Soundoff Signal NERGY bluePRINT ENGND04101 Manual de usuario

EVCS_Remote Node_ENGND04101 1.15

1.800.338.7337 / www.soundoffsignal.com

NOTICE:

Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.

Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at

www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the

automated message). Questions or comments that do not require immediate attention may be emailed to [email protected].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

Please see next page for

Technical Speciﬁcations

REMOTE NODE

PART NUMBER: ENGND04101

The Remote Node provides 10 outputs for connection to

vehicle devices (50 Amps max).

 •(4)10-ampsolidstateswitchableoutputs

 •(6)5-ampsolidstateswitchableoutputs.

TheRemoteNodealsoprovides4inputstocontrolsystems.

 •ActiveHigh/Lowselectable.

See attached Install Template to aid in connections and programming

+(Power)

-(Ground)

Wire

Pin #

Wire

Function Amp

1 OUTPUT 9 10 Amp

2 OUTPUT 8 5 Amp

3 OUTPUT 7 10 Amp

4 OUTPUT6 5 Amp

5 OUTPUT 5 5 Amp

6 OUTPUT4 10 Amp

7 OUTPUT 3 5 Amp

8 OUTPUT 2 10 Amp

9 OUTPUT 10 5 Amp

10 INPUT 1*

11 INPUT 2

12 INPUT 3

13 INPUT4

14 ADDRESS

SELECT

15 DATA

16 OUTPUT 1 5 Amp

PIN 1

PIN 8

PIN16

PIN 9

OUTPUTINDICATORLED’S

FOROUTPUTS1-10

ADDRESSINDICATORLED

DIAGNOSTICINDICATORLED

ACTIVELOW

ORHIGH

MOMENTARY

ACTIVEHIGH

AUTOMOTIVE50

AMP MAX FUSE

OR BREAKER

*Input1canbeusedasgeneralpurposeinput

orasasystemignitioninput.

Higherinrushcurrentthreshold-Xenon

VBATT

DIRECTBATTGROUND

CONNECTION

•HIGHCURRENTinterconnectsmustbeproperlyterminated.Poorcrimpqualitycancauseheat

build-upandre.Followcrimpconnectormanufacturerinstructions.

•DONOTinstallthisproductorrouteanywiresintheAirBagDeploymentZone.Refertovehicle

Owner’sManualfordeploymentzones.

•DoNOTusesystemtodisconnectheadlights,brakelightsorothersafetyequipment.

•Unitmaybecomehottotouchduringnormaloperation.

•Failuretoproperlyinstallconnectors,fusesorwiringmaycausevehiclefailureorre.

•Installationmustonlybeperformedbytrainedtechnician.Installermustdeterminevehiclewiring

congurationandproperintegrationofsystem.

•Useproperwiregauge.Allpowerwiresconnectingtopositive(+)ornegative(-)batteryterminal

orlocalchassisground(-)mustbesizedtosupplyatleast125%ofmax.currentandproperlyfusedat

powersource.

•Installprotectivegrommetswhenroutingwirethroughrewallormetal.

WARNING

EVCS_Remote Node_ENGND04101 1.15

1.800.338.7337 / www.soundoffsignal.com

NOTICE:

Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.

Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at

www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the

automated message). Questions or comments that do not require immediate attention may be emailed to [email protected].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

SETTING NODE ADDRESS

To set the node addresses:

1.MomentarilyconnectpowertoPIN14.

2.AddressindicatorLEDwillwinktheaddress(1-5).

NOTE:

•Defaultaddressis1.

•Afteraddress1issetitwillcyclethroughtheaddressesuntilitgetsbackto1.

DIAGNOSTIC LED

•ThediagnosticLEDissteadyonwhenthedeviceispoweredupandrunningwithnoerrors.

•ThediagnosticLEDisoffwhenthedeviceisofforinsleepmode.

•ThediagnosticLEDwinkswhenthereisasystemfaultofthedeviceisinrmwareupgrademode.

 •FaultconditionisreadbycountingthenumberoftimestheLED  

“winks”on.Eachfaultconditionwillgenerateapatternwhereeach“wink”is250ms

off/250mson.ThepatternisterminatedbytheLEDbeingofffor2.5seconds.

 •TheLEDwillwinkmultiplepatternswhenmorethanonefaultconditionisactive.

FAULT CONDITION PATTERNS:

1Wink-RPDUoutput(s)arefaulted

2Winks-Communicationfault

3Winks-Sourcevoltagelevelis<9VDC

4Winks-Sourcevoltagelevelis>16VDC

5Winks-Overtemperaturecondition

Bydefaultevenoutputsashalternatingwithoddoutputs.

Tech Specs

nERGY Control System Remote

Node

Input Voltage: 10-16Vdc(NegativeGround)

Maximum Input Current: 50 Amps (30Amps at 85°C)

Outputs (Sum of ALL used Outputs

Shall Not Exceed 50Amps)

4x10AmpSolidState,Switched

6x5AmpSolidState,Switched

IGN ON: Standby Current: 60mA

IGN OFF: Sleep Current: 0.34mA

Inputs:

4xTotal

3xActiveHigh/LowInputs

*1xActivehigh/LowInputw/SystemWakeup

Reverse Polarity Protection: NotProtected(ReversePolaritywillDestroytheDevices)

Transient Protection: Protected

High Voltage Protection: >16V;HighVoltageErrorCodeSet

Low Voltage Protection: <9V;LowVoltageErrorCodeSet

Operating Temp: -40˚Cto+65˚C(85°Cmaxcurrent=30Amps)

Dimensions: 6.0”x3.4”x.8”

Weight, Boxed: 13.2oz.

Weight, Device Only: 10.7oz.

Valid Input Threshold High: >8.0V

Valid Input Threshold Low: <1.5V

Hermeticallysealedprovidingprotectioninwetareas.

•Installfuseorbreaker(50Ampsmax.)onmainpowersupply.

•DoNOTconnectproducttostrobepowersupply.Productisself-contained;noexternalpowersupply

needed.

•FollowattachedWiringandInterconnectrequirements.

•Torque the provided M8 nuts with lock washer to a maximum of 7ft-lbs.

-Verify that the lockwasher is fully seated when assembled-

WARNING

*Input1canbeusedtosenseignitionstatusforoverallsystemoperation

Multi-colorlightsshouldbedrivenbyoutputswithinthesameoutputgroup

(Group1:1-5,Group2:6-10)toaligntiming.

Bydefaultevenoutputsashalternatingwithoddoutputs.

EVCS_Remote Node_ENGND04101 1.15

1.800.338.7337 / www.soundoffsignal.com

NOTICE:

Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.

Improper use or installation may void warranty coverage. To review our Limited Warranty Statement & Return Policy for this or any SoundOff Signal product, visit our website at

www.soundoffsignal.com/sales-support. If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. at 1.800338.7337 (press #4 to skip the

automated message). Questions or comments that do not require immediate attention may be emailed to [email protected].

SUPERIOR CUSTOMER RELATIONSHIPS. SMARTLY DESIGNED LIGHTING & ELECTRONIC SOLUTIONS.

Wiring and Interconnect Requirements for ENGND04101 Remote Node

•Highcurrentinterconnectsrequirecarefulterminationwiththeproperequipment. WARNING! Poor crimp quality can cause signiﬁcant heat build-up and ﬁre.Followconnector

manufacturerinstructionstoterminateproperly.

•RemoteNodecanswitchuptoatotal maximum of 50Amps.Usermustcongureoutputstonotexceedthistotalcurrent.Individualoutputswitchesareratedupto10Ampseachforhigher

currentloads,but the total device current must not exceed 50Amps.Thesoftwarewarnswhentheselimitsareexceededandusermustensurethatindividualoutputlimitsandtotaldevice

current limits are not exceeded in normal use.

•Do not gang or parallel multiple outputs to drive a high current load. Multiple5Ampand10Ampoutputsmustnotbecombinedtoachieveahighercurrentlimit.

TERMINATION OPTION 2

Purchaseindividualconnectorcomponentstoterminatethewiresattheconnector.

Molex P/N:19418-0030 Molex P/N:19420-0001 Molex P/N: 19417-0119

MX150L™16CircuitSealed

Receptaclefor14-16AWGWire

MX150L™FemaleTerminalfor14-16AWG

Wire,TinPlated

MX150L™SocketPlug/Key(Oneplugre-

quiredforeachunusedpinlocationtoseal)

•MX150LAssemblyInstructions:http://www.molex.com/pdm_docs/as/AS-19417-001.pdf

•ApplicationToolingSpecicationSheet:http://www.molex.com/pdm_docs/ats/ATS-6381144HM.pdf

•QualityCrimpingHandbook:http://www.molex.com/pdm_docs/ats/TM-638000029.pdf

•Actualterminalandhousingsmaybedifferentdependingonapplication,wiretype,etc.

•HandCrimpTool:Molex P/N:63811-4400

•ManualExtractionTool: Molex P/N:63813-1500

•WARNING! Wire diameter with insulation must be 0.113in to 0.139in (2.87mm-3.53mm) to properly seal

(suchasSXL16AWG)

Pros: •Consistentwirecolors,cleaninstallwithoutbutt-splices

Cons: •Needtopurchasecrimperandtrainpersonnel

WARNING

TERMINATION OPTION 1

PurchaseaccessorymatingharnessfromSoundOffSignal

SoundOff P/N:ENGHNK02(16pinMatingHarness)

•Typicallyawatertightbutt--splicewithglueisusedto

protectthisterminationandisrequiredforexterioruse.

Pros: •No need to terminate at the connector pins

•NoneedtopurchaseMolexcrimper

Cons: •Requiresbutt-spliceoralternateconnector

•Requiresheatshrinktubingwithglueforexterior

Striptothislength

(drawntoscale)

0.165”to0.197”

Insulation

Crimp

0.006”to

0.026”

Pin 1, Output 9, 10A _ _________________________________ ________________

Pin 2, Output 8, 5A __________________________________ _______________

Pin 3, Output 7, 10A __________________________________ _______________

Pin 4, Output 6, 5A ____________________________________ _______________

Pin 5, Output 5, 5A ____________________________________ _______________

Pin 6, Output 4, 10A __________________________________ _______________

Pin 7, Output 3, 5A __________________________________ _______________

Pin 8, Output 2, 10A __________________________________ _______________

________________ __________________________________ 5A, Output 1, Pin 16

________________ __________________________________ 5A, Output 10, Pin 9

________________ ______________________________________ Input 1, Pin 10

________________ ______________________________________ Input 2, Pin 11

________________ ______________________________________ Input 3, Pin 12

________________ ______________________________________ Input 4, Pin 13

ID # __________ Module Select, Pin 14

________________ ________________________________________ DATA, Pin 15

EVCS_RemoteNode1.15

1.800.338.7337 / www.soundoffsignal.com

Department: _________________________________

Vehicle: ______________________________________

Installer / Date: ________________________________

Moun ng Loca on: _____________________________

REMOTE NODE

INSTALL TEMPLATE

AUTOMOTIVE50AMAX

FUSE OR BREAKER

Function WireColorFunction

WireColor

=XenonInrush

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario

Soundoff Signal nERGY bluePRINT ENGND04101 Manual de usuario

Manuales populares de Hardware de computadora de otras marcas