2 Channel Output

HEAD UNIT

MONO STEREO STEREO

AMPLIFIER

+‘I_

+.L

FULL-RANGE

SPEAKERS

2. Granite 60.2

Channel Input

Channel Output

]

MONO STEREO STEREO

AMPLIFIER

+B-

+L-

SATELLITES

SUBWOOFER

Granite

60.2

Single Input

Bridged Amps Output

AMPLIFIER

-A

I. R

MONO STEREO STEREO

A*-

*L_

LECT

FULL-RANGE

SPEAKER

AMPLIFIER

I-I

MONO STEREO STEREO

SPEAKER

4. Granite

120.4

Channel

Full Range

AMPLIFIER

Channels 3 and 4 ch8nnels

and

MONO STEREO MONO STEREO

Granite

120.4

2 Channel Full Range

---1

AMPLIFIER

Channels 3 and 4 Channels 1 and 2

MONO STEREO

33~

MONO STEREO

G-z

“,S@

PASS

R?kE l%!z

R%k

+R-

+‘L_

+a_

+*L

Granite 320.4

Channel

Satellites/2 Subwoofers

HEAD UNIT

Channels

and

MONO STEREO

3J+i

Channels

and

MONO STEREO

15-Z

AMPLIFIER

SATELLITE

SPEAKERS SUBWOOFERS

Granite

120.4

3 Channel

Satellites/Subwoofer

Channels

and

Channels

and

MONO

FTERE?

MONO STEREO

3+4

13+4

AMPLIFIER

+=_

+‘_

+=-

SATELLITE

SPEAKERS SUBWOOFER

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de Soundstream

Soundstream

Soundstream STEALTH Series Manual de usuario

Soundstream

Soundstream RUBICON 204 Manual de programación

Soundstream

Soundstream LIL WONDER II Manual de usuario

Soundstream

Soundstream HRU. 2 Manual de usuario

Soundstream

Soundstream Rubicon RUB600-4 Manual de programación

Soundstream

Soundstream CLASS-A-5.0 Manual de usuario

Soundstream

Soundstream USB.8A Manual de usuario

Soundstream

Soundstream RUBICON 255 Manual de programación

Soundstream

Soundstream Picasso P1.210 Manual de usuario

Soundstream

Soundstream SMA2.340 Manual de usuario

Soundstream

Soundstream Picasso Manual de servicio

Soundstream

Soundstream Reference 705s Manual de programación

Soundstream

Soundstream L1.600D Guía de solución de problemas

Soundstream

Soundstream Di175.1 Manual de usuario

Soundstream

Soundstream RUBICON 1002 Manual de programación

Soundstream

Soundstream SA 164 Manual de programación

Soundstream

Soundstream Tarantula Amplifier Series Manual de usuario

Soundstream

Soundstream Rubicon 102 Manual de programación

Soundstream

Soundstream Stealth ST1.700D Manual de usuario

Soundstream

Soundstream LW1.350 Manual de programación

Soundstream

Soundstream LIL WONDER LW1.400 Manual de usuario

Soundstream

Soundstream D'Artagnan5.1 Manual de programación

Soundstream

Soundstream Rubicon RUB550-5 Manual de usuario

Soundstream

Soundstream Rubicon 1000D Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario