Soundcore Soundcore Life P2 Manual de usuario
Soundcore Life P2
01 EN
Charging
• Remove the protective lm from the earbuds when using for the rst time.
• Fully charge both the earbuds and the charging case before the rst use.
• To prevent damage, use the provided USB-C cable.
• Fully dry off the earbuds and the USB port before charging.
1
RR
2
LED indicators (Earbuds & Charging case)
Steady white Being Charging
Light off • Fully charged
• Remaining battery >10% (when in use)
Powering On/Off
The earbuds will automatically power on when taken out of the charging case and power off
when placed back into the charging case.
ON OFF
LED indicators (Earbuds)
ON Steady white for 1 second
OFF Steady red for 1 second
EN 02
• To manually power on, press the multi-function button on either one of the earbuds.
• To manually power off, press and hold the multi-function button on either one of the
earbuds for 3 seconds.
Pairing
True Wireless Stereo Connection
The right earbud will automatically connect with the left earbud when taken out of the
charging case.
LED indicators (Earbuds)
Breathing white TWS connecting
Steady white for 1 second TWS connected
• When powered off, press and hold the multi-function button on both earbuds for 1
second, the earbuds will enter TWS connecting mode.
• When powered on and connected, place either one of the earbuds into the charging case,
you can keep using the other one.
• When powered on and connected, if either one of the earbuds is out of battery and
powered off, you can keep using the other one.
• When you are on a call, place either one of the earbuds into the charging case, 3 to 5
seconds later, the microphone in the other earbud will be activated.
Bluetooth Pairing with your Device
The earbuds will enter pairing mode when powered on. You are requested to confirm the
connection when you see a pop-up.
Soundcore
Life P2
Bluetooth Pairing Request
“Headset” would like
to pair with your iPhone
Cancel Pair
Pair
03 EN
LED indicators (Earbuds)
Flashing white Bluetooth pairing
Steady white for 1 second Bluetooth connected
In the pairing process, some devices are incompatible with Qualcomm True Wireless Primary-
Secondary dual pairing names, it may notice “connection unsuccessful” when you tap “Pair”
or even no screen pops up. Don’t worry and it will not inuence the using.
Once successfully paired, the primary earbud connects with your device and transfers signal
to the secondary earbud, the latter one will not connect with your device. As a result, in the
Bluetooth pairing list on your device, it may indicate that only one side is connected while the
other side is not.
• To pair with another Bluetooth device, turn off Bluetooth on the currently connected
device rst.
• Each time you power on your Soundcore earphones, it will automatically connect to your
last successfully connected device if available within the Bluetooth range.
Wearing
1. Choose the EarTips that t your ears best.
2. Insert the earbuds into the inner canal of your ears.
3. Turn and nd the most comfortable position.
1 2
EN 04
Controls
Play / Pause
1
R\L
Press (R/L)
Next track
R
2
Press twice (R)
Previous track
2
L
Press twice (L)
Volume up / down Control volume via the connected device
Answer / End a call
1
R\L
Press (R/L)
Reject a call
1”
R\L
Press and hold for 1 second (R/L)
Enable mono mode Remove either one of the earbuds off your ear and press and hold
the button on the other earbud for 1 second
Activate Siri or other voice
assistant software
1”
R\L
Voice Assistant Press and hold for 1 second (R/L)
Reset
Reset the earbuds if the earbuds cannot connect with each other properly or cannot connect
with your device properly.
1. Place the earbuds into the charging case and make sure they are being charged.
2. Press and hold the button on both earbuds for 3 seconds until the LED indicators ash red 3
times and then turn white.
All the memory data will be cleared.
05 EN
3”
L
R
3
Specifications
Specications are subject to change without notice.
Input 5 V 500 mA
Rated output power 7 mW @ 1% THD
Battery capacity 55 mA x 2 (earbuds); 700 mA (charging case)
Charging time 2 hours
Playtime (varies by volume level and content) 7 hours (Totally 40 hours with the charging case)
Driver size 6 mm × 2
Frequency response 20 Hz - 20 kHz
Impedance 16 Ω
Bluetooth version V 5.0
Bluetooth range 10 m / 33 ft
Qualcomm® aptXTM Technical specications
Compression ratio: 4:1
Word depth: Support 16bit and 24bit
Decoding delay: Sample rate 48kHz<2ms
Dynamic range: 16bit>92dB, 24bit>120dB
Data rates: 352kbps
Decode mode: Stereo
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and
other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered
in the United States and other countries.
Otros manuales para Soundcore Life P2
3
Tabla de contenidos
Otros manuales de Auriculares de Soundcore
Soundcore
Soundcore Spirit 2 Manual de usuario
Soundcore
Soundcore Liberty 3 Pro Manual de usuario
Soundcore
Soundcore Life P2 Mini Manual de usuario
Soundcore
Soundcore Soundcore Life P2 Manual de usuario
Soundcore
Soundcore AeroFit Manual de usuario
Soundcore
Soundcore Life P2i Manual de usuario
Soundcore
Soundcore Vortex Manual de usuario
Soundcore
Soundcore P25i Manual de usuario
Soundcore
Soundcore Liberty 4 Manual de usuario
Soundcore
Soundcore Liberty Air 2 Manual de usuario
Soundcore
Soundcore Liberty Air 2 Pro Manual de usuario
Soundcore
Soundcore Life Note Manual de usuario
Soundcore
Soundcore Spirit Dot 2 Manual de usuario
Soundcore
Soundcore Life Q35 Manual de usuario
Soundcore
Soundcore Life Q20 Manual de usuario
Soundcore
Soundcore A3911 Manual de usuario
Soundcore
Soundcore Life Q10 Manual de usuario
Soundcore
Soundcore Life Note C Manual de usuario
Soundcore
Soundcore VR P10 Manual de usuario
Soundcore
Soundcore Life P3 Manual de usuario
